2003 FORD MUSTANG wheel

GENERAL PROCEDURES
Brake Disc Machining
WARNING: The electrical power to the air suspension system must be shut off prior to
hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off
the air suspension switch. Failure to do so can result in unexpected inflation or deflation of the
air springs, which can result in shifting of the vehicle during these operations.
CAUTION: Do not install brake discs that are less than the minimum thickness specified.
Do not machine a brake disc below the minimum thickness specification.
1. Check wheel bearing end- play and correct as necessary.
2. NOTE: Begin at the front of the vehicle unless the vibration has been isolated to the rear.
Remove the tire and wheel assembly.
3. Remove the brake caliper and the brake caliper anchor plate. Refer to the appropriate section in Group 206 for the procedure.
4. Inspect the brake linings. Install new brake linings if below specification. For additional information, refer to the appropriate brake section.
5. Measure and record the brake disc thickness. Install a new brake disc if the thickness after machining will be at or below specification. The specification is molded into the brake disc.
zDo not machine a new brake disc.
SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Special Tool(s)
Gauge, Clutch Housing
308-
021 (T75L-4201- A) Dial Indicator Gauge with
Holding Fixture
100-
002 (TOOL- 4201-C) or
equivalent
Material Item Specification
Metal Surface Cleaner
F4AZ-
19A536- RA or equivalent WSE-
M5B392-
A High Temperature Nickel Anti-
Seize Lubricant
F6AZ-
9L494- AA or equivalent ESE-
M12A4-A Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. For vehicles with a two-
piece hub and brake disc assembly:
z Match-mark before disassembly.
z Remove the brake disc.
z Clean the hub and brake disc mounting surfaces with metal surface cleaner.
z Using a die grinder with a mild abrasive (Scotch Brite® type), remove any rust or
corrosion from the hub and brake disc mounting surfaces.
z Align the match- marks and reinstall the brake disc on the hub.
7. CAUTION: Do not use a bench lathe to machine brake discs.
NOTE: The depth of cut must be between 0.10 and 0.20 mm (0.004 and 0.008 inch). Lighter
cuts will cause heat and wear. Heavier cuts will cause poor brake disc surface finish.
Using an on- car brake lathe, machine the brake discs. Follow the manufacturer's instructions.
After machining, make sure the brake disc still meets the thickness specification.
8. Using the special tools, verify that the brake disc lateral runout is now within specification. For additional information, refer to Section 206 - 00 .
9. Remove the special tool hub adapter.
10. Remove any remaining metal chips from the machining operation.
11. For vehicles with a two- piece hub and brake disc assembly:
z Remove the brake disc from the hub.
z Remove any remaining metal chips from hub and brake disc mounting surfaces and from
the ABS sensor.
z Apply a liberal amount of lubricant to the hub flange, pilot area and to the brake disc- to-
hub mounting surface.
z Using the match marks, mount the brake disc on the hub.
12. Install the brake caliper anchor plate and the brake caliper.
13. Install the tire and wheel assembly.
14. Test the system for normal operation. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Wheel Bearing Check
1. WARNING: The electrical power to the air suspension system must be shut off prior
to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by
turning off the air suspension switch. Failure to do so can result in unexpected inflation
or deflation of the air springs, which can result in shifting of the vehicle during these
operations.
Raise the vehicle until the front tires are off the floor.
zMake sure the wheels are in a straight forward position.
2. NOTE: Make sure the wheel rotates freely and that the brake pads are retraced sufficiently to
allow free movement of the tire and wheel assembly.
Spin the tire by hand to check the wheel bearings for roughness.
3. Grip each front tire at the top and bottom and move the wheel inward and outward while lifting the weight of the tire off the front wheel bearing.
4. If the tire and wheel (hub) is loose on the spindle, does not rotate freely, or has a rough feeling when spun, carry out one of the following:
1. On vehicles with inner and outer bearings, inspect the bearings and cups for wear or damage. Adjust or install new bearings and cups as necessary.
2. On vehicles with one sealed bearing, install a new wheel hub.
SECTION 100-
04: Noise, Vibration and Harshness 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Wheel Alignment Angles
Camber and toe are adjustable on the front suspension systems. Front camber is adjusted by moving
the top of the strut and spring assembly. Rear camber is adjusted by means of eccentric cams on the
rear upper arms. Caster is preset at the factory and should only be adjusted after all other possible
sources have been inspected and corrected as necessary. Front toe is adjusted by the use of the front
wheel spindle tie rod (3280).
Camber
Negative and Positive Camber
Camber is the vertical tilt of the wheel (1007) when viewed from the front. Camber can be positive or
negative and has a direct effect on tire wear.
Caster
Caster is the deviation from vertical of an imaginary line drawn through the ball joints when viewed
from the side. Caster specifications in this section will give the vehicle the best directional stability
characteristics when loaded and driven. Caster setting is not related to tire wear.
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Item Part Number Description
1 — Positive caster
2 — True vertical
3 — Steering axis Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Wheel Track
Dogtracking
Dogtracking or thrust angle is the condition in which the rear axle is not square to the chassis. Heavily
crowned roads can give the illusion of dogtracking.
Wander
Wander is the tendency of the vehicle to require frequent, random left and right steering wheel (3600)
corrections to maintain a straight path down a level road. Item Description
1 Body reinforcement
2 Ride height (shortest distance)
3 Rear axle
Item Part Number Description
1 — Front track
2 — Rear track
Item Part Number Description
1 — Vehicle centerline
2 — Axle centerline
3 — Thrust angle Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Shimmy
Shimmy, as observed by the driver, is large, consistent, rotational oscillations of the steering wheel
resulting from large, side-
to-side (lateral) tire/wheel movements.
Shimmy is usually experienced near 64 km/h (40 mph), and can begin or be amplified when the tire
contacts pot holes or irregularities in the road surface.
Nibble
Sometimes confused with shimmy, nibble is a condition resulting from tire interaction with various road
surfaces and observed by the driver as small rotational oscillations of the steering wheel.
Poor Returnability/Sticky Steering
Poor returnability and sticky steering is used to describe the poor return of the steering wheel to center
after a turn or steering correction is completed.
Drift/Pull
Pull is a tugging sensation, felt in the steering wheel, that must be overcome to keep the vehicle going
straight.
Drift describes what a vehicle with this condition does with hands off the steering wheel.
zDrift/pull may be induced by conditions external to the vehicle (i.e., wind, road camber).
Poor Groove Feel
Poor groove feel is characterized by little or no buildup of turning effort felt in the steering wheel as the
wheel is rocked slowly left and right within very small turns around center or straight- ahead (under 20
degrees of steering wheel turn). Efforts may be said to be "flat on center."
zUnder 20 degrees of turn, most of the turning effort that builds up comes from the mesh of gear
teeth in the steering gear (3504). In this range, the steering wheel is not yet turned enough to
feel the effort from the self- aligning forces at the road wheel or tire patch.
z In the diagnosis of a handling problem, it is important to understand the difference between
wander and poor groove feel. Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Suspension System
Inspection and Verification
1. Road test. zVerify the customer's concern by performing a road test on a smooth road.
2. Inspect tires. zCheck the tire pressure with all normal loads in the vehicle and the tires cold. For
additional information, refer to the vehicle certification (VC) label.
z Verify that all tires are sized to specification.
z Inspect the tires for incorrect wear and damage.
3. Inspect chassis and underbody. zRemove any excessive accumulation of mud, dirt or road deposits from the chassis and
underbody.
4. Inspect for aftermarket equipment. zCheck for aftermarket changes to the steering, suspension, wheel and tire components
(such as competition, heavy duty, etc.) The specifications shown in this manual do not
apply to vehicles equipped with aftermarket equipment.
5. Inspect shock absorbers. All vehicles are equipped with gas- pressurized hydraulic shock absorbers. These shock
absorbers are not adjustable or refillable and cannot be repaired.
zOil Leak: A light film of oil (weepage) on the upper portion of the shock absorber is
permissible and is a result or correct shock lubrication. Weepage is a condition in which a
film of oil accumulates on the thin tube (body) and is normally noticed due to the
collection of dust in this area. If shock absorbers exhibit this weepage condition, they are
functional units and new shock absorbers should not be installed. Leakage is a condition
in which the entire shock absorber body is covered with oil and the oil will drip from the
shock absorber onto the pavement. If condition exists:
„Make sure fluid observed is not from sources other than the shock absorber.
„ Install a new shock absorber, if necessary.
z Vehicle Sag: Many times new shock absorbers are installed in an effort to solve a vehicle
sag concern. Shock absorbers by design are hydraulic damping units only and, unlike
suspension springs, do not support any suspension loads. Therefore, installing a new
shock absorber will not correct a vehicle sag concern.
z Installment in Pairs: In the past it was recommended that new shock absorbers be
installed in pairs if one unit became unrepairable. New shock absorbers no longer need
to be installed in pairs when only one unit is not repairable.
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Visual Inspection Chart
Mechanical Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. If an obvious cause for an observed or reported condition is found, correct the cause (if
possible) before proceeding to the next step.
7. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .
Symptom Chart z
Front wheel bearing(s)
z Loose or damaged front or rear suspension components
z Loose, damaged or missing suspension fastener(s)
z Damaged spring(s)
z Damaged or leaking strut and spring assemblies
z Damaged or leaking shock absorber(s)
z Worn or damaged suspension bushing(s)
z Loose, worn or damaged steering system components
z Damaged axle components
Symptom Chart Condition
Possible Sources Action
z Dogtracking zExcessive rear
thrust angle. z
CHECK the wheel alignment.
ADJUST as necessary.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Drive axle
damaged. z
REPAIR as necessary. Refer
to the appropriate section in
Group 205 for the procedure..
z Drift/pull zUnequal tire
pressure. z
ADJUST tire pressure.
z Excessive side-to-
side difference in
caster or camber. z
CHECK the wheel alignment.
ADJUST as necessary.
z Tire forces. zROTATE tires front to rear.
z Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Steering
components. z
REFER to Section 211 - 00 .
z Brake drag. zREFER to Section 206 - 00 .
z Front bottoming
or riding low z
Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Front coil springs
(5310). z
CHECK ride height. INSTALL
new springs as necessary.
REFER to Section 204 - 01 .
z Incorrect tire
wear z
Incorrect tire
pressure (rapid
center rib or inner
and outer edge
wear). z
ADJUST tire pressure. Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...