2003 FORD MUSTANG air suspension

REFER to
Section 204 - 04 .
z Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Loose front
stabilizer bar (5482)
or rear stabilizer
bar (5A772). z
TIGHTEN to specification.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Worn stabilizer
assembly bushing
(s). z
INSTALL new bushing(s) as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Front coil spring(s)
or rear spring(s). z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Vehicle leans to
one side z
Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Front coil springs or
rear springs. z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Incorrect ride
height. Lateral tilt
out of specification. z
CHECK ride height. INSTALL
new front coil springs or rear
springs as necessary. REFER
to Section 204 - 01 or
Section 204 - 02 .
z Vibration/noise zTire or wheel
runout.
z Tire flatspotting.
z Wheel bearings.
z Wheel hubs.
z Brake components.
z Suspension
components.
z Steering
components. z
REFER to Section 100 - 04 .
z Wander zUnevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Ball joint(s). zGO to the Ball Joint Inspection
component test in this section.
z Front wheel bearing
(s). z
REFER to Wheel Bearing Inspection in this section.
z Loose, worn or
damaged
suspension
components(s). z
INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Loose suspension
fasteners. z
TIGHTEN to specification.
REFER to Section 204 - 01 or
Section 204 - 02 . Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Wheel Studs
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the rear brake disc. For additional information, refer to Section 206 - 04 .
4. Using the special tool, remove and discard the wheel stud.
Installation CAUTION: Do not use air tools to install the wheel stud. The serrations in the hub flange
can be stripped.
1. Install the wheel stud. 1. Position a new wheel stud in the hub flange making sure the serrations on the stud line up with the serrations in the flange.
2. Position washers and a reversed wheel nut on the wheel stud.
3. Tighten the wheel nut until the wheel stud seats on the back of the hub flange.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
C-
Frame and Clamp Assembly
211- 023 (T74P-3044- A1) Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
wheel bearing life.
z brake cooling.
New wheels need to be installed when vehicle's wheels:
zare bent.
z are cracked.
z are dented.
z are heavily corroded.
z are leaking.
z have elongated wheel hub bolt holes.
z have excessive lateral or radial runout.
Wheel and tire assemblies are attached by six wheel nuts.
It is mandatory to use only the tire sizes recommended on the tire chart attached to the vehicle. Larger
or smaller tires can damage the vehicle, affect durability, and require changing the speedometer
calibration. Make sure wheel size and offsets match those recommended for the tire in use. 1. Inspect for signs of uneven wear that may indicate a need for balancing, rotation, front suspension alignment, damaged tie- rod, or steering components.
2. Check tires for: zcuts.
z stone bruises.
z abrasions
z blisters.
z embedded objects.
3. Tread wear indicators are molded into the bottom of the tread grooves. Install a new tire when the indicator bands become visible.
Symptom Chart Symptom Chart Condition
Possible Sources Action
z Tires show
excess wear on
edge of tread z
Underinflated tires. zADJUST air pressure
in tires.
z Vehicle overloaded. zRETURN vehicle.
NOTIFY customer of
overload condition.
z High- speed cornering. zRETURN vehicle.
NOTIFY customer of
cause of condition.
z Incorrect ride height. zSET ride height.
z Incorrect wheel alignment. zSET alignment to
specification. REFER Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

to
Section 204 - 00 .
z Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Tires show
excess wear in
center of tread z
Tires overinflated. zADJUST air pressure.
z Other excessive
tire wear
problems z
Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Incorrect tire pressure. zADJUST pressure.
z Loose or leaking shock
absorbers. z
TIGHTEN or INSTALL
new shock absorbers
as necessary.
z Incorrect wheel alignment. zSET alignment to
specification. REFER
to Section 204 - 00 .
z Loose, worn or damaged
suspension components. z
REFER to Section 204 - 00 .
z Wheel and tire assembly
out of balance. z
BALANCE wheel and
tire assembly.
z Excessive lateral or radial
runout of wheel. z
REFER to Section 100 - 04 .
z Wobble or
shimmy z
Damaged wheel bearings. zREFER to Section 204 - 00 .
z Loose or damaged
suspension components. z
REFER to Section 204 - 00 .
z Bent wheel. zINSTALL a new wheel
as necessary.
z Damaged tire. zINSTALL a new tire as
necessary.
z Loose wheel nuts. zTIGHTEN to
specification.
z High- speed
shake z
Wheel hub face/pilot/bolt
circle runout.
z Tires/wheels.
z Wheel bearings.
z Suspension/steering
linkage.
z Engine.
z Transmission.
z Brake discs/imbalance. z
REFER to Section 100 - 04 .
z Vehicle vibration zDriveline — engine.
z Tires. z
REFER to Section 100 - 04 . Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Driveline Angle Inspection
NOTE:
An incorrect driveline angle can cause a vibration or shudder. For additional information, refer
to Section 100 - 04 .
1. Check the vehicle for evidence or overload or sagging. Check for specified air pressures information in all four tires.
2. Normalize the suspension.
3. Drive the vehicle onto a drive- on hoist or back onto a front-end alignment rack.
4. Inspect the suspension and chassis. Verify that the vehicle curb position ride height is within specification. For additional information, refer to Section 204 - 00 .
z Measure the curb position ride height with the vehicle empty and all fluids full.
5. Place the Inclinometer flush against the bottom of the driveshaft. After the tool has been held on the driveshaft surface for 5 seconds, push the ALT ZERO button to calibrate to zero degrees.
Remove the tool.
6. To check the pinion angle, rotate the driveshaft so that the rear axle pinion flange yoke ear is parallel to the floor. Remove the U- joint snap ring, then install the special tool. Check and record
the pinion angle reading.
zIf the angle is not within specification, repair or adjust to obtain the correct angle. Inspect
the rear suspension, rear axle, rear axle mounting or the frame for wear or damage.
SECTION 205-
00: Driveline System — General Information 2003 Mustang Workshop Manual Special Tool(s)
Anglemaster II Driveline
Inclinometer
164-
R2402 or equivalent Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Axle Housing Bushing
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Remove the upper arm and bushing (5500). For additional information, refer to Section 204 - 02 .
2. Using the special tools, remove the bushing.
Installation 1. Using the special tools, install the bushing.
SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual Special Tool(s)
Axle Suspension Bushing Set
204-
S030 (T78P-5638- A) Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Axle Housing Bushing
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Remove the upper arm and bushing (5500). For additional information, refer to Section 204 - 02 .
2. Using the special tools, remove the bushing.
Installation 1. Using the special tools, install the bushing.
SECTION 205-
02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring
Gear 2003 Mustang Workshop
Manual Special Tool(s)
Axle Suspension Bushing Set
204-
S030 (T78P-5638- A) Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Axle Housing
Removal
1. CAUTION: The vehicle must be on level ground and at curb height.
Mark the rear shock absorbers relative to their protective sleeve. zDuring installation, raise the suspension to this reference mark before tightening the
suspension component fasteners.
SECTION 205-
02C: Rear Drive Axle/Differential — Ford 8.8-Inch IRS 2003 Mustang Workshop Manual Special Tool(s)
Plug Set, Differential
205-
294 (T89P-4850- B) Protector, Differential Seal
(Pair)
205-
461 Remover, Halfshaft
205-
475 Remover, Steering Arm
211-
003 (T64P-3590- F) Klj . 1 ba
142003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...