2003 FORD MUSTANG air suspension

PINPOINT TEST J: WHEEL AND TIRE I1 ROAD TEST THE VEHICLE
z
Test drive the vehicle.
z NOTE: An assistant will be needed for this road test.
z During the road test, drive the vehicle over a rough road.
Using ChassisEARs, determine from which
area/component the noise is originating.
z Is there a squeak, creak or rattle noise? Yes
GO to
I2 .
No
The suspension system is
OK. Conduct a diagnosis on
other suspect systems. I2 REAR SHOCK ABSORBER/STRUT CHECK
z
WARNING: The electrical power to the air
suspension system must be shut off prior to hoisting,
jacking or towing an air suspension vehicle. This can
be accomplished by turning off the air suspension
switch. Failure to do so can result in unexpected
inflation or deflation of the air springs, which can result
in shifting of the vehicle during these operations.
z Raise and support the vehicle.
z Check the rear shock absorber/strut mounts for loose bolts
or nuts.
z Check the rear shock absorbers/struts for damage. Carry
out a shock absorber check.
z Are the rear shock absorbers/struts loose or damaged? Yes
TIGHTEN to specifications if
loose. INSTALL new rear
shock absorbers/struts if
damaged. TEST the system
for normal operation.
No
GO to
I3 .
I3 CHECK THE REAR SPRINGS
z
Check the rear springs and rear spring mounts/brackets for
wear or damage.
z Are the rear springs or spring mounts/brackets worn or
damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
I4 .
I4 CHECK THE CONTROL ARMS/TRAILING ARMS
z
Inspect the control arm/trailing arm bushings for wear or
damage. Check for loose control arm/trailing arm bolts.
z Inspect for twisted or bent control arm/trailing arms.
z Are the control arm/trailing arms loose, damaged or
worn? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
GO to
I5 .
I5 CHECK THE STABILIZER BAR/TRACK BAR
z
Check the stabilizer bar/track bar bushings and links for
damage or wear.
z Check the stabilizer bar/track bar for damage.
z Check for loose or damaged stabilizer bar isolators or
brackets.
z Are the stabilizer bar/track bar components loose, worn
or damaged? Yes
REPAIR or INSTALL new
components as necessary.
TEST the system for normal
operation.
No
Suspension system OK.
CONDUCT diagnosis on
other suspect systems.
Test Step
Result / Action to Klj . 55 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST M: TRANSFER CASE VIBRATION the system for normal operation.
No
GO to
L6 .
L6 CHECK THE FLYWHEEL BOLTS
z
Check for loose flywheel bolts.
z Are the bolts loose? Yes
TIGHTEN the bolts to
specifications. REFER to
Section 308 - 01 . TEST the system for
normal operation.
No
GO to L7 .
L7 CHECK THE FLYWHEEL SURFACE
z
Inspect the flywheel surface for wear or damage.
Check the flywheel runout.
z Is there any damage or excessive wear? Yes
INSTALL a new flywheel. TEST
the system for normal operation.
No
Clutch system normal. CONDUCT
a diagnosis on other suspect
systems.
Test Step Result / Action to Take
M1 INSPECT THE TRANSFER CASE
z
WARNING: The electrical power to the air suspension
system must be shut off prior to hoisting, jacking or towing
an air suspension vehicle. This can be accomplished by
turning off the air suspension switch. Failure to do so can
result in unexpected inflation or deflation of the air springs,
which can result in shifting of the vehicle during these
operations.
z Inspect the transfer case for loose or missing mounting bolts.
Check for fluid seepage between the transfer case and the
transmission.
z Are the mounting bolts missing or loose? Yes
TIGHTEN to
specifications or
INSTALL new bolts as
necessary. TEST the
system for normal
operation.
No
GO to
M2 .
M2 INSPECT THE REAR DRIVESHAFT
z
NOTE: Verify that the driveshaft and pinion flange index marks
are aligned.
z Inspect the driveshaft for missing weights, damage or
undercoating.
z Inspect the U- joints for freedom of movement.
z Check driveshaft runout and, if necessary, check the pinion
flange runout.
z Is the driveshaft or U- joints worn or damaged or
misaligned? Yes
REPAIR or INSTALL a
new driveshaft as
necessary. TEST the
system for normal
operation.
No
GO to
M3 .
M3 CHECK THE DRIVELINE ANGLES
z
Measure the rear driveshaft and pinion angles. Refer to Section 205 - 00 .
z Measure the front driveshaft and pinion angles. Refer to Section 205 - 00 .
z Are the driveline angles incorrect? Yes
REPAIR as necessary.
TEST the system for
normal operation.
No Klj . 62 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Brake Disc Machining
WARNING: The electrical power to the air suspension system must be shut off prior to
hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off
the air suspension switch. Failure to do so can result in unexpected inflation or deflation of the
air springs, which can result in shifting of the vehicle during these operations.
CAUTION: Do not install brake discs that are less than the minimum thickness specified.
Do not machine a brake disc below the minimum thickness specification.
1. Check wheel bearing end- play and correct as necessary.
2. NOTE: Begin at the front of the vehicle unless the vibration has been isolated to the rear.
Remove the tire and wheel assembly.
3. Remove the brake caliper and the brake caliper anchor plate. Refer to the appropriate section in Group 206 for the procedure.
4. Inspect the brake linings. Install new brake linings if below specification. For additional information, refer to the appropriate brake section.
5. Measure and record the brake disc thickness. Install a new brake disc if the thickness after machining will be at or below specification. The specification is molded into the brake disc.
zDo not machine a new brake disc.
SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Special Tool(s)
Gauge, Clutch Housing
308-
021 (T75L-4201- A) Dial Indicator Gauge with
Holding Fixture
100-
002 (TOOL- 4201-C) or
equivalent
Material Item Specification
Metal Surface Cleaner
F4AZ-
19A536- RA or equivalent WSE-
M5B392-
A High Temperature Nickel Anti-
Seize Lubricant
F6AZ-
9L494- AA or equivalent ESE-
M12A4-A Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Powertrain/Drivetrain Mount Neutralizing
WARNING: The electrical power to the air suspension system must be shut off prior to
hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off
the air suspension switch. Failure to do so can result in unexpected inflation or deflation of the
air springs, which can result in shifting of the vehicle during these operations.
1. Raise and support the vehicle.
2. Loosen, but do not remove, the powertrain/drivetrain mount fasteners.
3. Lower the vehicle.
4. CAUTION: Do not twist or strain the powertrain/drivetrain mounts.
Move the vehicle in forward and reverse 0.6- 1.2 meters (2-4 ft).
5. Raise and support the vehicle.
6. Tighten the powertrain/drivetrain mount fasteners.
7. Lower the vehicle.
8. Test the system for normal operation.
SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Exhaust System Neutralizing
WARNING: Exhaust gases contain carbon monoxide, which is harmful to health and
potentially lethal. Repair exhaust system leaks immediately. Never operate the engine in an
enclosed area.
WARNING: Exhaust system components are hot.
NOTE: Neutralize the exhaust system to relieve strain on mounts which can be sufficiently bound up to
transmit vibration as if grounded.
1. WARNING: The electrical power to the air suspension system must be shut off prior
to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by
turning off the air suspension switch. Failure to do so can result in unexpected inflation
or deflation of the air springs, which can result in shifting of the vehicle during these
operations.
CAUTION: Make sure the system is warmed up to normal operating temperature, as
thermal expansion can be the cause of a strain problem.
Raise and support the vehicle.
2. Loosen all exhaust hanger attachments and reposition the hangers until they hang free and straight.
3. Loosen all exhaust flange joints.
4. Place a stand to support the muffler parallel to the vehicle frame with the muffler pipe bracket free of stress.
5. Tighten the muffler connection.
6. Tighten all the exhaust hanger clamps and flanges (tighten the exhaust manifold flange joint last).
zVerify there is adequate clearance to prevent grounding at any point in the system. Make
sure that the catalytic converter and heat shield do not contact the frame rails.
z After neutralization, the rubber in the exhaust hangers should show some flexibility when
movement is applied to the exhaust system.
z With the exhaust system installed securely and cooled, the rear hanger should be angled
forward.
7. Lower the vehicle.
8. Test the exhaust system for normal operation.
SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Wheel Bearing Check
1. WARNING: The electrical power to the air suspension system must be shut off prior
to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by
turning off the air suspension switch. Failure to do so can result in unexpected inflation
or deflation of the air springs, which can result in shifting of the vehicle during these
operations.
Raise the vehicle until the front tires are off the floor.
zMake sure the wheels are in a straight forward position.
2. NOTE: Make sure the wheel rotates freely and that the brake pads are retraced sufficiently to
allow free movement of the tire and wheel assembly.
Spin the tire by hand to check the wheel bearings for roughness.
3. Grip each front tire at the top and bottom and move the wheel inward and outward while lifting the weight of the tire off the front wheel bearing.
4. If the tire and wheel (hub) is loose on the spindle, does not rotate freely, or has a rough feeling when spun, carry out one of the following:
1. On vehicles with inner and outer bearings, inspect the bearings and cups for wear or damage. Adjust or install new bearings and cups as necessary.
2. On vehicles with one sealed bearing, install a new wheel hub.
SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Suspension System
Inspection and Verification
1. Road test. zVerify the customer's concern by performing a road test on a smooth road.
2. Inspect tires. zCheck the tire pressure with all normal loads in the vehicle and the tires cold. For
additional information, refer to the vehicle certification (VC) label.
z Verify that all tires are sized to specification.
z Inspect the tires for incorrect wear and damage.
3. Inspect chassis and underbody. zRemove any excessive accumulation of mud, dirt or road deposits from the chassis and
underbody.
4. Inspect for aftermarket equipment. zCheck for aftermarket changes to the steering, suspension, wheel and tire components
(such as competition, heavy duty, etc.) The specifications shown in this manual do not
apply to vehicles equipped with aftermarket equipment.
5. Inspect shock absorbers. All vehicles are equipped with gas- pressurized hydraulic shock absorbers. These shock
absorbers are not adjustable or refillable and cannot be repaired.
zOil Leak: A light film of oil (weepage) on the upper portion of the shock absorber is
permissible and is a result or correct shock lubrication. Weepage is a condition in which a
film of oil accumulates on the thin tube (body) and is normally noticed due to the
collection of dust in this area. If shock absorbers exhibit this weepage condition, they are
functional units and new shock absorbers should not be installed. Leakage is a condition
in which the entire shock absorber body is covered with oil and the oil will drip from the
shock absorber onto the pavement. If condition exists:
„Make sure fluid observed is not from sources other than the shock absorber.
„ Install a new shock absorber, if necessary.
z Vehicle Sag: Many times new shock absorbers are installed in an effort to solve a vehicle
sag concern. Shock absorbers by design are hydraulic damping units only and, unlike
suspension springs, do not support any suspension loads. Therefore, installing a new
shock absorber will not correct a vehicle sag concern.
z Installment in Pairs: In the past it was recommended that new shock absorbers be
installed in pairs if one unit became unrepairable. New shock absorbers no longer need
to be installed in pairs when only one unit is not repairable.
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Visual Inspection Chart
Mechanical Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. If an obvious cause for an observed or reported condition is found, correct the cause (if
possible) before proceeding to the next step.
7. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .
Symptom Chart z
Front wheel bearing(s)
z Loose or damaged front or rear suspension components
z Loose, damaged or missing suspension fastener(s)
z Damaged spring(s)
z Damaged or leaking strut and spring assemblies
z Damaged or leaking shock absorber(s)
z Worn or damaged suspension bushing(s)
z Loose, worn or damaged steering system components
z Damaged axle components
Symptom Chart Condition
Possible Sources Action
z Dogtracking zExcessive rear
thrust angle. z
CHECK the wheel alignment.
ADJUST as necessary.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Drive axle
damaged. z
REPAIR as necessary. Refer
to the appropriate section in
Group 205 for the procedure..
z Drift/pull zUnequal tire
pressure. z
ADJUST tire pressure.
z Excessive side-to-
side difference in
caster or camber. z
CHECK the wheel alignment.
ADJUST as necessary.
z Tire forces. zROTATE tires front to rear.
z Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Steering
components. z
REFER to Section 211 - 00 .
z Brake drag. zREFER to Section 206 - 00 .
z Front bottoming
or riding low z
Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Front coil springs
(5310). z
CHECK ride height. INSTALL
new springs as necessary.
REFER to Section 204 - 01 .
z Incorrect tire
wear z
Incorrect tire
pressure (rapid
center rib or inner
and outer edge
wear). z
ADJUST tire pressure. Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...