2003 FORD MUSTANG steering

DESCRIPTION AND OPERATION
Wheels And Tires
WARNING: Do not mix different types of tires, such as radial, bias, or bias- belted, on the
same vehicle except in emergencies. Vehicle handling can be seriously affected and can result
in loss of control.
Factory-installed tires and wheels are designed to operate satisfactorily with loads up to and including
full- rated load capacity when inflated to recommended inflation pressures.
Tire and Wheel Runout
Excessive radial and lateral runout of a wheel and tire assembly can cause roughness, vibration,
wheel tramp, tire wear, and steering wheel tremor.
Before checking runout, and to avoid false readings caused by temporary flat spots in the tires, check
runout only after the vehicle has been driven far enough to warm the tires. For additional information,
refer to Section 100 - 04 .
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
wheel bearing life.
z brake cooling.
New wheels need to be installed when vehicle's wheels:
zare bent.
z are cracked.
z are dented.
z are heavily corroded.
z are leaking.
z have elongated wheel hub bolt holes.
z have excessive lateral or radial runout.
Wheel and tire assemblies are attached by six wheel nuts.
It is mandatory to use only the tire sizes recommended on the tire chart attached to the vehicle. Larger
or smaller tires can damage the vehicle, affect durability, and require changing the speedometer
calibration. Make sure wheel size and offsets match those recommended for the tire in use. 1. Inspect for signs of uneven wear that may indicate a need for balancing, rotation, front suspension alignment, damaged tie- rod, or steering components.
2. Check tires for: zcuts.
z stone bruises.
z abrasions
z blisters.
z embedded objects.
3. Tread wear indicators are molded into the bottom of the tread grooves. Install a new tire when the indicator bands become visible.
Symptom Chart Symptom Chart Condition
Possible Sources Action
z Tires show
excess wear on
edge of tread z
Underinflated tires. zADJUST air pressure
in tires.
z Vehicle overloaded. zRETURN vehicle.
NOTIFY customer of
overload condition.
z High- speed cornering. zRETURN vehicle.
NOTIFY customer of
cause of condition.
z Incorrect ride height. zSET ride height.
z Incorrect wheel alignment. zSET alignment to
specification. REFER Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

to
Section 204 - 00 .
z Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Tires show
excess wear in
center of tread z
Tires overinflated. zADJUST air pressure.
z Other excessive
tire wear
problems z
Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Incorrect tire pressure. zADJUST pressure.
z Loose or leaking shock
absorbers. z
TIGHTEN or INSTALL
new shock absorbers
as necessary.
z Incorrect wheel alignment. zSET alignment to
specification. REFER
to Section 204 - 00 .
z Loose, worn or damaged
suspension components. z
REFER to Section 204 - 00 .
z Wheel and tire assembly
out of balance. z
BALANCE wheel and
tire assembly.
z Excessive lateral or radial
runout of wheel. z
REFER to Section 100 - 04 .
z Wobble or
shimmy z
Damaged wheel bearings. zREFER to Section 204 - 00 .
z Loose or damaged
suspension components. z
REFER to Section 204 - 00 .
z Bent wheel. zINSTALL a new wheel
as necessary.
z Damaged tire. zINSTALL a new tire as
necessary.
z Loose wheel nuts. zTIGHTEN to
specification.
z High- speed
shake z
Wheel hub face/pilot/bolt
circle runout.
z Tires/wheels.
z Wheel bearings.
z Suspension/steering
linkage.
z Engine.
z Transmission.
z Brake discs/imbalance. z
REFER to Section 100 - 04 .
z Vehicle vibration zDriveline — engine.
z Tires. z
REFER to Section 100 - 04 . Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Axle Housing
Removal
1. CAUTION: The vehicle must be on level ground and at curb height.
Mark the rear shock absorbers relative to their protective sleeve. zDuring installation, raise the suspension to this reference mark before tightening the
suspension component fasteners.
SECTION 205-
02C: Rear Drive Axle/Differential — Ford 8.8-Inch IRS 2003 Mustang Workshop Manual Special Tool(s)
Plug Set, Differential
205-
294 (T89P-4850- B) Protector, Differential Seal
(Pair)
205-
461 Remover, Halfshaft
205-
475 Remover, Steering Arm
211-
003 (T64P-3590- F) Klj . 1 ba
142003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Halfshaft
Removal
NOTE:
This procedure applies to both the LH and RH halfshafts.
1. CAUTION: The vehicle must be on level ground and at curb height.
Mark the rear shock absorber relative to the protective sleeve. zDuring installation, raise the suspension to this reference mark before tightening the
suspension component fasteners.
SECTION 205-
05: Rear Drive Halfshafts 2003 Mustang Workshop Manual Special Tool(s)
Differential Plug
205-
294 (T89P-4850- B) Differential Seal Protector
205-
461 Front Hub Remover
205-
D070 (D93P-1175- B) or
Equivalent Halfshaft Removal Tool
205-
475 Steering Arm Remover
211-
003 (T64P-3590- F) Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

For low or spongy brake pedal concerns:
zcheck and, if necessary, refill the brake master cylinder reservoir.
z bleed the brake system and retest the brake pedal feel.
z if the brake pedal is still low or feels spongy, check the brake pedal mounting for looseness and
correct installation. Check the power brake booster and the brake master cylinder for loose
mounting. Correct as necessary and retest the system for normal operation.
For a slow or incomplete brake pedal return concern:
zinspect for binding, damage, correct installation or interference at the brake pedal.
z check the power brake booster for binding, damage and correct installation.
Vibration When Brakes are Applied
For vibration concerns when brakes are applied, perform the following procedure.
Visually inspect: ztire condition and pressure.
z suspension bushings and ball joints.
Correct as necessary. 1. Verify and isolate the concern. Brake roughness can be felt in: zthe steering wheel.
z the seat.
z the brake pedal.
2. After verifying the concern, check for related concerns in the: zOn- Line Automotive Service Information System (OASIS).
z Technical Service Bulletins.
3. Check wheel bearing end- play and correct as necessary.
4. NOTE: Begin at the front of the vehicle unless the vibration has been isolated to the rear.
Remove the tire and wheel.
5. Remove the brake caliper.
6. Measure and record the brake disc thickness. Install a new brake disc if the thickness after machining will be at or below specification. The specification is molded into the brake disc. Do z
Power brake booster
z Brake pedal linkage
z Vacuum booster hose
z Tires
z Foreign material Klj . 3 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Pinpoint Tests
PINPOINT TEST A: THE BRAKES PULL OR DRIFT booster hose as
necessary.
z Red Brake Warning
Indicator Inoperative z
Circuit.
z Bulb. z
REFER to Section 413 -
01 .
z Brake Noise zDisc brake
component. z
MACHINE or INSTALL a
new brake component as
necessary. REFER to
Section 206 - 03 or
Section 206 - 04 .
z Hydro-Boost, No
Power Assist z
Power steering
pump.
z Linkage.
z Power steering
fluid flow.
z Hydro-boost unit. z
Go To Pinpoint Test E .
z Hydro-Boost Erratic
Operation, Sticks,
Binds or Grabs z
Supply hose.
z Hydro-boost unit. z
Go To Pinpoint Test F .
z Hydro-Boost Brake
System Operation
Suspect z
Leakage.
z Hydro-boost unit. z
Go To Pinpoint Test G .
Test Step Result / Action to Take
A1 CHECK THE TIRES
NOTE:
Check tire pressure with the brakes off.
z Check tires for uneven and excessive wear and for correct
pressure.
z Are the tires OK? Yes
GO to
A2 .
No
CORRECT as necessary.
RETEST for normal
operation. A2 CHECK THE ALIGNMENT
z
Check the caster, camber and toe. Refer to Section 204 -
00 . Yes
GO to
A3 .
No
CORRECT alignment as
necessary. REFER to Section 204 - 00 . RETEST for correct
operation. Klj . 6 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST D: EXCESSIVE/ERRATIC BRAKE PEDAL TRAVEL
PINPOINT TEST E: HYDRO-
BOOST, NO POWER ASSIST 4481 kPa (510-
650 psi)? INSTALL a new proportioning valve.
RETEST for normal operation.
Test Step Result / Action to Take
D1 CHECK FOR SPONGY PEDAL
z
Key in ON position.
z Operate the brake pedal and note pedal feel.
z Does the pedal feel spongy? Yes
BLEED the brake system. REFER to
Bleeding —
System in this section.
RETEST for normal operation.
No
GO to D2 .
D2 CHECK THE BRAKE PEDAL
z
Inspect the brake pedal and bracket for
binding, obstruction or damage.
z Is the brake pedal OK? Yes
GO to
D3 .
No
REPAIR or INSTALL a new brake pedal as
necessary. RETEST for normal operation. D3 CHECK THE BRAKE COMPONENTS
z
Inspect the calipers bolts, anchor plate bolts
and anti- rattle springs for binding, damage,
contamination and correct installation.
z Are the bolts and springs OK? Yes
GO to
D4 .
No
REPAIR or INSTALL new components as
necessary. RETEST for normal operation. D4 CHECK THE BOOSTER AND MASTER
CYLINDER z
Check the power brake booster and brake
master cylinder for correct installation and
correct push rod adjustment. Refer to
Section 206 - 06 and to Section 206 - 07 .
z Are the power brake booster and the
brake master cylinder OK? Yes
INSPECT the front wheel bearings for
wear, damage and correct installation and
the rear axle end play. CORRECT as
necessary. RETEST for normal operation.
No
CORRECT as necessary. RETEST for
normal operation.
Test Step Result / Action to Take
E1 CHECK FLUID LEVEL IN POWER STEERING
PUMP z
Check fluid level in power steering pump.
z Is level within specification? Yes
GO to
E2 .
No
CHECK for leakage of power steering
fluid. ADD fluid as necessary. E2 CHECK ACCESSORY DRIVE BELT Klj . 10 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...