2003 FORD MUSTANG check oil

6. Carry out an oil consumption test:
a. Drain the engine oil, remove the oil bypass filter (6714) and refill with one liter (quart) less than
the recommended amount.
b. Run the engine for three minutes (10 minutes if cold), and allow the oil to drain back for at least five minutes with the vehicle on a level surface.
c. Remove oil level dipstick and wipe clean. (Do not wipe with anything contaminated with silicone compounds.) Reinstall the oil level dipstick, being sure to seat it firmly in the oil level indicator
tube (6754). Remove the oil level dipstick and draw a mark on the back (unmarked) surface at
the indicated oil level. This level should be about the same as the MIN or ADD mark on the face
of the oil level dipstick.
d. Add one liter (quart) of oil. Restart the engine and allow to idle for at least two minutes. Shut off the engine and allow the oil to drain back for at least five minutes. Mark the oil level dipstick,
using the procedure above.
e. Record the vehicle mileage. f. Instruct the customer to drive the vehicle as usual and perform the following:
„Check the oil level regularly at intervals of 160 to 240 km (100- 150 miles).
„ Return to the service point when the oil level drops below the lower (MIN or ADD) mark
on the oil level dipstick.
„ Add only full liters (quarts) of the same oil in an emergency. Note the mileage at which
the oil is added.
g. Check the oil level under the same conditions and at the same location as in Steps 6c and 6d.
„Measure the distance from the oil level to the UPPER mark on the oil level dipstick and
record.
„ Measure the distance between the two scribe marks and record.
„ Divide the first measurement by the second.
„ Divide the distance driven during the oil test by the result. This quantity is the
approximate oil consumption rate in kilometers per liter or in miles per quart.
h. If the oil consumption rate is unacceptable, go to Step 7.
7. Check the positive crankcase ventilation (PCV) system. Make sure the system is not plugged.
8. Check for plugged oil drain- back holes in the cylinder heads and cylinder block.
9. If the condition still exists after performing the above steps, go to Step 10.
10. Perform a cylinder compression test or perform a cylinder leak detection test with Engine Cylinder Leak Detection/Air Pressurization Kit. This can help determine the source of oil
consumption such as valves, piston rings or other areas.
11. NOTE: After determining if new parts should be installed, make sure correct parts are used.
Check valve guides for excessive guide clearance. Install new all valve stem seals (6571) after
verifying valve guide clearance.
12. Worn or damaged internal engine components can cause excessive oil consumption. Small deposits of oil on the tips of spark plugs can be a clue to internal oil consumption. If internal oil
consumption still persists, proceed as follows:
a. Remove the engine from the vehicle and place it on an engine work stand. Remove the intake manifolds (9424), cylinder heads, oil pan (6675) and oil pump (6600).
b. Check piston ring clearance, ring gap and ring orientation. Repair as necessary.
c. Check for excessive bearing clearance. Repair as necessary.
13. Repeat the oil consumption test (Step 6) to confirm the oil consumption concern has been resolved. Klj . 10 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Engines need oil to lubricate the following internal components:
zcylinder block cylinder walls
z pistons and piston, pin and rings (6102)
z intake and exhaust valve stems
z intake and exhaust valve guides
z all internal engine components
When the pistons move downward, a thin film of oil is left on the cylinder walls. As the vehicle is
operated, some oil is also drawn into the combustion chambers past the intake and exhaust valve
stem seals and burned.
The following is a partial list of conditions that can affect oil consumption rates:
zengine duty cycle
z operator driving habits
z ambient temperature
z quality and viscosity of the oil
Operation under varying conditions can frequently be misleading. A vehicle that has been run for
several thousand miles on short trips or in below- freezing ambient temperatures may have consumed
a "normal" amount of oil. However, when checking the engine oil level, it may measure up to the FULL
or MAX on the oil level dipstick due to dilution (condensation and fuel) in the engine crankcase. The
vehicle might then be driven at high speeds on the highway where the condensation and fuel boil off.
The next time the engine oil is checked, it may appear that a liter (quart) of oil was used in about 160
km (100 miles). This perceived 160 km (100 miles) per liter (quart) oil consumption rate causes
customer concern even though the actual overall oil consumption rate is about 2,400 km (1,500 miles)
per liter (quart).
Make sure the selected engine oil meets the current recommended API performance category with
SAE viscosity grade as shown in the vehicle Owner's Guide. It is also important that the engine oil is
changed at the intervals specified. Refer to the vehicle Owner's Guide.
Oil Pressure Test
1. Disconnect and remove the oil pressure sensor (9278) from the engine.
2. Connect the Oil Pressure Gauge to the oil pressure sender oil galley port.
3. Run the engine until normal operating temperature is reached.
4. Run the engine at the specified rpm and record the gauge reading.
5. The oil pressure should be within specifications; refer to the specification chart in the appropriate engine section.
6. If the pressure is not within specification, check the following possible sources: zinsufficient oil
z oil leakage
z worn or damaged oil pump
z oil pump screen cover and tube (6622)
z excessive main bearing clearance Klj . 13 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
excessive connecting rod bearing clearance
Valve Train Analysis— Engine Off—Valve Cover Removed
Check for damaged or severely worn parts and correct assembly. Make sure correct parts are used
with the static engine analysis as follows.
Valve Train Analysis— Engine Off, Rocker Arm
z Check for loose mounting bolts, studs and nuts.
z Check for plugged oil feed in the rocker arms (6564) or cylinder head.
Valve Train Analysis— Engine Off, Camshaft Roller Followers and Hydraulic Lash Adjusters,
Overhead Camshaft
zCheck for loose mounting bolts on camshaft carriers.
z Check for plugged oil feed in the camshaft roller followers, lash adjusters or cylinder heads.
Valve Train Analysis— Engine Off, Camshaft— Engines
z Check for broken or damaged parts.
Valve Train Analysis— Engine Off, Push Rods
z Check for bent push rods (6565) and restricted oil passage.
Valve Train Analysis— Valve Springs
z Check for broken or damaged parts.
Valve Train Analysis— Engine Off, Valve Spring Retainer and Valve Spring Retainer Keys
z Check for correct seating of the valve spring retainer key (6518) on the valve stem and in valve
spring retainer (6514).
z Check for correct seating on the valve stem.
Valve Train Analysis— Engine Off, Valves and Cylinder Head
z Check for plugged oil drain back holes.
z Check for worn or damaged valve tips.
z Check for missing or damaged guide- mounted valve stem seal.
z Check collapsed valve tappet gap.
z Check installed valve spring height.
z Check for missing or worn valve spring seats.
z Check for plugged oil metering orifice in cylinder head oil reservoir (if equipped).
Static checks (engine off) are to be made on the engine prior to the dynamic procedure. Klj . 14 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Valve Train Analysis—
Engine Running
z Start the engine and, while idling, check for correct operation of all parts. Check the following:
Valve Train Analysis— Engine Running, Valves and Cylinder Head
z Check for plugged oil drain back holes.
z Check for missing or damaged valve stem seals or guide mounted valve stem seals.
z Check for a plugged oil metering orifice in the cylinder head oil reservoir (4.6L engine only).
If insufficient oiling is suspected, check oil passages for blockage, then accelerate the engine to 1,200
rpm with the transmission in NEUTRAL and the engine at normal operating temperature. Oil should
spurt from the rocker arm oil holes such that valve tips and camshaft roller followers are well oiled.
With the valve covers (6582) off, some oil splash may overshoot camshaft roller followers.
Valve Train Analysis— Engine Running, Camshaft Lobe Lift— OHC Engines
Check the lift of each camshaft lobe in consecutive order and make a note of the readings. 1. Remove the valve covers.
2. Remove the spark plugs.
3. Install the Dial Indicator Gauge with Holding Fixture so the rounded tip of indicator is on top of the camshaft lobe and on the same plane as the valve tappet.
4. Rotate the crankshaft using a breaker bar and socket attached to the crankshaft pulley retainer bolt. Rotate the crankshaft until the base circle of the camshaft lobe is reached.
5. Zero the dial indicator. Continue to rotate the crankshaft until the (1) high- lift point of the
camshaft lobe is in the fully- raised position (highest indicator reading).
6. To check the accuracy of the original indicator reading, continue to rotate crankshaft until the (2) base circle is reached. The indicator reading should be zero. If zero reading is not obtained,
repeat Steps 1 through 6.
7. NOTE: If the lift on any lobe is below specified service limits, install a new camshaft, and new
camshaft roller followers.
Remove the Dial Indicator Gauge with Holding Fixture.
8. Install the spark plugs. Klj . 15 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
incorrectly functioning valve tappet
z air in lubrication system
z excessive valve guide wear
z low oil pressure
Excessive collapsed valve tappet gap can be caused by loose rocker arm seat bolts/nuts, incorrect
initial adjustment or wear of valve tappet face, or worn roller valve tappets, push rod (6565), rocker
arm (6564), rocker arm seat or valve tip. With valve tappet collapsed, check gap between the valve tip
and the rocker arm to determine if any other valve train parts are damaged, worn or out of adjustment.
An incorrectly functioning valve tappet can be sticking, caused by contaminants or varnish inside the
tappet. The tappet can have a check valve that is not functioning correctly, which can be caused by an
obstruction, such as dirt or chips that prevent the check valve from closing, or a broken check valve
spring. A tappet with a leakdown time out of specification can cause tappet noise. If no other cause for
noisy valve tappets can be found, the leakdown rate should be checked and new valve tappets
installed if found to be out of specification.
Assembled valve tappets can be tested with Hydraulic Tappet Leakdown Tester to check the leakdown
rate. The leakdown rate specification is the time in seconds for the plunger to move a specified
distance while under a 22.7 kg (50 lb) load.
Air bubbles in the lubrication system will prevent the valve tappet from supporting the valve spring
load. This can be caused by too high or too low an oil level in the oil pan or by air being drawn into the
system through a hole, crack or leaking gasket on the oil pump screen cover and tube. Klj . 17 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Piston Inspection
CAUTION: Do not use a caustic cleaning solution or a wire brush to clean the pistons or
damage can occur.
1. Clean and inspect the (1) ring lands, (2) skirts, (3) pin bosses, and the (4) tops of the pistons. If wear marks, scores or glazing is found on the piston skirt, check for a bent or twisted
connecting rod.
2. Use the Piston Ring Groove Scraper to clean the piston ring grooves. zMake sure the oil ring holes are clean.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Special Tool(s)
Scraper, Piston Ring Groove
303-
D033 (D81L-6002- D) or
equivalent Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Spark Plug —
Inspection
1. Inspect the spark plug for a bridged gap. zCheck for deposit build- up closing the gap between the electrodes. Deposits are caused
by oil or carbon fouling.
z Clean the spark plug.
2. Check for oil fouling. zCheck for wet, black deposits on the insulator shell bore electrodes, caused by excessive
oil entering the combustion chamber through worn rings and pistons, excessive valve- to-
guide clearance or worn or loose bearings.
z Correct the oil leak concern.
z Install a new spark plug.
3. Inspect for carbon fouling. Look for black, dry, fluffy carbon deposits on the insulator tips, exposed shell surfaces and electrodes, caused by a spark plug with an incorrect heat range,
dirty air cleaner, too rich a fuel mixture or excessive idling.
zClean the spark plug.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Inspect for normal burning.
zCheck for light tan or gray deposits on the firing tip.
5. Inspect for pre- ignition, identified by melted electrodes and a possibly damaged insulator.
Metallic deposits on the insulator indicate engine damage. This may be caused by incorrect
ignition timing, wrong type of fuel or the unauthorized installation of a heli- coil insert in place of
the spark plug threads.
zInstall a new spark plug.
6. Inspect for overheating, identified by a white or light gray spots and with bluish- burnt
appearance of electrodes. This is caused by engine overheating, wrong type of fuel, loose spark
plugs, spark plugs with an incorrect heat range, low fuel pump pressure or incorrect ignition
timing.
zInstall a new spark plug. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...