2003 FORD MUSTANG clip

REMOVAL AND INSTALLATION
Caliper
Removal
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Disengage the parking brake cable end from the parking brake lever arm.
4. Remove the parking brake cable retaining clip.
5. Remove the parking brake cable and conduit.
SECTION 206-
04: Rear Disc Brake 2003 Mustang Workshop Manual Special Tool(s)
Rear Caliper Piston Adjuster
206-
026 (T87P-2588- A) Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Remove the rear disc brake piston and adjuster from the caliper bore.
6. Remove and discard the piston dust boot seal and piston seal from the caliper bore.
7.
CAUTION: The parking brake lever pin retainer clip (2A746) and spring cover are
spring- loaded. Use care when removing the parking brake lever pin retainer clip.
Remove the parking brake lever pin retainer clip. zUnload the spring tension from the parking brake lever pin retainer clip and spring cover
using Screw and Cross Block, a 6- mm washer head nut and a 1/2-inch drive 14-mm
socket.
z Remove the parking brake lever pin retainer clip with suitable snap- ring pliers.
z Remove Screw and Cross Block. Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 206-
05: Parking Brake and Actuation 2003 Mustang Workshop Manual Torque Specifications
Description Nm Lb/Ft
Parking brake control-
to-cowl nut 17 13
Brake hose clip mounting bolt 12 9 Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST B: PARKING BRAKE WILL NOT RELEASE to Section 100 - 02 .
z Inspect for broken or binding parking
brake cables or broken guide clips.
z Is there a parking brake cable
concern? INSTALL a new parking brake cable as
necessary. TEST the system for normal
operation.
No
GO to
A2 .
A2 CHECK THE PARKING BRAKE
CONTROL z
Operate the parking brake control.
z Does the parking brake control
operate smoothly? Yes
INSTALL a new parking brake lever. RESTORE
vehicle and TEST the system for normal
operation.
No
REPAIR the binding condition in the parking brake
control. TEST the system for normal operation.
Test Step Result / Action to Take
B1 CHECK PARKING BRAKE CONTROL
z
Raise and support the vehicle. Refer to
Section 100 - 02 .
z Release parking brake by pulling
upward on hand lever and pushing
release button.
z Did parking brake release? Yes
GO to
B2 .
No
INSTALL a new parking brake control.
RESTORE the vehicle and TEST the system for
normal operation. B2 CHECK PARKING BRAKE CABLES
z
Loosen tensioner. Refer to Parking Brake Cable Tension Release in this
section.
z Move the gearshift lever to NEUTRAL
position.
z Rotate rear wheels by hand.
z Did rear wheels turn freely? Yes
GO to
B3 .
No
INSTALL new parking brake cables. RESTORE
the vehicle and TEST the system for normal
operation. B3 CHECK REAR PARKING BRAKE
LEVERS z
Disconnect parking brake levers one at
a time.
z Rotate wheel affected by disconnected
parking brake lever.
z Did wheel turn freely? Yes
INSTALL a new parking brake lever. RESTORE
vehicle and TEST the system for normal
operation.
No
REPAIR or INSTALL a new rear brake
component if worn or damaged. TEST the
system for normal operation. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Remove the parking brake rear cable and conduit from the routing clip bolts.
5. Disconnect the parking brake rear cable and conduit from the parking brake lever (2A637).
6. Remove the clip from the rear disc brake caliper (2552). Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Sensor —
Front
Removal 1. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
2. Remove the inner fender splash shield. 1. Remove the inner fender splash shield push pins.
2. Remove the inner fender splash shield screw.
3. Remove the inner fender splash shield.
3. Remove the front anti- lock brake sensor electrical connector.
4. Remove the front anti- lock brake sensor harness from the anti- lock brake sensor harness clips.
5. Remove the front anti- lock brake sensor.
1. Remove the front anti- lock brake sensor bolt.
2. Remove the anti- lock brake sensor harness from the harness clips.
3. Remove the front anti- lock brake sensor.
SECTION 206-
09A: Anti-Lock Control — Rear 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Sensor —
Front
Removal 1. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
2. Remove the inner fender splash shield. 1. Remove the inner fender splash shield push pins.
2. Remove the inner fender splash shield screw.
3. Remove the inner fender splash shield.
3. Remove the front anti- lock brake sensor electrical connector.
4. Remove the front anti- lock brake sensor harness from the anti- lock brake sensor harness clips.
5. Remove the front anti- lock brake sensor.
1. Remove the front anti- lock brake sensor bolt.
2. Remove the anti- lock brake sensor harness from the harness clips.
3. Remove the front anti- lock brake sensor.
SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
All fasteners are important because they can affect the performance of vital parts and systems.
Incorrect installation of the fasteners can result in major repair expenses. They must be installed new
with fasteners of the same part number if installation becomes necessary. Do not install a new part of
lesser quality or substitute a design. Torque values must be used as specified during assembly to
make sure these parts function correctly.
The body of the steering column (3C529) is made of magnesium die castings. The steering column is
attached to a support that is an integral part of the instrument panel. The lower attachments of the
steering column are through a bracket that bends during collapse. The upper attachments are through
plastic shear modules that separate from the main casting during collapse. A clip and washer are
attached to the shear modules to reduce steering column shake and to assist in installation of the
steering column. 45 N621906 Nut
46 N803942 Bolt
47 3A525 Intermediate shaft coupling
48 11A128 Ignition key warning switch terminal
49 N806583 Bearing housing retaining screw
50 N804865-
S58 Screw
51 14A06 Wire connector bracket
52 3E715 Lock lever lower actuator
53 3E691 Lock pawl
54 3F723 Actuator housing
55 3E745 Lock actuator cover
56 3F719 Ignition/shifter interlock cable
57 N808124-
58M Screw
58 3D655 Position spring
59 3D656 Tilt flange bumper
60 N806582 Tilt pivot screws
61 11582 Ignition switch lock cylinder
62 3E700 Lock housing bearing
63 3E717 Lock gear
64 3530 Upper shroud
65 3511 Lock cylinder housing
66 N805857 Lock actuator lever pin
67 3D681 Bearing retainer Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...