2003 FORD MUSTANG manual transmission

IN-
VEHICLE REPAIR
Seal
Removal 1. With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. CAUTION: Index- mark the driveshaft flange and pinion flange, and the driveshaft
slip yoke and transmission output shaft.
Remove the driveshaft. For additional information, refer to Section 205 - 01 .
3. Using the special tools, remove the extension housing fluid seal.
Installation 1. Using the special tool, install the extension housing fluid seal.
SECTION 308-
03B: Manual Transaxle/Transmission — TR3650 2003 Mustang Workshop Manual Special Tool(s)
Installer, Transmission
Extension Housing Oil Seal
308-
227 (T94P-7657- A) Slide Hammer
100-
001 (T50T-100- A) Remover, Bushing
307-
001 (TOOL- 1175-AC) or
Equivalent Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

2.
CAUTION: Align the index marks.
Install the driveshaft. For additional information, refer to Section 205 - 01 .
3. Check the transmission fluid level, add fluid if necessary.
4. Lower the vehicle. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Gearshift Lever and Boot
Removal and Installation 1. Remove the gearshift lever knob.
2. Remove the console panel gearshift plate. Lift the gearshift lever boot over the gearshift lever.
3. Remove the bolts and the shift lever.
SECTION 308-
03B: Manual Transaxle/Transmission — TR3650 2003 Mustang Workshop Manual Material
Item Specification
Clear Silicone Rubber
D6AZ-
19562- AA or equivalent ESB-
M4G92- A Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Output Shaft Speed (OSS) Sensor
Removal and Installation 1. With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Disconnect the electrical connector.
3. Remove the output shaft speed (OSS) sensor.
4. To install, reverse the removal procedure.
SECTION 308-
03B: Manual Transaxle/Transmission — TR3650 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

REMOVAL
Transmission
1. Disconnect the battery ground cable. For additional information, refer to Section 414 - 01 .
2. Remove the gearshift lever knob.
3. Remove the console panel gearshift plate. Lift the gearshift lever boot over the gearshift lever.
4. Remove the bolts and the shift lever.
5. With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100 - 02 .
6. Remove the dual converter H- pipe. For additional information, refer to Section 309 - 00 .
7. CAUTION: Index- mark the driveshaft flange and pinion flange, and the driveshaft slip yoke and transmission output shaft. SECTION 308-
03B: Manual Transaxle/Transmission — TR3650 2003 Mustang Workshop Manual Klj . 1 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

Remove the driveshaft. For additional information, refer to
Section 205 - 01 .
8. Disconnect the reversing lamp switch electrical connector. Disconnect the wiring harness from the transmission.
9. Remove the starter motor. For additional information, refer to Section 303 - 06 .
10. Remove the bolts.
11. Remove the starter solenoid nuts and position the wires aside. Klj . 2 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

12. Remove the starter motor.
13. Disconnect the OSS sensor electrical connector. Disconnect the wiring harness from the
transmission.
14. Remove the bolt and the clutch release lever cover.
15. CAUTION: To prevent component damage, do not depress the clutch pedal with the
transmission removed.
Disengage the clutch release cable from the clutch release fork.
16. Remove the clutch cable retainer and remove the clutch cable from the transmission. Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

17. If transmission disassembly is necessary, drain the transmission fluid.
18. Position a transmission jack and support the transmission.
19. Remove the bolts and the transmission crossmember.
20. Remove the bolts. Klj . 4 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...