2003 FORD MUSTANG check oil

z
Excessive front or
rear toe (rapid inner
or outer edge
wear). z
CHECK the wheel alignment.
ADJUST as necessary.
z Excessive negative
or positive camber
(rapid inner or outer
edge wear). z
CHECK the wheel alignment.
ADJUST as necessary.
z Tires out of balance
(tires cupped or
dished). z
BALANCE tires.
z Rough ride zStrut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Front coil springs or
rear springs (5560). z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Shimmy or
wheel tramp z
Loose wheel nut(s). zTIGHTEN to specification.
REFER to Section 204 - 04 .
z Loose front
suspension
fasteners. z
TIGHTEN to specification.
REFER to Section 204 - 01 .
z Front wheel bearing
(s). z
REFER to Wheel Bearing Inspection in this section.
z Wheel or tire
runout. z
REFER to Section 204 - 04 .
z Tire flatspotting. zREFER to Section 204 - 04 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Loose, worn or
damaged ball joint
(s). z
GO to the Ball Joint Inspection
component test in this section.
z Loose, worn or
damaged steering
components. z
REFER to Section 211 - 00 .
z Front wheel
alignment. z
CHECK the wheel alignment.
ADJUST as necessary.
z Sticky steering,
poor returnability z
Ball joints. zGO to the Ball Joint Inspection
component test in this section.
z Steering
components. z
REFER to Section 211 - 00 .
z Steering wheel
off- center z
Unequal front or
rear toe settings
(side-to- side). z
CHECK the wheel alignment.
ADJUST as necessary.
z Steering
components. z
REFER to Section 211 - 00 .
z Sway or roll zOverloaded,
unevenly or
incorrectly loaded
vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Loose wheel nut(s). zTIGHTEN to specification. Klj . 3 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REFER to
Section 204 - 04 .
z Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Loose front
stabilizer bar (5482)
or rear stabilizer
bar (5A772). z
TIGHTEN to specification.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Worn stabilizer
assembly bushing
(s). z
INSTALL new bushing(s) as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Front coil spring(s)
or rear spring(s). z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Vehicle leans to
one side z
Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Front coil springs or
rear springs. z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Incorrect ride
height. Lateral tilt
out of specification. z
CHECK ride height. INSTALL
new front coil springs or rear
springs as necessary. REFER
to Section 204 - 01 or
Section 204 - 02 .
z Vibration/noise zTire or wheel
runout.
z Tire flatspotting.
z Wheel bearings.
z Wheel hubs.
z Brake components.
z Suspension
components.
z Steering
components. z
REFER to Section 100 - 04 .
z Wander zUnevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Ball joint(s). zGO to the Ball Joint Inspection
component test in this section.
z Front wheel bearing
(s). z
REFER to Wheel Bearing Inspection in this section.
z Loose, worn or
damaged
suspension
components(s). z
INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Loose suspension
fasteners. z
TIGHTEN to specification.
REFER to Section 204 - 01 or
Section 204 - 02 . Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Remove the front coil spring (5310). For additional information, refer to
Spring in this section.
7. Remove the nut and the front suspension lower control arm. Discard the nut.
Installation 1. To install, reverse the removal procedure.
2. Check wheel alignment. Adjust if necessary. For additional information, refer to Section 204 - 00 . Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Repair the axle as necessary. Make sure the axle lubricant is at the correct level. Refer to
Specifications in this section.
Axle Vent
NOTE:
If a plugged vent cannot be cleared, install a new one.
A plugged vent will cause excessive seal lip wear due to internal pressure buildup. If a leak occurs,
check the vent. Make sure the vent hose is not kinked. Remove the hose from the vent nipple and
clear the hose of any foreign material. While the hose is removed, pass a length of mechanics wire in
and out of the vent to clean it. Connect the hose when done.
Flange Yoke Seal
Leaks at the axle drive pinion seal originate for the following reasons:
zSeal was not correctly installed.
z Poor quality seal journal surface.
Any damage to the seal bore (dings, dents, gouges, or other imperfections) will distort the seal casing
and allow leakage past the outer edge of the axle drive pinion seal.
The axle drive pinion seal can be torn, cut, or gouged if it is not installed carefully. The spring that
holds the axle drive pinion seal against the pinion flange may be knocked out and allow leakage past
the lip.
The rubber lips can occasionally become hard (like plastic) with cracks at the oil lip contact point. The
contact point on the pinion flange may blacken, indicating excessive heat. Marks, nicks, gouges, or
rough surface texture on the seal journal of the pinion flange will also cause leaks.
When a seal leak occurs, install a new seal and check the vent and the vent hose to make sure they
are clean and free of foreign material.
Axle Shaft Seals
Axle shaft oil seals are susceptible to the same kinds of damage as axle drive pinion seals if incorrectly
installed. The seal bore must be clean and the lip handled carefully to avoid cutting or tearing it. The
axle shaft journal surface must be free of nicks, gouges, and rough surface texture.
Differential Seals
Refer to Section 205 - 02A or
Section 205 - 02B .
Analysis of Vibration WARNING: A vehicle equipped with a Traction- Lok® differential will always have both
wheels driving. If only one wheel is raised off the floor and the rear axle is driven by the engine,
the wheel on the floor could drive the vehicle off the stand or jack. Be sure both rear wheels are
off the floor.
Few vibration conditions are caused by the rear axle. On a vibration concern, follow the diagnosis
procedure in Section 100 - 04 unless there is a good reason to suspect the axle.
Tires Klj . 3 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

crayon or chalk.
6. While holding the crayon or chalk against the tire, rotate the wheel slowly in the opposite direction until the feeling of driving the rear axle is encountered again.
7. Measure the length of the crayon or chalk mark on the tire. zIf the length of the mark is 25.4 mm (1 inch) or less, the rear axle backlash is within
allowable limits.
z If the chalk mark is greater than 25.4 mm (1 inch), check for these conditions:
„Elongation of the differential pinion shaft and holes in the differential case (4204).
„ Missing differential pinion thrust washer (4230) or differential side gear thrust
washer (4228).
„ Galling of the differential pinion shaft (4211) and bore.
„ Excessive ring gear and pinion backlash. Follow the procedure for the type of rear
axle to check backlash.
Axle Shaft Bearing Noise
Axle bearing shaft noise is similar to gear noise and differential pinion bearing whine. Axle shaft
bearing noise will usually distinguish itself from gear noise by occurring in all driving modes (drive,
coast, and float), and will persist with the transmission in NEUTRAL while the vehicle is moving at the
speed in which the concern is occurring. If the vehicle makes this noise, remove the suspect axle
shaft, install a new bearing and a new axle seal. Re- evaluate the vehicle for noise before removing any
internal components.
Bearing Rumble
Bearing rumble sounds like marbles being tumbled. This condition is usually caused by a
worn/damaged wheel bearing. The lower pitch is because the wheel bearing turns at only about one-
third of the driveshaft speed. Wheel bearing noise also may be high- pitched, similar to gear noise, but
will be evident in all four driving modes.
Symptom Chart
Symptom Chart Condition
Possible Sources Action
z Traction- Lok®
does not work in
snow, mud or on
ice z
Differential. zCARRY OUT the Traction-
Lok® Differential Operation
Check in this section. REPAIR
as necessary. REFER to
Section 205 - 02A or
Section 205 - 02B .
z Lubricant leaking
from the pinion
seal, axle shaft oil
seals z
Vent.
z Damage in the
seal contact area
or damaged or
worn seal. z
CLEAN the axle housing vent.
z INSTALL a new seal if
damage is found.
z Differential side
gears/pinion
gears are scored z
Insufficient
lubrication. z
INSTALL new gears. REFER
to Section 205 - 02A or
Section 205 - 02B . FILL the axle to
specification.
z Incorrect or
contaminated z
INSTALL new gears. REFER
to Section 205 - 02A or
Section Klj . 10 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
a
In- vehicle repair refill capacities are determined by filling the rear axle with the specified lubricant to
6.4- 14.3- mm (1/4- 9/16-in) below the bottom of the fill hole.
SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual General Specifications
Item Specification
Lubes and Sealers
SAE 80W-
90 Premium Rear Axle Lubricant XY-
80W90- QL WSP-
M2C197- A Premium Long-
Life Grease XG -1-C ESA-
M1C75- B Rust Penetrant and Inhibitor F2AZ-19A501-
A ESR-
M99C56- A High Temperature Nickel Anti-
Sieze Lubricant
F6AZ- 9L494- AA ESE-
M124A- A Clear Silicone Rubber F7AZ-
19554-CA ESB-
M4G92- A Threadlock and Sealer EOAZ-19554-
AA WSK-
M2G351- A5 Lubricant Fill Level Checks
Approximate axle fill capacity
a 1.54-1.66-
liters (3.25-3.50- pints)
6.4-14.3- mm (1/4-9/16- in) below the bottom of
the fill hole Clearance, Tolerance and Adjustments
Maximum ring gear back face runout 0.102 mm (0.004 in)
Maximum differential case runout 0.076 mm (0.003 in)
Differential side gear thrust washer thickness 0.762 mm -
0.813 mm (0.030 in - 0.032 in) Differential pinion gear thrust washer thickness 0.762 mm -
0.813 mm (0.030 in - 0.032 in) Maximum axle shaft end play 0.762 mm (0.030 in)
Ring gear backlash 0.203 mm-
0.381 mm
(0.008 in- 0.015 in)
[(0.305 mm- 0.381 mm
(0.012 in- 0.015 in) preferred] Variation between teeth maximum backlash 0.102 mm (0.004 in)
Pinion flange runout 0.25 mm (0.010 in) T.I.R.
Torque Specifications Description Nm lb-
ft lb-
in Bolt retaining the differential pinion shaft to the differential case 30 22 —
Bolt retaining the driveshaft yoke to the pinion flange 112 83 —
Bolt retaining the differential housing cover to the differential housing 44 32 —
Oil filler plug 30 22 —
Pinion bearing preload (used pinion bearings) 0.9-
1.5 — 8-
14 Pinion bearing preload (new pinion bearings) 1.8-
3.3 — 16-
29 Adapter for 205-
S127 2.2 — 20 Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: HYDRO-
BOOST ERRATIC OPERATION, STICKS,
BINDS OR GRABS z
Check accessory drive belt tension and
condition. Refer to Section 303 - 05 .
z Is the accessory drive belt OK? Yes
GO to
E3 .
No
INSTALL a new accessory drive belt.
REFER to Section 303 - 05 .
E3 CHECK POWER STEERING HOSES
z
Check power steering pressure hoses, power
steering gear pressure hoses and power
steering return hose for cracks or leaks.
z Do power steering pressure hose, power
steering gear hose and power steering
return hose check OK? Yes
GO to
E4 .
No
INSTALL new hoses as necessary.
REFER to Section 211 - 00 .
E4 CHECK BRAKE PEDAL LINKAGE
z
Check brake pedal linkage for binding or
sticking operation.
z Does pedal linkage check OK? Yes
GO to
E5 .
No
INSTALL new pedal linkage as necessary.
REFER to Section 206 - 06 .
E5 CHECK POWER STEERING PUMP SPEED
z
Check engine idle speed against
specifications.
z Is engine idle speed OK? Yes
GO to
E6 .
No
SET engine idle speed to specification.
REFER to Powertrain Control/Emissions
Diagnosis (PC/ED) manual. E6 CHECK FOR PLUGGED RETURN HOSE
z
NOTE: The return hose from the oil cooler to
the power steering reservoir has an in- line
filter in the hose.
z Disconnect power steering return hose from
power steering fluid cooler and power
steering pump reservoir.
z Pass air through hose from the oil cooler end.
z Is hose plugged? Yes
INSTALL a new power steering return
hose.
No
GO to
E7 .
E7 CHECK POWER STEERING PUMP FLOW
AND RELIEF z
Test power steering pump for correct flow
and relief pressure. Refer to Section 211 - 00 .
z Is power steering pump operating
correctly? Yes
INSTALL a new power brake hydro-
boost
unit. REFER to Section 206 - 07 .
No
INSTALL a new power steering pump.
REFER to Section 211 - 02 .
Test Step Result / Action to
Take F1 CHECK SUPPLY HOSE
z
Check for obstructions in power steering return hose and Yes Klj . 11 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

10. Inspect the front disc brake anchor plate assembly.
zCheck the guide pin boots for damage.
z Check the guide pins for binding and damage.
z Worn or damaged pins should be installed new.
Installation 1. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the
pad lining material. Do not install contaminated pads.
NOTE: Install all hardware supplied with pad kits.
Install the pads. 1. Install the new pad slippers.
2. Install the pads. Klj . 4 ba
72003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...