2003 FORD MUSTANG steering

z
If equipped, inspect automatic transmission fluid level with dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new cabin air filter.
z If filled with green engine coolant, change coolant.
224,000 Km (140,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
232,000 Km (145,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
240,000 Km (150,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z If filled with yellow engine coolant, change coolant or at 8 years, whichever comes first.
z Change automatic transmission/transaxle fluid and filter.
z Change rear axle lubricant on all rear wheel (RWD) vehicles.
z Install a new accessory drive belt(s) (if a new belt has not been installed within the last 100,000
miles).
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: If vehicle is registered in California, the California Air Resources Board
(CARB) has determined that failure to install a new fuel filter at this interval will not nullify the emission
warranty or limit recall liability prior to completion of the vehicle's useful life. It is, however
recommended that maintenance checks be carried out and recorded at the indicated intervals.
Additional checks for natural gas and propane vehicles include inspecting fuel tanks, as well as
draining and installing a new filter. Klj . 9 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

The angle of the wheel in relation to the true vertical as measured looking from the front of the vehicle.
Camber is positive when the wheel angle is offset so that the top of the wheel is positioned away from
the vehicle.
Caster
The angle of the steering knuckle in relation to the true vertical as measured looking from the side of
the vehicle.
Chatter
A pronounced series of rapidly repeating rattling or clicking sounds.
Chirp
A short-duration high-
pitched noise associated with a slipping drive belt.
Chuckle
A repetitious low- pitched sound. A loud chuckle is usually described as a knock.
Click
A sharp, brief, non- resonant sound, similar to actuating a ball point pen. Item Description
1 Positive caster
2 True vertical
3 Steering axis Klj . 3 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Lateral runout means measuring the movement or "wobble" of a wheel or tire at the sidewall. Radial
runout means measuring the out-of-
round at the tread surface.
Rustling
Intermittent sound of varying frequency (100- 2000 Hz), sounds similar to shuffling through leaves.
Shake
A low- frequency vibration (5-20 Hz), usually with visible component movement. Usually relates to tires,
wheels, brake drums or brake discs if it is vehicle speed sensitive, or engine if it is engine speed
sensitive. Also referred to as a shimmy or wobble.
Shimmy
An abnormal vibration or wobbling, felt as a side- to-side motion of the steering wheel in the driveshaft
rotation. Also described as waddle.
Shudder
A low- frequency vibration that is felt through the steering wheel or seat during light brake application.
Slap
A resonance from flat surfaces, such as safety belt webbing or door trim panels.
Slip Yoke/Slip Spline
The driveshaft coupling that allows length changes to occur while the suspension articulates and while
the driveshaft rotates.
Squeak
A high- pitched transient sound, similar to rubbing fingers against a clean window.
Squeal
A long- duration, high- pitched noise.
Static Balance
The equal distribution of weight around the wheel. Statically unbalanced wheel and tire assemblies can
cause a bouncing action called wheel tramp. This condition will eventually cause uneven tire wear.
Tap
A light, rhythmic, or intermittent hammering sound, similar to tapping a pencil on a table edge.
Thump
A dull beat caused by two items striking together. Tick Klj . 9 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

WOT
The acronym for wide open throttle is WOT.
Tools and Techniques
Electronic Vibration Analyzer (EVA)
The EVA is a hand-
held electronic diagnostic tool which will assist in locating the source of
unacceptable vibrations. The vibration sensor can be remotely mounted anywhere in the vehicle for
testing purposes. The unit displays the three most common vibration frequencies and their
corresponding amplitudes simultaneously. A bar graph provides a visual reference of the relative
signal strength (amplitude) of each vibration being displayed and its relative G force. The keypad is
arranged to make the EVA simple to program and use. Some of the functions include the ability to
average readings as well as record, play back and freeze readings. The EVA has a strobe balancing
function that can be used to detect imbalance on rotating components such as a driveshaft or engine
accessories.
The EVA allows for a systematic collection of information that is necessary to accurately diagnose and
repair NVH problems. For the best results, carry out the test as follows:
a. Test drive the vehicle with the vibration sensor inside the vehicle.
b. Place the sensor in the vehicle according to feel. „If the condition is felt through the steering wheel, the source is most likely in the front of
the vehicle.
„ A vibration that is felt in the seat or floor only will most likely be found in the driveline,
drive axle or rear wheels and tires.
c. Record the readings. Also note when the condition begins, when it reaches maximum intensity, and if it tends to diminish above/below a certain speed.
„Frequencies should be read in the "average" mode. Item Description
1 EVA screen
2 Frequency mode displayed in rpm or Hz
3 Active sensor input (A or B)
4 Current active mode
5 G force indicators or the strongest frequencies in descending strength of each vibration
6 Strength of each vibration
7 Frequency in rpm/Hz of each vibration Klj . 11 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

„
Frequencies have a range of plus or minus 2. A reading of 10 Hz can be displayed as an
8 Hz through 12 Hz.
d. Place the vibration sensor on or near the suspect area outside the vehicle.
e. Continue the road test, driving the vehicle at the speed the symptom occurs, and take another reading.
f. Compare the readings.
„A match in frequency indicates the problem component or area.
„ An unmatched test could indicate the concern is caused by the engine, torque converter,
or engine accessory. Use the EVA in the rpm mode and check if concern is rpm related.
„ Example: A vibration is felt in the seat. Place the sensor on the console. Record the
readings. Place the vibration sensor on the rear axle. Compare the readings. If the
frequencies are the same, the axle is the problem component.
Vibrate Software®
Vibrate Software® ( Rotunda tool number 215- 00003) is a diagnostic aid which will assist in pinpointing
the source of unacceptable vibrations. The engine's crankshaft is the point of reference for vibration
diagnosis. Every rotating component will have an angular velocity that is faster, slower, or the same as
the engine's crankshaft. Vibrate Software® calculates the angular velocity of each component and
graphically represents these velocities on a computer screen and on a printed vibration worksheet.
The following steps outline how Vibrate Software® helps diagnose a vibration concern:
zEnter the vehicle information. Vibrate will do all the calculations and display a graph showing
tire, driveshaft and engine vibrations.
z Print a Vibration Worksheet graph. The printed graph is to be used during the road test.
z Road test the vehicle at the speed where the vibration is most noticeable. Record the vibration
frequency (rpm) and the engine rpm on the worksheet graph. The point on the graph where the
vibration frequency (rpm) reading and the engine rpm reading intersect indicates the specific
component group causing the concern.
„An EVA or equivalent tool capable of measuring vibration frequency and engine rpm will
be needed.
z Provide pictures of diagnostic procedures to aid in testing components.
Combination EngineEAR/ChassisEAR
An electronic listening device used to quickly identify noise and the location under the chassis while
the vehicle is being road tested. The ChassisEARs can identify the noise and location of
damaged/worn wheel bearings, CV joints, brakes, springs, axle bearings or driveshaft carrier bearings.
EngineEAR Basic Unit
An electronic listening device used to detect even the faintest noises. The EngineEARs can detect the
noise of damaged/worn bearings in generators, water pumps, A/C compressors and power steering
pumps. They are also used to identify noisy lifters, exhaust manifold leaks, chipped gear teeth and for
detecting wind noise. The EngineEAR has a sensing tip, amplifier, and headphones. The directional
sensing tip is used to listen to the various components. Point the sensing tip at the suspect component
and adjust the volume with the amplifier. Placing the tip in direct contact with a component will reveal
structure-borne noise and vibrations, generated by or passing through, the component. Various
volume levels can reveal different sounds.
Ultrasonic Leak Detector
The Ultrasonic Leak Detector is used to detect wind noises caused by leaks and gaps in areas where
there is weather- stripping or other sealing material. It is also used to identify A/C leaks, vacuum leaks Klj . 12 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
It may be necessary to have the customer ride along or drive the vehicle to point out the
concern. During the road test, take into consideration the customer's driving habits and the driving
conditions. The customer's concern just may be an acceptable operating condition for that vehicle.
The following is a brief overview of each test in the order in which it appears. A review of this
information helps to quickly identify the most appropriate process necessary to make a successful
diagnosis. After reviewing this information, select and carry out the appropriate test(s), proceeding to
the next step of this process.
zThe Slow Acceleration Test is normally the first test to carry out when identifying an NVH
concern, especially when a road test with the customer is not possible.
z The Heavy Acceleration Test helps to determine if the concern is torque- related.
z The Neutral Coast Down Speed Test helps to determine if the concern is vehicle speed- related.
z The Downshift Speed Test helps to determine if the concern is engine speed- related.
z The Steering Input Test helps to determine how the wheel bearings and other suspension
components contribute to a vehicle speed- related concern.
z The Brake Test helps to identify vibrations or noise that are brake related.
z The Road Test Over Bumps helps isolate a noise that occurs when driving over a rough or
bumpy surface.
z The Engine Run- Up Tests consist of the Neutral Run- Up Test and the Engine Load Test. These
tests help to determine if the concern is engine speed- related.
z The Neutral Run- Up Test is used as a follow- up test to the Downshift Speed Test when the
concern occurs at idle.
z The Engine Load Test helps to identify vibration/noise sensitive to engine load or torque. It also
helps to reproduce engine speed- related concerns that cannot be duplicated when carrying out
the Neutral Run- Up Test or the Neutral Coast Down Test.
z The Engine Accessory Test helps to locate faulty belts and accessories that cause engine
speed- related concerns.
z The Vehicle Cold Soak Procedure helps to identify concerns occurring during initial start- up and
when an extended time lapse occurs between vehicle usage.
Slow Acceleration Test
To carry out this test, proceed as follows:
zSlowly accelerate to the speed where the reported concern occurs. Note the vehicle speed, the
engine rpm and, if possible, determine the vibration frequency.
z Attempt to identify from what part of the vehicle the concern is coming.
z Attempt to identify the source of the concern.
z Proceed as necessary.
Heavy Acceleration Test
To carry out this test, proceed as follows:
zAccelerate hard from 0- 64 km/h (0-40 mph).
z Decelerate in a lower gear.
z The concern is torque related if duplicated while carrying out this test.
z Proceed as necessary. Klj . 6 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Neutral Coast Down Speed Test
To carry out this test, proceed as follows:
zDrive at a higher rate of speed than where the concern occurred when carrying out the Slow
Acceleration Test.
z Place the transmission in NEUTRAL and coast down past the speed where the concern occurs.
z The concern is vehicle speed- related if duplicated while carrying out this test. This eliminates
the engine and the torque converter as sources.
z If the concern was not duplicated while carrying out this test, carry out the Downshift Speed
Test to verify if the concern is engine speed related.
z Proceed as necessary.
Downshift Speed Test
To carry out this test, proceed as follows:
zShift into a lower gear than the gear used when carrying out the Slow Acceleration Test.
z Drive at the engine rpm where the concern occurs.
z The concern is engine speed related if duplicated while carrying out this test. This eliminates the
tires, wheels, brakes and the suspension components as sources.
z If necessary, repeat this test using other gears and NEUTRAL to verify the results.
z Proceed as necessary.
Steering Input Test
To carry out this test, proceed as follows:
zDrive at the speed where the concern occurs, while making sweeping turns in both directions.
z If the concern goes away or gets worse, the wheel bearings, hubs, U- joints (contained in the
axles of 4WD applications), and tire tread wear are all possible sources.
z Proceed as necessary.
Brake Test
To carry out this test, proceed as follows:
zWarm the brakes by slowing the vehicle a few times from 80–32 km/h (50–20 mph) using light
braking applications. At highway speeds of 89–97 km/h (50– 60 mph), apply the brake using a
light pedal force.
z Accelerate to 89–97 km/h (55–60 mph).
z Lightly apply the brakes and slow the vehicle to 30 km/h (20 mph).
z A brake vibration noise can be felt in the steering wheel, seat or brake pedal. A brake noise can
be heard upon brake application and diminish when the brake is released.
Road Test Over Bumps
To carry out this test, proceed as follows: Klj . 7 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

„
Loudness proportional to vehicle speed. Low- frequency noise at high
speeds, noise and loudness increase with speed. GO to Symptom Chart —
Driveline Noise/Vibration .
„ A low- pitched noise (drumming). GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of acceleration or
deceleration. GO to Symptom Chart — Tire Noise/Vibration .
„ Noise varies with wind/vehicle speed and direction. GO to Symptom Chart — Air Leak and Wind Noise .
„ Related to engine speed.
„Noise varies with engine rpm. GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of engine speed
(rpm).
2. Acceleration
„Wide open throttle (WOT)
„Engine induced contact between components. Inspect and repair as
necessary.
„ Noise is continuous throughout WOT. Exhaust system or engine ground
out. GO to Symptom Chart — Engine Noise/Vibration .
„ Light/moderate acceleration
„Tip- in moan. Engine/exhaust noise. GO to Symptom Chart — Engine
Noise/Vibration .
„ Knock-type noise. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline shudder. GO to Symptom Chart — Driveline Noise/Vibration .
„ Engine vibration. GO to Symptom Chart — Engine Noise/Vibration .
3. Turning noise. GO to Symptom Chart — Steering Noise/Vibration .
4. Braking
„Clicking sound is signaling ABS is active. Acceptable ABS sound.
„ A continuous grinding/squeal. GO to Symptom Chart — Brake Noise/Vibration .
„ Brake vibration/shudder. GO to Symptom Chart — Brake Noise/Vibration .
5. Clutching
„A noise occurring during clutch operation. GO to Symptom Chart — Transmission
(Manual) and Transfer Case Noise/Vibration .
„ Vibration. GO to Symptom Chart — Transmission (Manual) and Transfer Case
Noise/Vibration .
6. Shifting
„Noise or vibration condition related to the transmission (automatic). GO to
Symptom Chart — Transmission (Automatic) Noise/Vibration .
„ Noise or vibration related to the transmission (manual). GO to Symptom Chart —
Transmission (Manual) and Transfer Case Noise/Vibration .
7. Engaged in four- wheel drive. GO to Symptom Chart — Transmission (Manual) and
Transfer Case Noise/Vibration .
8. Cruising speeds
„Accelerator pedal vibration. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline vibration. GO to Symptom Chart — Driveline Noise/Vibration .
„ A shimmy or shake. GO to Symptom Chart — Tire Noise/Vibration .
9. Driving at low/medium speeds Klj . 11 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...