2003 FORD MUSTANG air conditioning

SPECIFICATIONS
SECTION 412-
03: Air Conditioning 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricant
PAG Refrigerant Compressor Oil (R-134a Systems) F7AZ-19589-
DA (MC YN-12-
C) WSH-
M1C231-
B
Torque Specifications Description Nm lb-
ft lb-
in A/C compressor mounting bolts 25 18 —
A/C manifold retaining bolt 20 15 —
3.8L engine A/C compressor mounting bracket bolts 47 35 —
3.8L engine A/C compressor mounting bracket nut 25 18 —
A/C compressor clutch retaining bolt 13 10 —
Suction accumulator/drier clamp screw 8 — 71
Coolant bottle bolts 10 — 89
Peanut fittings 8 — 71
Radiator bracket bolts 9 — 81
Condenser core bracket bolts 5 — 44
A/C muffler bracket nut 25 18 — Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Air Conditioning
The A/C refrigerant system is a clutch cycling orifice tube type. The system components are:
zA/C compressor (19703)
z A/C clutch (2884)
z A/C condenser core (19712)
z A/C evaporator core (19860)
z suction accumulator (19C836)
z connecting refrigerant lines
The refrigeration system operation is controlled by the:
zA/C evaporator core orifice (19D990).
z A/C cycling switch (19E561).
z A/C compressor pressure relief valve (19D644).
z Refrigerant containment switch (3.8L) (19D594).
z Dual- function pressure switch (4.6L) (19D594).
The refrigerant system incorporates an A/C compressor controlled by an A/C cycling switch.
The A/C cycling switch senses A/C evaporator core pressure to control A/C compressor operation.
An A/C compressor pressure relief valve is installed in the A/C manifold and tube (19D734) to protect
the refrigerant system against excessively high refrigerant pressures.
An evaporator core orifice is installed in the A/C evaporator core inlet tube to meter the liquid
refrigerant into the A/C evaporator core.
A refrigerant containment switch is installed on 3.8L vehicles to cut- off A/C compressor operation in
the event of abnormally high refrigerant system pressure.
A dual- function pressure switch is used on 4.6L vehicles for cooling fan control, and to cut- off A/C
compressor operation in the event of abnormally high refrigerant system pressure. Refrigeration System Components SECTION 412-
03: Air Conditioning 2003 Mustang Workshop Manual Klj . 1 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

A/C Evaporator Core
NOTE:
The evaporator core is not separately serviceable, it is serviced only with the evaporator core
housing assembly.
NOTE: Installation of a new suction accumulator is not required when repairing the air conditioning
system except when there is physical evidence of contamination from a failed A/C compressor or
damage to the suction accumulator.
The A/C evaporator core is the plate/fin type with a unique refrigerant flow path.
zA mixture of refrigerant and oil enters the bottom of the A/C evaporator core through the A/C
evaporator core inlet tube and moves out of the A/C evaporator core through the A/C
evaporator core outlet tube.
z This flow pattern accelerates the flow of refrigerant and oil through the A/C evaporator core.
Evaporator Core Orifice
NOTE: The evaporator core orifice is an integral part of the condenser to evaporator line and should
be installed as an assembly with the line.
NOTE: A new evaporator core orifice should be installed whenever a new A/C compressor is installed.
The evaporator core orifice has the following characteristics:
zIt is located in the A/C condenser to evaporator line.
z It has filter screens located on the inlet and outlet ends of the tube body.
z The inlet filter screen acts as a strainer for the liquid refrigerant flowing through the evaporator
core orifice.
z O-ring seals on the evaporator core orifice prevent the high- pressure liquid refrigerant from
bypassing the evaporator core orifice. Klj . 5 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Adjustment or repair cannot be made to the evaporator core orifice assembly. A new evaporator
core orifice must be installed as a unit.
Suction Accumulator
NOTE: Installation of a new suction accumulator is not required when repairing the air conditioning
system except when there is physical evidence of contamination from a failed A/C compressor or
damage to the suction accumulator.
In addition to the preceding condition, a new suction accumulator should be installed if one of the
following conditions exist:
zThe suction accumulator is perforated.
z The refrigerant system has been opened to the atmosphere for a period of time longer than
required to make a minor repair.
z There is evidence of moisture in the system such as internal corrosion of metal refrigerant lines
or the refrigerant oil is thick and dark. Item Part Number Description
1 19E561 A/C cycling switch
2 — O-
ring seal (part of 19C836) 3 19D701 Low pressure service gauge port valve
4 — Inlet from A/C evaporator core (part of 19C836)
5 — Outlet to A/C compressor (part of 19C836)
6 — Anti-
siphon hole (part of 19C836) 7 — Desiccant bag (part of 19C836)
8 — Oil return orifice filter (part of 19C836)
9 — Vapor return tube (part of 19C836)
10 — Suction accumulator dome (part of 19C836) Klj . 6 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Air Conditioning
Refer to
Section 412 - 00 .
SECTION 412-
03: Air Conditioning 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Air Conditioning (A/C) Compressor —
3.8L
Removal and Installation CAUTION: If installing a new air conditioning compressor due to an internal failure of the
old unit, you must carry out the following procedures to remove contamination from the air
conditioning system.
zIf A/C flushing equipment is available, carry out the flushing of the air conditioning
system prior to installing a new air conditioning compressor. For additional information,
refer to Section 412 - 00 .
z If A/C flushing equipment is not available, carry out filtering of the air conditioning
system after a new air conditioning compressor has been installed. For additional
information, refer to Section 412 - 00 .
z Install a new evaporator core orifice (19D990), as directed by the A/C flushing or filtering
procedure.
z Install a new suction accumulator (19C836), as directed by the A/C flushing or filtering
procedure.
NOTE: Installation of a new suction accumulator is not required when repairing the air conditioning
system except when there is physical evidence of system contamination from a failed A/C compressor
or damage to the suction accumulator.
1. If flushing of the air conditioning system has not been performed, recover the refrigerant. For additional information, refer to Section 412 - 00 .
2. Disconnect the battery. For additional information, refer to Section 414 - 01
3. Unlatch the air breather.
SECTION 412-
03: Air Conditioning 2003 Mustang Workshop Manual Material
Item Specification
PAG Refrigerant Compressor
Oil (R-
134a Systems)
F7AZ- 19589- DA (Motorcraft YN-
12- C) WSH-
M1C231-
B Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

9. Remove the bolts and the A/C compressor.
10. To install, reverse the removal procedure. zInstall new O- ring seals lubricated in clean PAG oil.
z If filtering of the refrigerant system is not to be performed, lubricate the refrigerant system
with the correct amount of clean PAG oil. For additional information, refer to Section 412 -
00 .
11. If filtering of the air conditioning system is not to be performed, evacuate, leak test and charge the refrigerant system. For additional information, refer to Section 412 - 00 . Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Air Conditioning (A/C) Compressor —
4.6L
Removal and Installation CAUTION: If installing a new air conditioning compressor due to an internal failure of the
old unit, you must carry out the following procedures to remove contamination from the air
conditioning system.
zIf A/C flushing equipment is available, carry out the flushing of the air conditioning
system prior to installing a new air conditioning compressor. For additional information,
refer to Section 412 - 00 .
z If A/C flushing equipment is not available, carry out filtering of the air conditioning
system after a new air conditioning compressor has been installed. For additional
information, refer to Section 412 - 00 .
z Install a new evaporator core orifice (19D990), as directed by the A/C flushing or filtering
procedure.
z Install a new suction accumulator (19C836), as directed by the A/C flushing or filtering
procedure.
NOTE: Installation of a new suction accumulator is not required when repairing the air conditioning
system except when there is physical evidence of system contamination from a failed A/C compressor
or damage to the suction accumulator.
1. If flushing of the air conditioning system has not been performed, recover the refrigerant. For additional information, refer to Section 412 - 00 .
2. Remove the drive belt from the A/C compressor pulley.
3. Raise the vehicle. For additional information, refer to Section 100 - 02 .
4. Disconnect the A/C compressor electrical connector. SECTION 412-
03: Air Conditioning 2003 Mustang Workshop Manual Material
Item Specification
PAG Refrigerant Compressor
Oil (R-
134a Systems)
F7AZ- 19589- DA (Motorcraft YN-
12- C) WSH-
M1C231-
B Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...