2003 FORD MUSTANG wheel

11 N620482 Dowel
12 87836 Plug
Item Part Number Description
1 N807198 Dowel pin (2 req'd)
2 N807309 Bolt
3 N807959 Bolt
4 18663 Heater water hose
5 W500110 Bolt (2 req'd)
6 12A699 Knock sensor (2 req'd)
7 N807309 Bolt (2 req'd)
8 18696 Heater water hose
9 7120 Pilot bearing
10 6K318 Crankshaft rear retainer
11 N806155 Bolt (6 req'd)
12 6310 Crankshaft oil slinger
13 6375 Flexplate
14 N806168 Bolt (6 req'd)
15 — Flywheel
16 N808139 Bolt (8 req'd)
17 7550 Clutch disc
18 7563 Clutch pressure plate
19 N808969 Bolt (6 req'd)
20 6701 Crankshaft rear oil seal
21 N806007 Dowel pin (2 req'd) Klj . 13 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Timing Drive Components
Removal CAUTION: Since the engine is not free- wheeling, if the crankshaft or the camshafts are
moved in any manner during removal and installation, the crankshaft and the camshafts must
be re- synchronized.
1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this
section.
2. Remove the crankshaft sensor ring from the crankshaft.
3. CAUTION: Unless otherwise instructed, at no time when the timing chains are
removed and the cylinder heads are installed is the crankshaft or the camshaft to be
rotated. Severe piston and valve damage will occur.
Using the special tool, position the crankshaft as shown.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Special Tool(s)
Holding Tool, Crankshaft
303-
448 (T93P-6303- A) Klj . 1 ba
72003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Exhaust Manifold LH
Removal and Installation 1. Position the steering wheel straight ahead and lock the column.
2. Disconnect the battery ground cable. For additional information, refer to Section 414 - 01 .
3. Raise the vehicle. For additional information, refer to Section 100 - 02 .
4. Remove the dual converter Y- pipe. For additional information, refer to Section 309 - 00 .
5. Remove and discard the pinch bolt.
6. Separate the steering coupler.
7. Disconnect the exhaust gas recirculation (EGR) tube at the exhaust manifold.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Flywheel
Removal 1. Remove the clutch components. For additional information, refer to Section 308 - 01 .
2. Remove the bolts and the flywheel.
Installation 1. To install, reverse the removal procedure.
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Automatic transmission vehicles
1. Remove the flexplate. For additional information, refer to Flexplate in this section.
Manual transmission vehicles 2. Remove the flywheel. For additional information, refer to Flywheel in this section.
All vehicles 3. Using the special tools, remove the crankshaft oil slinger.
4. Using the special tools, remove the crankshaft rear oil seal.
Installation
All vehicles 1. Using the special tools, install the crankshaft rear oil seal. zLubricate the oil seal using clean engine oil. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Using the special tool, install the crankshaft oil slinger.
Manual transmission vehicles 3. Install the flywheel. For additional information, refer to Flywheel in this section.
Automatic transmission vehicles 4. Install the flexplate. For additional information, refer to Flexplate in this section. Klj . 3 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

43. Remove the three bolts and the starter.
Automatic transmission vehicles 44. Remove the flywheel inspection cover.
45. Remove the torque converter nuts. All vehicles Klj . 11 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Disassembly
Manual transmission vehicles
1. Remove the clutch and pressure plate. For additional information, refer to Section 308 - 02 .
2. Remove the flywheel.
Automatic transmission vehicles 3. Remove the flexplate. For additional information, refer to Flexplate in this section.
All vehicles 4. Using the special tool, remove the rear oil slinger. 303-
567 (T97P-6565- AH) Remover, Crankshaft Front Oil
Seal
303-
107 (T74P-6700- A) Klj . 2 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...