2003 FORD MUSTANG tow

4. Install a differential bearing shim on the left side.
5.
CAUTION: Always install the bearing caps in their identical locations and positions.
NOTE: Apply pressure toward the left side to make sure the left differential bearing cup seats
correctly.
Install the left bearing cap and loosely install the bolts.
6. Install progressively larger differential bearing shims on the right side until the largest shim selected is installed by hand. Klj . 7 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

23.
NOTE: Apply pressure toward the left side to fully seat the differential bearing cup.
Install progressively larger differential bearing shims on the RH side until the largest differential
bearing shim selected can be assembled with a slight drag feel.
24. Install the RH differential bearing cap. zTighten both bearing caps to specification.
25. Rotate the differential assembly to make sure it turns freely. Klj . 10 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST G: HYDRO-
BOOST BRAKE SYSTEM OPERATION
SUSPECT connections between the power steering pump reservoir and
between the power steering pump reservoir and the hydro-
boost
power brake booster.
z Are there any obstructions? REMOVE
obstructions or
INSTALL a new
hose.
No
GO to
F2 .
F2 CHECK BOOSTER OPERATION
z
Have an assistant check the fluid in the power steering pump
reservoir while rapidly applying the brake pedal approximately one
inch.
z Does the fluid show any movement or spouting? Yes
System OK.
No
INSTALL a new
hydro-boost
assembly. Test Step Result / Action to Take
G1 CHECK BASIC OPERATION
z
Key in OFF position.
z Press and release brake pedal several times to deplete all
hydraulic pressure from the hydro- boost power brake
booster.
z Press and hold brake pedal with light pressure.
z Key in START position.
z Does the brake pedal fall slightly and hold, and is less
pressure now required to hold brake pedal at the new
position? Yes
Hydro-
boost is OK.
No
GO to G2 .
G2 CHECK FOR HYDRAULIC BRAKE LEAK
z
With engine running, press and release brake pedal several
times.
z Hold brake pedal down with medium pressure, 34- 47 Nm
(25- 35 lb- ft).
z Does brake pedal move toward floor? Yes
GO to
G3 .
No
GO to G4 .
G3 CHECK FOR LEAKS —
BRAKE FLUID LINES z
Check for leaks at brake lines, including brake master
cylinder and brake hose.
z Do components check OK? Yes
COMPLETE master cylinder
By-
Pass Condition Test in
this section.
No
INSTALL new hoses and
lines as necessary. G4 CHECK HYDRO-
BOOST CONNECTIONS z
Clean the hydro- boost power brake booster, power steering
pressure hose, power steering gear pressure hose and
power steering return hose and connection.
z Start engine and run at idle.
z Check hose connections for leakage.
z Do hose connections check OK? Yes
GO to
G5 .
No
REPAIR or INSTALL new
hose and connections as
necessary. G5 CHECK FOR HYDRO-
BOOST LEAK Klj . 12 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

11. Remove the snap ring.
12. Remove the upper bearing spring (3520).
13. Remove the bearing sleeve (3518).
14. Remove the lower bearing tolerance ring (3L539).
1. Slide the steering column shaft in toward the lock cylinder housing (3511).
2. Slide the steering column bearing tolerance ring from the steering column shaft and remove the shaft. Klj . 4 ba
182003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. If compression improves considerably, piston rings are faulty.
2. If compression does not improve, valves are sticking or seating incorrectly.
3. If two adjacent cylinders indicate low compression pressures and squirting oil on each piston
does not increase compression, the head gasket may be leaking between cylinders. Engine oil
or coolant in cylinders could result from this condition.
Use the Compression Pressure Limit Chart when checking cylinder compression so that the
lowest reading is within 75 percent of the highest reading.
Cylinder Leakage Detection
When a cylinder produces a low reading, use of the Engine Cylinder Leak Detection/Air Pressurization
Kit will be helpful in pinpointing the exact cause.
The leakage detector is inserted in the spark plug hole, the piston is brought up to dead center on the
compression stroke, and compressed air is admitted.
Once the combustion chamber is pressurized, a special gauge included in the kit will read the
percentage of leakage. Leakage exceeding 20 percent is excessive.
While the air pressure is retained in the cylinder, listen for the hiss of escaping air. A leak at the intake
valve (6507) will be heard in the throttle body (9E926). A leak at the exhaust valve (6505) can be
heard at the tail pipe. Leakage past the piston rings will be audible at the positive crankcase ventilation
(PCV) connection. If air is passing through a blown head gasket to an adjacent cylinder, the noise will
be evident at the spark plug hole of the cylinder into which the air is leaking. Cracks in the cylinder
block or gasket leakage into the cooling system may be detected by a stream of bubbles in the radiator
(8005).
Oil Consumption Test
The following diagnostic procedure is used to determine the source of excessive internal oil
consumption. 1. NOTE: Oil use is normally greater during the first 16,100 km (10,000 miles) of service. As
mileage increases, oil use generally decreases. Vehicles in normal service should get at least
1,450 km per liter (900 miles per quart) after 16,000 km (10,000 miles) of service. High speed
driving, towing, high ambient temperature and other factors may result in greater oil use.
Define excessive oil consumption, such as the number of miles driven per liter (quart) of oil
used. Also determine customer's driving habits, such as sustained high speed operation,
towing, extended idle and other considerations.
2. Verify that the engine has no external oil leak as described under Engine Oil Leaks in the Diagnosis and Testing portion of this section.
3. Verify that the engine has the correct oil level dipstick (6750).
4. Verify that the engine is not being run in an overfilled condition. Check the oil level at least five minutes after a hot shutdown with the vehicle parked on a level surface. In no case should the
level be above MAX or the letter F in FULL. If significantly overfilled, carry out Steps 6a through
6d.
5. Verify the spark plugs are not oil saturated. If the spark plugs are oil saturated and compression is good it can be assumed the valve seals or valve guides are at fault. Klj . 9 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. WORN RINGS OR DILUTED OIL: When the engine is accelerated (dotted needle), the needle
drops to 0 kPa (0 in- Hg). Upon deceleration, the needle runs slightly above 74 kPa (22 in- Hg).
5. STICKING VALVES: When the needle (dotted) remains steady at a normal vacuum but occasionally flicks (sharp, fast movement) down and back about 13 kPa (4 in- Hg), one or more
valves may be sticking.
6. BURNED OR WARPED VALVES: A regular, evenly- spaced, downscale flicking of the needle
indicates one or more burned or warped valves. Insufficient hydraulic lash adjuster or hydraulic
lash adjuster (HLA) clearance will also cause this reaction.
7. POOR VALVE SEATING: A small but regular downscale flicking can mean one or more valves are not seating.
8. WORN VALVE GUIDES: When the needle oscillates over about a 13 kPa (4 in- Hg) range at idle
speed, the valve guides could be worn. As engine speed increases, the needle will become
steady if guides are responsible.
9. WEAK VALVE SPRINGS: When the needle oscillation becomes more violent as engine rpm is increased, weak valve springs are indicated. The reading at idle could be relatively steady.
10. LATE VALVE TIMING: A steady but low reading could be caused by late valve timing.
11. IGNITION TIMING RETARDING: Retarded ignition timing will produce a steady but somewhat low reading.
12. INSUFFICIENT SPARK PLUG GAP: When spark plugs are gapped too close, a regular, small pulsation of the needle can occur.
13. INTAKE LEAK: A low, steady reading can be caused by an intake manifold or throttle body gasket leak.
14. BLOWN HEAD GASKET: A regular drop of fair magnitude can be caused by a blown head gasket or warped cylinder head- to-cylinder block surface.
15. RESTRICTED EXHAUST SYSTEM: When the engine is first started and is idled, the reading may be normal, but as the engine rpm is increased, the back pressure caused by a clogged
muffler (5230), kinked tail pipe or other concerns will cause the needle to slowly drop to 0 kPa
(0 in-Hg). The needle then may slowly rise. Excessive exhaust clogging will cause the needle to
drop to a low point even if the engine is only idling.
16. When vacuum leaks are indicated, search out and correct the cause. Excess air leaking into the system will upset the fuel mixture and cause concerns such as rough idle, missing on
acceleration or burned valves. If the leak exists in an accessory unit such as the power brake
booster (2005), the unit will not function correctly. Always fix vacuum leaks.
Excessive Engine Oil Consumption
The amount of oil an engine uses will vary with the way the vehicle is driven in addition to normal
engine- to-engine variation. This is especially true during the first 16,100 km (10,000 miles) when a new
engine is being broken in or until certain internal engine components become conditioned. Vehicles
used in heavy- duty operation may use more oil. The following are examples of heavy- duty operation:
z trailer towing applications
z severe loading applications
z sustained high speed operation Klj . 12 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Valve Stem to Valve Guide Clearance
NOTE:
Valve stem diameter must be within specifications before checking valve stem to valve guide
clearance.
1. NOTE: If necessary, use a magnetic base.
Install a Valve Guide Clearance Gauge on the valve stem and install a Dial Indicator Gauge with
Holding Fixture. Lower the valve until the Valve Guide Clearance Gauge contacts the upper
surface of the valve guide.
2. Move the Valve Guide Clearance Gauge toward the indicator and zero the indicator. Move the Valve Guide Clearance Gauge away from the indicator and note the reading. The reading will
be DOUBLE the valve stem- to-valve guide clearance. Valves with oversize stems will need to
be installed if out of specification.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Special Tool(s)
Dial Indicator Gauge with
Holding Fixture
100-
002 (TOOL- 4201-C) or
equivalent Clearance Gauge, Valve Guide
303-
004 (TOOL- 6505-E) or
equivalent Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

A/C compressor bracket-
to-cylinder head stud bolt 25 18 —
Oil level indicator tube-
to-cylinder head bolt 10 — 89
Coolant recovery reservoir bracket-to-
GOP bolts 9 — 80
Motor mount-
to-subframe nuts 115 85 —
Oil pan drain plug 26 19 —
Wire harness bracket to motor mount nut 27 20 —
Steering column pinch bolt 47 35 —
Front subframe-
to-body bolts 90 66 —
Front subframe-
to-shock tower bolts 115 85 —
Oil pan-to-
cylinder block bolts a — — —
Oil pan-to-
transmission bell housing 45 33 —
Main bearing bridge nuts 32 24
Oil pump cover-
to-engine front cover bolts 25 18 —
Oil pump cover-
to-engine front cover bolt 10 89 —
Oil pickup tube-
to-cylinder block bolts 25 18 —
Oil pickup tube-
to-oil pan baffle nut 48 35 —
Flywheel-
to-crankshaft bolts 80 59 —
Wire harness bracket-
to-motor mount stud- nut 27 20 —
Engine ground strap-
to-motor mount nut 27 20 —
Motor mount-
to-motor mount bracket bolts 70 52 —
RH motor mount-
to-motor mount bracket nut 70 52 —
Hood ground strap-
to-hood hinge bolt 12 9 —
Hood hinge nuts 12 9 —
Generator mounting bracket 25 18 —
Power steering pump bracket nuts 8 — 71
Power steering pump bolts 25 18 —
Valve tappet guide plate bolts 12 9 —
Generator positive cable nut 10 — 89
Power steering pressure tube to pump nut 40 30 —
Accelerator cable bracket-
to-intake manifold bolts 10 — 89
42-
pin connector bolt 10 — 89
Transmission oil cooler tube bracket-
to-motor mount bracket nut 27 20
Torque converter-
to-flywheel nuts 36 27 —
Engine-
to-transmission bolts 40 30 —
Engine mount bracket-
to-engine bolts 70 52 —
Engine mount bracket-
to-engine nuts 70 52 —
Water pump pulley bolts 25 18 —
Oil filter
b — — —
Upper intake manifold-
to-lower intake manifold bolts a — — —
Lower intake manifold-
to-cylinder head bolts a — — —
Rocker arm pivot-
to-cylinder head bolts a — — — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...