2003 FORD MUSTANG wiring

Anti-Lock Brake Control Module Active Command Index
Symptom Chart Valve
RF_TC_S RF Traction Control Switching
Valve OFF, ON
LR_TC_S LR Traction Control Switching
Valve OFF, ON
RR_TC_S RR Traction Control Switching
Valve OFF, ON
T/ALVAL Left Traction Control Valve
Output State OFF---, OFFO--, OFF
-B-, OFF--G, OFFO- G, OFF-
BG, OFFOBG, ON---, ONO--, ON -B-, ON--G, ONO-
G, ON- BG, ONOBG T/ARVAL Right Traction Control Valve
Output State OFF---, OFFO--, OFF
-B-, OFF--G, OFFO- G, OFF-
BG, OFFOBG, ON---, ONO--, ON -B-, ON--G, ONO-
G, ON- BG, ONOBG
Anti-Lock Brake Control Module Active Command Index Active Command Display Action
ABS OUTPUT CONTROL ABS POWER OFF, ON
DSBL TOG OFF, ON
LF INLET OFF, ON
LF OUTLET OFF, ON
RF INLET OFF, ON
RF OUTLET OFF, ON
LR INLET OFF, ON
LR OUTLET OFF, ON
RR INLET OFF, ON
RR OUTLET OFF, ON
TRACTION CONTROL PRIMARY AND SWITCHING VALVE CONTROL LF TC PRV OFF, ON
LF TC SWV OFF, ON
RF TC PRV OFF, ON
RF TC SWV OFF, ON
LR TC PRV OFF, ON
LR TC SWV OFF, ON
RR TC PRV OFF, ON
RR TC SWV OFF, ON
Symptom Chart
NOTE: Refer to the wiring diagrams for connector numbers stated in the pinpoint Klj . 5 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4 N805572-
S36 Air bag module retaining screws (2 req'd)
5 3L518 Steering wheel spoke cover
(2 req'd)
6 — Lock tabs
7 14A664 Clockspring
8 13318 Turn indicator cancel cam
9 3C610 Snap ring
10 3520 Bearing spring
11 3518 Upper bearing sleeve
12 3517 Upper bearing (small)
13 3517 Lower bearing (large)
14 3524 Shaft assembly
15 390345-
S36 Screw
16 13K359 Multi-
function switch 17 3E695 Lock cam
18 3F609 Tilt wheel handle
19 N806157 Lock cam pivot pin
20 3530 Lower shroud
21 55929 Shroud retaining screws
22 3D544 Release lever
23 3B661 Lock actuator lever (RH)
24 N805856 Lock actuator lever pin
25 3D653 Lock actuator lever (LH)
26 3B664 Lock lever spring (2 req'd)
27 14A099 Wiring shield
28 3D655 Lock lever spring return
29 3E715 Lock lever upper actuator
30 3E696 Lock spring (shaft)
31 11572 Ignition switch
32 N806423-
S56 Steering column mounting lower nuts
33 N806584 Screw
34 3E660 Mounting bracket
35 3D681 Bearing retaining
36 3518 Bearing sleeve
37 3517 Lower bearing
38 3L539 Lower bearing tolerance ring
39 3C131 Sensor ring
40 3520 Bearing spring
41 N808349 Bolt —
flange yoke 42 3N725 Coupling
43 3C611 Tube boot
44 3B676 Intermediate shaft Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Steering Column Switches
Refer to Wiring Diagrams Cell
13 , Power Distribution for schematic and connector information.
Refer to Wiring Diagrams Cell 81 , Interval Wiper/Washer for schematic and connector information.
Refer to Wiring Diagrams Cell 85 , Headlamps for schematic and connector information.
Refer to Wiring Diagrams Cell 90 , Turn/Stop/Hazard Lamps for schematic and connector information.
Inspection and Verification 1. Verify the customer concern by operating the multifunction or ignition switch.
2. Visually inspect for obvious signs of mechanical and electrical damage.
3. If the concern remains after the inspection, connect the scan tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested from the scan
tool menu. If the scan tool does not communicate with the vehicle:
zcheck that the program card is correctly installed.
SECTION 211-
05: Steering Column Switches 2003 Mustang Workshop Manual Special Tool(s)
Worldwide Diagnostic System
(WDS)
418-
F224,
New Generation STAR (NGS)
Tester
418- F052, or equivalent scan
tool 73 Digital Multimeter
105-
R0051 or equivalent
Visual Inspection Chart Mechanical Electrical
z
Ignition key
z Ignition switch
z Multifunction switch
z Turn signal switch
z Hazard/flasher switch z
Battery junction box (BJB) Fuses:
„(3) IGN (40A)
z Central junction box (CJB) Fuses:
„6 (25A)
„ 39 (5A)
z Damaged wiring harness
z Loose or corroded connections Klj . 1 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Symptom Chart
Pinpoint Tests
PINPOINT TEST A: NO COMMUNICATION WITH THE GENERIC
ELECTRONIC MODULE Circuit Failure
B2488 RF Side Repeater Lamp Output
Circuit Failure GEM REFER to
Section 417 - 01 .
C1189 Brake Fluid Level Sensor Input
Short Circuit to Ground GEM REFER to
Section 413 - 01 .
C1223 Lamp Brake Warning Output
Circuit Failure GEM REFER to
Section 413 - 01 .
C1225 Lamp Brake Warning Output
Circuit Short to Battery GEM REFER to
Section 413 - 01 .
Symptom Chart Condition
Possible Sources Action
z No communication with
the generic electronic
module z
CJB Fuse 39
(5A).
z Circuitry.
z GEM. z
Go To Pinpoint Test A .
z The ignition switch is
inoperative z
BJB Fuse IGN
SW (40A).
z Ignition switch.
z Circuitry. z
Go To Pinpoint Test B .
z No power in ACC zIgnition switch.
z Circuitry. z
Go To Pinpoint Test C .
z No power in RUN zIgnition switch.
z Circuitry. z
Go To Pinpoint Test D .
z No power in START zIgnition switch.
z Circuitry. z
Go To Pinpoint Test E .
z The multifunction
switch/hazard switch
does not operate
correctly z
Multifunction
switch. z
Carry out the multifunction
switch component test.
REFER to Wiring Diagrams,
Cell 149, Component
Testing. Test Step Result / Action to Take
CAUTION: Use the correct probe adapter(s) when making measurements. Filaure to
use the correct probe adapter(s) may damage the connector. A1 CHECK THE GENERIC ELECTRONIC MODULE (GEM)
POWER SUPPLY z
Key in OFF position.
z Disconnect: Generic Electronic Module (GEM) C201a. Yes
GO to
A2 . Klj . 4 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST B: THE IGNITION SWITCH IS INOPERATIVE z
Disconnect: GEM C201b.
z Key in ON position.
z Using the following table. measure the voltage between the
GEM, harness side and ground.
z Are the voltages greater than 10 volts? Connector Pin Circuit
C201a 2 400 (LB/BK)
C201a 3 1006 (DG/WH)
C201b 1 1001 (WH/YE)
C201b 4 193 (YE/LG) No
REPAIR the circuit(s) in
question. TEST the system
for normal operation.
A2 CHECK THE GEM GROUND CIRCUIT 397 (BK/WH) FOR
OPEN z
Key in OFF position.
z Measure the resistance between the GEM C201b pin 2,
circuit 397 (BK/WH), harness side and ground.
z Is the resistance less than 5 ohms? Yes
GO to
A3 .
No
REPAIR the circuit(s) in
question. TEST the system
for normal operation. A3 CHECK CIRCUIT 397 (BK/WH) FOR SHORT TO POWER
z
Measure the voltage between GEM C201b pin 2, circuit 397
(BK/WH), harness side and ground.
z Is any voltage present? Yes
REPAIR the circuit. TEST
the system for normal
operation.
No
REFER to
Section 418 - 00 .
Test Step Result / Action to Take
B1 CHECK THE IGNITION SWITCH
z
Carry out the ignition switch component test.
REFER to Wiring Diagrams Cell 149,
Component Testing.
z Is the ignition switch OK ? Yes
INSTALL a new BJB. TEST the system for
normal operation. Klj . 5 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST C: NO POWER IN ACC
PINPOINT TEST D: NO POWER IN RUN
PINPOINT TEST E: NO POWER IN START No
INSTALL a new ignition switch. REFER to
Ignition Switch
. TEST the system for
normal operation. Test Step Result / Action to Take
C1 CHECK THE RADIO FOR NORMAL OPERATION
z
Key in ON position.
z Check the radio for normal operation.
z Does the radio operate correctly? Yes
GO to
C2 .
No
Go To Pinpoint Test D .
C2 CHECK THE VOLTAGE AT THE IGNITION SWITCH
z
Disconnect: Ignition Switch C250 .
z Measure the voltage between ignition switch C250 Pin B5,
Circuit 1050 (LG/VT), harness side and ground.
z Is the voltage greater than 10 volts? Yes
INSTALL a new ignition
switch. REFER to
Ignition Switch . TEST the system for
normal operation.
No
REPAIR the circuit. TEST the
system for normal operation. Test Step Result / Action to Take
D1 CHECK THE IGNITION SWITCH
z
Carry out the ignition switch component test.
REFER to Wiring Diagrams Cell 149,
Component Testing.
z Is the ignition switch OK ? Yes
INSTALL a new BJB. TEST the system for
normal operation.
No
INSTALL a new ignition switch. REFER to
Ignition Switch
. TEST the system for
normal operation. Test Step Result / Action to Take
E1 CHECK THE VOLTAGE TO THE IGNITION SWITCH
z
Key in OFF position.
z Disconnect: Ignition Switch C250 . Yes
GO to
E2 . Klj . 6 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Component Test
Ignition Switch Continuity Check
Refer to Wiring Diagrams Cell 149, Component Testing.
Multifunction Switch
Refer to Wiring Diagrams Cell 149, Component Testing. z
Measure the voltage between ignition switch C250 Pin B4,
Circuit 1050 (LG/VT), harness side and ground; and between
ignition switch C250 Pin B5, Circuit 1050 (LG/VT), harness side
and ground.
z Are the voltages greater than 10 volts? No
REPAIR the circuit in
question.TEST system
for normal operation.
E2 CHECK THE CONTINUITY OF THE IGNITION SWITCH
z
Carry out the ignition switch continuity test. REFER to Wiring
Diagrams, Cell 149, Component Testing.
z Does the ignition switch test OK? Yes
GO to
E3 .
No
INSTALL a new ignition
switch. REFER to
Ignition Switch . TEST
the system for normal
operation. E3 CHECK CIRCUIT 16 (RD/LB), AND CIRCUIT 33 (WH/PK)
z
Connect: Ignition Switch C250.
z Turn ignition switch to START.
z Does the starter engage? Yes
REPAIR Circuit 16
(RD/LB). TEST the
system for normal
operation.
No
REPAIR Circuit 33
(WH/PK). TEST the
system for normal
operation. Klj . 7 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

12. Disconnect the crankshaft position sensor electrical connector.
13. Remove the wiring harness pin-
type retainer.
14. Remove the oil filter.
15. Remove the retainers and the water pump. Klj . 3 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...