2003 FORD MUSTANG wheel

DESCRIPTION AND OPERATION
Engine Ignition
Eight separate ignition coils:
zare controlled by the powertrain control module (PCM).
z are mounted directly above each spark plug.
z are controlled by the powertrain control module for correct firing sequence.
The spark plug:
zchanges the high voltage pulse into a spark which ignites the fuel and air mixture.
z originally equipped on the vehicle has a platinum- enhanced active electrode for long life.
The crankshaft position (CKP) sensor:
NOTE: Initial engine ignition timing is set at 10 degrees ± 2 degrees before top dead center (BTDC)
and is not adjustable. For additional information, refer to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
zis a variable reluctance sensor, triggered by a 36- minus-1 tooth trigger pulse wheel located on
the crankshaft, inside the engine front cover.
The sine wave type signal generated from the crankshaft position sensor provides two types of
information:
zposition of the crankshaft in 10 degree increments
z the crankshaft speed (rpm)
For additional information, refer to Section 303 - 14 .
SECTION 303-
07C: Engine Ignition — 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Evaporative Emission Canister
Removal and Installation
1. WARNING: The evaporative emission system contains fuel vapor and condensed
fuel vapor. Although not in large quantities, it still presents the danger of explosion or
fire. Disconnect the battery ground cable from the battery to minimize the possibility of
an electrical spark occurring, possibly causing a fire or explosion if fuel vapor or liquid
fuel is present in the area. Failure to follow these instructions may result in personal
injury.
Disconnect the battery ground cable. For additional information, refer to Section 414 - 01 .
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Remove the left rear wheel. For additional information, refer to Section 204 - 04 .
4. WARNING: Do not smoke or carry lighted tobacco or open flame of any type when
working on or around any fuel- related component. Highly flammable mixtures are always
present and may be ignited. Failure to follow these instructions may result in personal
injury.
Disconnect the canister vent solenoid hose assembly.
5. Disconnect the connector.
6. Disconnect the evaporative emission (EVAP) canister purge outlet tube.
SECTION 303-
13: Evaporative Emissions 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Evaporative Emission Canister Purge Valve
Removal and Installation
1. WARNING: The evaporative emission system contains fuel vapor and condensed
fuel vapor. Although not in large quantities, it still presents the danger of explosion or
fire. Disconnect the battery ground cable from the battery to minimize the possibility of
an electrical spark occurring, possibly causing a fire or explosion if fuel vapor or fuel
liquid is present in the area. Failure to follow these instructions may result in personal
injury.
Disconnect the battery ground cable. For additional information, refer to Section 414 - 01 .
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Remove the RH front wheel. For additional information, refer to Section 204 - 04 .
4. Remove the right front splash shield. 1. Remove the three screws.
2. Remove the five pin- type retainers.
5. Disconnect the connector.
6. Disconnect the main emission vacuum control connector.
SECTION 303-
13: Evaporative Emissions 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Evaporative Emission Test Port
Removal and Installation
1. Disconnect the pin- type retainer.
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Remove the RH front wheel. For additional information, refer to Section 204 - 04 .
4. Remove the RH front splash shield. 1. Remove the three screws.
2. Remove the five pin- type retainers.
5. Remove the evaporative emission test port by disconnecting at the EVAP canister purge outlet tube junction.
6. To install, reverse the removal procedure.
SECTION 303-
13: Evaporative Emissions 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Electronic Engine Controls
The electronic engine controls consist of the following:
zpowertrain control module (PCM)
z throttle position (TP) sensor
z idle air control (IAC) valve
z engine coolant temperature (ECT) sensor
z cylinder head temperature sensor
z camshaft position (CMP) sensor
z crankshaft position (CKP) sensor
z mass air flow (MAF) sensor
z intake air temperature (IAT) sensor
z heated oxygen sensor (HO2S) — front
z catalyst monitor sensor — rear
z wheel speed sensor
The powertrain control module needs the following inputs to calibrate the engine correctly:
zcrankshaft position
z engine rpm
z engine load (manifold pressure)
z atmospheric (barometric) pressure
z engine coolant temperature
The throttle position sensor:
zsends the powertrain control module a signal indicating the throttle plate angle.
z is the main input to the powertrain control module from the driver.
The idle air control valve:
zcontrols bypass air around the throttle plate at low speeds.
z is controlled by the powertrain control module.
The cylinder head temperature sensor:
zprovides a gauge signal for coolant temperature.
z is mounted on rear of LH cylinder head.
z sends the powertrain control module a signal indicating engine temperature.
z resistance decreases as coolant temperature increases.
SECTION 303-
14: Electronic Engine Controls 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

The camshaft position sensor:
zsends the powertrain control module a signal indicating camshaft position, used for fuel
synchronization.
The crankshaft position sensor:
zsends the powertrain control module a signal indicating crankshaft position.
z is essential for calculating spark timing.
The mass air flow sensor:
zsends the powertrain control module a signal indicating mass air flow rate of air entering the
engine.
The intake air temperature sensor:
zsends the powertrain control module a signal indicating the temperature of the air entering the
engine.
The heated oxygen sensor:
zhas the ability to create a voltage signal depending on exhaust oxygen content.
z provides feedback information to the powertrain control module used to calculate fuel delivery.
The rear catalyst monitor sensor:
zmonitors oxygen content after the oxygen flows through the catalytic converter.
z provides a voltage to the powertrain control module used to calculate catalytic converter
integrity.
The wheel speed sensor:
zsends a signal to the powertrain control module indicating wheel speed. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Transmission Description
The 4R70W has the following features:
zWide ratio gears
z Four speeds
z Rear wheel drive
z Automatic
z Electronic shift
z Torque converter clutch control
z Line pressure controls
The transmission uses Ravigneaux- style double-pinion gearset with two bands, one one- way roller
clutch, one mechanical diode and four friction clutches to produce four forward gears and Reverse.
4R70W Automatic Transmission SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

The reverse clutch couples the input shaft to the reverse sun gear, applied in reverse range only.
One-
Way Clutch— Planetary (Low)
The planetary (low) one- way clutch is a roller clutch that holds the planetary gearset in first gear, (D)
and D ranges. During automatic coasting downshifts into first gear ((D) and D ranges), the planetary
one- way clutch freewheels so there is no engine braking.
One- Way Clutch— Intermediate 2 7B442 Reverse clutch plate external splined (steel)
3 7B066 Reverse clutch pressure plate (rear)
4 7D483 Reverse clutch pressure plate retaining ring
(select fit)
5 7F207 Forward clutch cylinder and input shaft assembly
6 7A019 Reverse clutch sun gear assembly
7 7B164 Reverse clutch plate internal splined (friction)
Item Part
Number Description
1 7A130 Planetary gear support assembly
2 7A089 Planetary one-
way clutch cage and spring roller
assembly 3 7A398 Planetary assembly
Item Part Number Description
1 391267-
S Retaining ring
2 7A089 Intermediate one-
way clutch assembly 3 7D044 Reverse clutch drum assembly Klj . 4 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...