2003 FORD MUSTANG wheel

Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Remove the rear wheel knuckle (5A968/5A969). For additional information, refer to Wheel Knuckle — Cobra in this section.
2. Remove the bolts and the dust shield. Discard the bolts.
3. Position the knuckle in a vise.
4. NOTE: There are two methods for removing the rear hub (1109) from the rear wheel bearing
(1A049). Both methods are shown.
Method one. Using the special tools, remove the hub. Step Plate Adapter Set
205-
DS011 (D80L-630- A) or
Equivalent Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Method two. Using the special tools, remove the hub.
6. Remove the snap ring.
7. Press the wheel bearing from the knuckle.
1. Position the knuckle on the press bed supported by the special tool.
2. Using the appropriate step plate adapter, press the bearing from the knuckle.
Installation 1. Install the bearing. 1. Position the knuckle on the press.
2. Using the appropriate step plate adapter, press the bearing into the knuckle until the bearing clears the snap ring groove and bottoms out in the bore. Klj . 3 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Install the snap ring.
3.
CAUTION: The bearing inner race must be supported during hub installation.
Failure to follow these instructions can damage the bearing.
Install the hub. 1. Position the knuckle in a press, making sure the wheel bearing inner race is supported with the appropriate step plate adapter.
2. Using the special tool, install the hub. 4. Install the dust shield and new bolts. Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Inspect the bearing dust seal. If necessary, install a new dust seal.
6. Using a hammer and chisel, remove the dust seal.
7. Using the special tools, install the dust seal.
8. Install the knuckle. For additional information, refer to
Wheel Knuckle — Cobra in this section. Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Wheel Studs
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the rear brake disc. For additional information, refer to Section 206 - 04 .
4. Using the special tool, remove and discard the wheel stud.
Installation CAUTION: Do not use air tools to install the wheel stud. The serrations in the hub flange
can be stripped.
1. Install the wheel stud. 1. Position a new wheel stud in the hub flange making sure the serrations on the stud line up with the serrations in the flange.
2. Position washers and a reversed wheel nut on the wheel stud.
3. Tighten the wheel nut until the wheel stud seats on the back of the hub flange.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
C-
Frame and Clamp Assembly
211- 023 (T74P-3044- A1) Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Remove the wheel nut and washers. Discard the nut.
3. Install the rear brake disc. For additional information, refer to
Section 206 - 04 .
4. Install the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
5. Lower the vehicle. Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Upper Arm —
Cobra
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove both wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
4. Remove the rear brake disc. For additional information, refer to Section 206 - 04 .
5. Remove the rear springs (5560). For additional information, refer to Spring — Cobra in this
section.
6. Raise the subframe into position and remove the front bolts.
7. Lower the subframe from the vehicle.
8. Mark the cam bolt position relative to the upper suspension arm and bushing (5500).
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

7. Tighten the nuts.
8. Position the cam bolt so the marks are aligned. Tighten the nut.
9. Lower the suspension and remove the jack stand.
10. Install the rear brake disc. For additional information, refer to Section 206 - 04 .
11. Install the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
12. Lower the vehicle.
13. Check wheel alignment, adjust if necessary. For additional information, refer to Section 204 - 00 . Klj . 4 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...