2003 FORD MUSTANG steering

z
Clunk— noise from the
front suspension, occurs
in and out of turns z
Loose front
struts or shocks. z
INSPECT for loose nuts
or bolts. TIGHTEN to
specifications. REFER to
Section 204 - 01 .
z Clunk— noise from the
rear suspension, occurs
when shifting from
reverse to drive z
Loose rear
suspension
components. z
INSPECT for loose or
damaged rear
suspension components.
REPAIR or INSTALL
new components as
necessary. REFER to
Section 204 - 02 .
z Click or pop— noise from
the front suspension.
More noticeable over
rough roads or over
bumps z
Worn or
damaged ball
joints. z
CARRY OUT a ball joint
inspection. INSTALL
new ball joints or control
arms as necessary.
REFER to Section 204 -
01 .
z Click or pop (FWD
vehicles)—noise occurs
when vehicle is turning z
Worn or
damaged ball
joints. z
CARRY OUT a ball joint
inspection. INSTALL
new ball joints or control
arms as necessary.
z Click or snap— occurs
when accelerating around
a corner z
Damaged or
worn outboard
CV joint. z
INSPECT the outboard
CV joint and boot.
REPAIR or INSTALL a
new CV joint as
necessary.
z Front suspension noise—
a squeak, creak or rattle
noise. Occurs mostly over
bumps or rough roads z
Steering
components.
z Loose or bent
front struts or
shock
absorbers.
z Damaged
spring or spring
mounts.
z Damaged or
worn
control/radius
arm bushings.
z Worn or
damaged
stabilizer bar
bushings or
links. z
Go To Pinpoint Test H .
z Rear suspension noise—
a squeak, creak or rattle
noise. Occurs mostly over
bumps or rough roads z
Loose or bent
rear shock
absorbers.
z Damaged
spring or spring
mounts.
z Damaged or
worn control
arm bushings.
z Worn or
damaged
stabilizer bar
bushings or
links. z
Go To Pinpoint Test I .
z Shudder— occurs during zRear drive axle zCHECK the axle mounts Klj . 37 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

acceleration from a slow
speed or stop
assembly
mispositioned. and the rear suspension
for damage or wear.
REPAIR as necessary.
z Incorrect or high
CV joint
operating angle. z
CHECK vehicle ride
height is within limits.
REPAIR as necessary.
z Damaged or
worn front
suspension
components. z
CHECK for a loose
stabilizer bar, damaged
or loose strut/strut
bushings or loose or
worn ball joints.
INSPECT the steering
linkage for wear or
damage. REPAIR or
INSTALL new
components as
necessary.
z Shimmy—most
noticeable on
coast/deceleration. Also
hard steering condition z
Excessive
positive caster. z
CHECK the caster
alignment angle.
CORRECT as
necessary. REFER to
Section 204 - 00 .
Symptom Chart—
Tire Noise/Vibration Condition
Possible Sources Action
z Tire noise— hum/moan
at constant speeds z
Abnormal wear
patterns. z
SPIN the tire and CHECK
for tire wear. INSTALL a
new tire as necessary.
INSPECT for
damaged/worn suspension
components. CARRY OUT
wheel alignment.
z Tire noise— noise tone
lowers as the vehicle
speed is lowered z
Out-of- balance
tire. z
BALANCE the tire and
road test. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire noise — ticking
noise, changes with
speed z
Nail puncture or
stone in tire
tread. z
INSPECT the tire. REPAIR
as necessary.
z Wheel and tire—
vibration and noise
concern is directly
related to vehicle
speed and is not
affected by
acceleration, coasting
or decelerating z
Damaged or
worn tire. z
Go To Pinpoint Test J .
z Tire wobble or
shudder — occurs at
lower speeds z
Damaged wheel
bearings. z
SPIN the tire and CHECK
for abnormal wheel
bearing play or roughness.
ADJUST or INSTALL new
wheel bearings as
necessary. REFER to
Section 204 - 01 .
z Damaged wheel. zINSPECT the wheel for
damage. INSTALL a new
wheel as necessary.
REFER to Section 204 -Klj . 38 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

01 .
z Damaged or
worn suspension
components. z
INSPECT the suspension
components for wear or
damage. REPAIR as
necessary.
z Loose wheel
nuts. z
CHECK the wheel nuts.
TIGHTEN to specification.
REFER to Section 204 -
04 .
z Damaged or
uneven tire wear. z
SPIN the tire and CHECK
for abnormal tire wear or
damage. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire shimmy or
shake— occurs at
lower speeds z
Wheel/tire out of
balance. z
BALANCE the wheel/tire
assembly.
z Uneven tire wear. zCHECK for abnormal tire
wear. INSTALL a new tire
as necessary. REFER to
Section 204 - 04 .
z Excessive radial
runout of wheel
or tire. z
CARRY OUT a radial
runout test of the wheel
and tire. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Worn or
damaged wheel
studs or
elongated stud
holes. z
INSPECT the wheel studs
and wheels. INSTALL new
components as necessary.
REFER to Section 204 - 01
for the front wheels or
Section 204
- 02 for the rear
wheels.
z Excessive lateral
runout of the
wheel or tire. z
CARRY OUT a lateral
runout test of the wheel
and tire. CHECK the
wheel, tire and hub.
REPAIR or INSTALL new
components as necessary.
z Foreign material
between the
brake disc and
hub or in the
brake disc fins. z
CLEAN the mounting
surfaces of the brake disc
and hub. CHECK the
brake disc fins for material.
z High speed shake or
shimmy—occurs at
high speeds z
Excessive wheel
hub runout.
z Damaged or
worn tires.
z Damaged or
worn wheel
bearings.
z Worn or
damaged
suspension or
steering linkage
components.
z Brake disc or
drum imbalance. z
Go To Pinpoint Test K . Klj . 39 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

condition. It may not always be necessary to follow a pinpoint test to its conclusion. Carry out only the
steps necessary to correct the condition. Then, test the system for normal operation. Sometimes, it is
necessary to remove various vehicle components to gain access to the component requiring testing.
Reinstall all components after verifying system operation is normal.
PINPOINT TEST A: BRAKE VIBRATION/SHUDDER
Test Step Result / Action to Take
A1 ROAD TEST THE VEHICLE—
LIGHT BRAKING z
Check that the wheel and tires are correct for the vehicle.
Inspect the tires for abnormal wear patterns.
z Road test the vehicle. Warm the brakes by slowing the vehicle
a few times from 80– 32 km/h (50 to 20 mph) using light braking
applications. At highway speeds of 89–97 km/h (55- 60 mph),
apply the brake using a light pedal force.
z Is there a vibration/shudder felt in the steering wheel, seat
or brake pedal? Yes
GO to
A4 .
No
GO to A2 .
A2 ROAD TEST THE VEHICLE—
MODERATE TO HEAVY
BRAKING z
Road test the vehicle. At highway speeds of 89–97 km/h (55- 60
mph), apply the brake using a moderate to heavy pedal force.
z Is there a vibration/shudder? Yes
For vehicles with ABS,
GO to
A3 . For vehicles
with standard brakes,
GO to A4 .
No
Vehicle is OK. VERIFY
condition with customer.
TEST the vehicle for
normal operation. A3 NORMAL ACTUATION OF THE ABS SYSTEM DIAGNOSIS
z
During moderate to heavy braking, noise from the hydraulic
control unit (HCU) and pulsation in the brake pedal can be
observed. Pedal pulsation coupled with noise during heavy
braking or on loose gravel, bumps, wet or snowy surfaces is
acceptable and indicates correct functioning of the ABS
system. Pedal pulsation or steering wheel nibble, (frequency is
proportioned to the vehicle speed) indicates a concern with a
brake or suspension component.
z Is the vibration/shudder vehicle speed sensitive? Yes
GO to
A5 .
No
The brake system is
operating correctly. A4 APPLICATION OF THE PARKING BRAKE
z
NOTE: Begin at the front of the vehicle unless the vibration or
shudder has been isolated to the rear.
z This test is not applicable to vehicles with drum- in-hat type
parking brakes. For vehicles with drum- in-hat parking brakes,
proceed to the next test. For all other vehicles, apply the
parking brake to identify if the problem is in the front or rear
brake. At highway speeds of 89–97 km/h (55- 60 mph), lightly
apply the parking brake until the vehicle slows down. Release
the parking brake immediately after the test.
z Is there a vibration/shudder? Yes
GO to
A7 .
No
GO to A5 .
A5 CHECK THE FRONT WHEEL BEARINGS
z
Check the front wheel bearings. Refer to Wheel Bearing Check in this section.
z Are the wheel bearings OK? Yes
GO to
A6 . Klj . 48 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST C: ACCESSORY DRIVE BEARING HOOT
PINPOINT TEST D: POWER STEERING MOAN
PINPOINT TEST E: ENGINE DRIVEN COOLING FAN MOAN operating correctly?
No
INSTALL a new valve lifter/lash adjuster
(s). TEST the system for normal
operation.
Test Step Result / Action to Take
C1 CHECK THE IDLER AND TENSIONER
PULLEY BEARINGS z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Place an EngineEAR probe directly on the
pulley center post or bolt to verify which
bearing is making the noise.
z Key in OFF position.
z Is either bearing making the noise? Yes
INSTALL a new pulley/idler. CARRY OUT the
Vehicle Cold Soak Procedure and TEST the
system for normal operation.
No
CONDUCT a diagnosis on other suspect
accessory drive components.
Test Step Result / Action to Take
D1 CHECK THE POWER STEERING
SYSTEM z
Carry out the Vehicle Cold Soak
Procedure in this section.
z Key in START position.
z Turn the steering wheel while the noise
is occurring and listen for changes in
sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
GO to
D2 .
No
CONDUCT a diagnosis on other suspect
accessory drive components. D2 VERIFY THE SOURCE
z
Key in START position.
z Place an EngineEAR probe near the
power steering pump/reservoir while the
noise is occurring. While an assistant
turns the steering wheel, listen for
changes in sound pitch or loudness.
z Key in OFF position.
z Does the sound pitch or loudness
change while turning the steering
wheel? Yes
VERIFY that the supply tube to the pump is
unobstructed. CHECK the fluid condition and
level. DRAIN the fluid and REFILL. CARRY
OUT the Vehicle Cold Soak Procedure and
TEST the system for normal operation. REFER
to Section 211
- 02 .
No
Normal system operation. Test Step Result / Action to Take
E1 CHECK THE ENGINE DRIVEN COOLING
FAN AFTER A COLD SOAK Klj . 51 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST G: ENGINE TICKING, KNOCKING OR CONTINUOUS
RATTLE
PINPOINT TEST H: FRONT SUSPENSION NOISE CONDUCT diagnosis of
other suspect components.
Test Step Result / Action to Take
G1 CHECK FOR NOISE AT THE VALVE COVERS
AND THE FRONT COVERS (OHC ENGINES) z
Carry out the Vehicle Cold Soak Procedure in
this section.
z Key in START position.
z NOTE: For a short- duration ticking noise,
multiple engine starts may be necessary.
z Using an EngineEAR, listen closely at the valve
covers and the front covers (OHC engines) by
placing the probe near the surface of the valve
cover and then on the surface front cover.
z Key in OFF position.
z Is the noise source apparent? Yes
REMOVE the appropriate cover and
INSPECT for loose, worn/broken
components. REPAIR as necessary.
TEST the system for normal operation.
No
GO to
G2 .
G2 CHECK FOR NOISE AT THE CYLINDER
BLOCK z
Key in START position.
z Using an EngineEAR, listen closely at the
cylinder block by placing a probe on or near
each freeze plug.
z Key in OFF position.
z Is the noise source apparent? Yes
REPAIR or INSTALL new components
as necessary.
No
GO to
G3 .
G3 CHECK FOR NOISE WHILE DISCONNECTING
EACH FUEL INJECTOR ELECTRICAL
CONNECTOR, ONE AT A TIME z
Key in START position.
z Disconnect each fuel injector electrical
connector, one at a time, to decrease piston
force and listen for the noise.
z Key in OFF position.
z Is the noise reduced or eliminated? Yes
INSTALL a new fuel injector. TEST the
system for normal operation.
No
INSPECT accessory drive system or the
transmission as a possible source.
Test Step Result / Action to Take
H1 ROAD TEST THE VEHICLE
z
Test drive the vehicle.
z NOTE: An assistant will be needed for this road test.
z During the road test, drive the vehicle over a rough road.
Using ChassisEARs, determine from which
area/component the noise is originating.
z Is there a squeak, creak or rattle noise? Yes
GO to
H2 .
No
The suspension system is
OK. CONDUCT a diagnosis
on other suspect systems. H2 INSPECT THE STEERING SYSTEM
Yes Klj . 53 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST I: REAR SUSPENSION NOISE z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the steering system for wear or damage. Carry out a
steering linkage test. Refer Section 211 - 00 .
z Inspect the tire wear pattern. Refer to Tire Wear Patterns
chart in this section.
z Are the steering components worn or damaged? REPAIR the steering
system. INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H3 .
H3 FRONT SHOCK ABSORBER/STRUT CHECK
z
Check the front shock absorbers/strut mounts for loose
bolts or nuts.
z Check the front shock absorbers/struts for wear or damage.
Carry out a "bounce test".
z Are the front shock absorbers/struts loose or
damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new front
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
H4 .
H4 CHECK THE FRONT SPRINGS
z
Check the front spring and front spring mounts/brackets for
wear or damage.
z Are the front springs or spring mounts/brackets worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H5 .
H5 CHECK THE CONTROL ARMS/RADIUS ARMS
z
Inspect the control arm bushings for wear or damage.
z Inspect for twisted or bent control/radius arm.
z Are the control/radius arms damaged or worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
H6 .
H6 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step Result / Action to Take Klj . 54 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Take
J1 ROAD TEST THE VEHICLE
z
NOTE: Wheel or tire vibrations felt in the steering wheel are most
likely related to the front wheel or tire. Vibration felt through the
seat are most likely related to the rear wheel or tire. This may not
always be true, but it can help to isolate the problem to the front
or rear of the vehicle.
z Test drive the vehicle at different speed ranges.
z During the road test, if the vibration can be eliminated by placing
the vehicle in neutral or is affected by the speed of the engine,
the cause is not the wheels or tires.
z Is there a vibration and noise? Yes
GO to
J2 .
No
The wheel and tires
are OK. CONDUCT a
diagnosis on other
suspect systems. J2 CHECK THE FRONT WHEEL BEARINGS
z
Check the front wheel bearings. Refer to Wheel Bearing Check in
this section.
z Are the wheel bearings OK? Yes
GO to
J3 .
No
INSPECT the wheel
bearings. ADJUST or
REPAIR as necessary.
TEST the system for
normal operation. J3 INSPECT THE TIRES
z
Check the tires for missing weights.
z Check the wheels for damage.
z Inspect the tire wear pattern. Refer to the Tire Wear Patterns
chart in this section.
z Do the tires have an abnormal wear pattern? Yes
CORRECT the
condition that caused
the abnormal wear.
INSTALL new tire(s).
TEST the system for
normal operation.
No
GO to
J4 .
J4 TIRE ROTATION
z
Spin the tires slowly and watch for signs of lateral runout.
z Spin the tires slowly and watch for signs of radial runout. Yes
GO to
J5 .
No
CHECK the wheel and
tire balance.
CORRECT as
necessary. TEST the
system for normal
operation. Klj . 56 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...