2003 FORD MUSTANG wheel

2. Check wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 -
00 . Klj . 3 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Wheel Knuckle —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
4. Remove and discard the rear hub retainer (4B477).
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Front Hub Remover
205-
D070 (D93P-1175- B) or
Equivalent Steering Arm Remover
211-
003 (T64P-9171- A) Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

17. Remove the dust shield, hub, snap ring and bearing from the knuckle. For additional
information, refer to Wheel Hub — Cobra in this section.
Installation
1. Install the bearing, snap ring, hub and dust shield. For additional information, refer to Wheel Hub — Cobra in this section.
2. Install the knuckle. 1. Position the knuckle on the lower suspension arm and bushing.
2. Install a new bolt and a new nut. Do not tighten the nut at this time.
3. Connect the axle shaft to the hub. 1. Making sure the splines on the shaft line up with the splines in the hub, install the axle
shaft into the hub.
2. Install a new retainer. Do not tighten the retainer at this time.
4. Connect the upper suspension arm and bushing to the knuckle. 1. Position the upper suspension arm and bushing on the knuckle.
2. Install a new cam bolt and a new nut. Do not tighten the nut at this time. Klj . 5 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Connect the parking brake cable and conduit to the rear brake caliper and install the clip.
14. Connect the parking brake cable and conduit to the parking brake lever.
15.
CAUTION: The axle retainer must be tightened with the brakes applied and the
wheels off the ground to make sure of correct bearing seating. Failure to do so can
cause the retainer to loosen, causing extensive vehicle damage and loss of vehicle
control.
Lower the vehicle and apply the parking brake or service brakes.
16. Tighten the retainer.
17. Install the wheel and tire assembly. For additional information, refer to Section 204 - 04
18. Lower the vehicle.
19. Check the wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 - 00 . Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Toe Link —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the rear brake disc. For additional information, refer to Section 206 - 04 .
4. Support the lower suspension arm and bushing (5A649) with a jack stand.
5. Remove the nut and bolt and disconnect the shock absorber (18125) from the lower suspension arm and bushing. Discard the nut and bolt.
6. Remove and discard the cotter pin and nut.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Steering Arm Remover
211-
003 (T64P-9171- A) Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Check wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 -
00 . Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Support the No. 1 crossmember with a jack stand.
3. Remove both wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
4. Remove both mufflers. For additional information, refer to Section 309 - 00 .
5. Remove the driveshaft. For additional information, refer to Section 205 - 01 .
6. Disconnect the parking brake cable and conduits from the parking brake levers.
7. Remove the clip and disconnect the parking brake cable and conduits from the rear brake calipers. SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Rotunda Powertrain Lift
014-00765 or Equivalent Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

15. Connect the parking brake cable and conduit to the parking brake levers.
16. Install the driveshaft. For additional information, refer to
Section 205 - 01 .
17. Install both mufflers. For additional information, refer to Section 309 - 00 .
18. Install both wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
19. Remove the jack stand from the No. 1 crossmember.
20. Bleed the brake system. For additional information, refer to Section 206 - 00 .
21. Check wheel alignment. Adjust if necessary. For additional information, refer to Section 204 - 00 . Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...