2003 DODGE RAM radiator cap

²internal failure that generates debris
²overheat that generates sludge (fluid break-
down)
²failure to replace contaminated converter after
repair
The use of non-recommended fluids can result in
transmission failure. The usual results are erratic
shifts, slippage, abnormal wear and eventual failure
due to fluid breakdown and sludge formation. Avoid
this condition by using recommended fluids only.
The dipstick cap and fill tube should be wiped
clean before checking fluid level. Dirt, grease and
other foreign material on the cap and tube could fall
into the tube if not removed beforehand. Take the
time to wipe the cap and tube clean before withdraw-
ing the dipstick.
Engine coolant in the transmission fluid is gener-
ally caused by a cooler malfunction. The only remedy
is to replace the radiator as the cooler in the radiator
is not a serviceable part. If coolant has circulated
through the transmission, an overhaul is necessary.
The torque converter should be replaced whenever
a failure generates sludge and debris. This is neces-
sary because normal converter flushing procedures
will not remove all contaminants.
STANDARD PROCEDURE
STANDARD PROCEDURE - FLUID LEVEL
CHECK
Low fluid level can cause a variety of conditions
because it allows the pump to take in air along with
the fluid. As in any hydraulic system, air bubbles
make the fluid spongy, therefore, pressures will be
low and build up slowly.
Improper filling can also raise the fluid level too
high. When the transmssion has too much fluid, the
geartrain churns up foam and cause the same condi-
tions which occur with a low fluid level.
In either case, air bubbles can cause overheating
and/or fluid oxidation, and varnishing. This can
interfere with normal valve, clutch, and accumulator
operation. Foaming can also result in fluid escaping
from the transmission vent where it may be mis-
taken for a leak.
After the fluid has been checked, seat the dipstick
fully to seal out water and dirt.
The transmission has a dipstick to check oil level.
It is located on the right side of the engine. Be sure
to wipe all dirt from dipstick handle before removing.
The torque converter fills in both the P (PARK)
and N (NEUTRAL) positions. Place the selector lever
in P (PARK) to be sure that the fluid level check is
accurate.The engine should be running at idle
speed for at least one minute, with the vehicleon level ground.At normal operating temperature
(approximately 82 C. or 180 F.), the fluid level is cor-
rect if it is in the HOT region (cross-hatched area) on
the oil level indicator. The fluid level will be approx-
imately at the upper COLD hole of the dipstick at
70É F fluid temperature.
NOTE: Engine and Transmission should be at nor-
mal operating temperature before performing this
procedure.
(1) Start engine and apply parking brake.
(2) Shift the transmission into DRIVE for approxi-
mately 2 seconds.
(3) Shift the transmission into REVERSE for
approximately 2 seconds.
(4) Shift the transmission into PARK.
(5) Hook up DRBtscan tool and select transmis-
sion.
(6) Select sensors.
(7) Read the transmission temperature value.
(8) Compare the fluid temperature value with the
chart. (Fig. 66)
(9) Adjust transmission fluid level shown on the
dipstick according to the chart.
NOTE: After adding any fluid to the transmission,
wait a minimum of 2 minutes for the oil to fully
drain from the fill tube into the transmission before
rechecking the fluid level.
(10) Check transmission for leaks.
STANDARD PROCEDURE - FLUID AND FILTER
REPLACEMENT
For proper service intervals (Refer to LUBRICA-
TION & MAINTENANCE/MAINTENANCE SCHED-
ULES - DESCRIPTION).
REMOVAL
(1) Hoist and support vehicle on safety stands.
(2) Place a large diameter shallow drain pan
beneath the transmission pan.
(3) Remove bolts holding front and sides of pan to
transmission.
(4) Loosen bolts holding rear of pan to transmis-
sion.
(5) Slowly separate front of pan away from trans-
mission allowing the fluid to drain into drain pan.
(6) Hold up pan and remove remaining bolts hold-
ing pan to transmission.
(7) While holding pan level, lower pan away from
transmission.
(8) Pour remaining fluid in pan into drain pan.
(9) Remove screw holding filter to valve body (Fig.
67).
21 - 542 AUTOMATIC TRANSMISSION - 45RFE/545RFEDR
FLUID AND FILTER (Continued)

HEATING & AIR CONDITIONING
TABLE OF CONTENTS
page page
HEATING & AIR CONDITIONING
DESCRIPTION
DESCRIPTION - HEATER AND AIR
CONDITIONER........................1
DESCRIPTION - COOLING SYSTEM
REQUIREMENTS.......................1
DESCRIPTION - REFRIGERANT SYSTEM
SERVICE PORT........................1
OPERATION
OPERATION - HEATER AND AIR
CONDITIONER........................1
OPERATION - REFRIGERANT SYSTEM
SERVICE PORT........................2DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - A/C
PERFORMANCE.......................2
DIAGNOSIS AND TESTING - HEATER
PERFORMANCE.......................5
STANDARD PROCEDURE - DIODE
REPLACEMENT.......................7
SPECIFICATIONS
A/C APPLICATION TABLE................7
SPECIFICATIONS......................8
CONTROLS.............................9
DISTRIBUTION..........................24
PLUMBING.............................31
HEATING & AIR
CONDITIONING
DESCRIPTION
DESCRIPTION - HEATER AND AIR
CONDITIONER
All vehicles are equipped with a common HVAC
housing assembly (Fig. 1). The system combines air
conditioning, heating, and ventilating capabilities in
a single unit housing mounted under the instrument
panel.
DESCRIPTION - COOLING SYSTEM
REQUIREMENTS
To maintain the performance level of the HVAC
system, the engine cooling system must be properly
maintained. The use of a bug screen is not recom-
mended. Any obstructions in front of the radiator or
condenser will reduce the performance of the air con-
ditioning and engine cooling systems.
The engine cooling system includes the heater core
and the heater hoses. Refer to Engine Cooling for
more information before the opening of, or attempt-
ing any service to the engine cooling system.
DESCRIPTION - REFRIGERANT SYSTEM
SERVICE PORT
The two refrigerant system service ports are used
to charge, recover/recycle, evacuate, and test the air
conditioning refrigerant system. Unique service port
coupler sizes are used on the R-134a system, toensure that the refrigerant system is not accidentally
contaminated by the use of the wrong refrigerant
(R-12), or refrigerant system service equipment.
OPERATION
OPERATION - HEATER AND AIR CONDITIONER
The heater air conditioner are blend-air type sys-
tems. In a blend-air system, a blend door controls the
amount of unconditioned air (or cooled air from the
evaporator on models with air conditioning) that is
allowed to flow through, or around, the heater core. A
temperature control knob on the A/C Heater control
panel determines the discharge air temperature by
controlling an electric actuator, which moves the
blend door. This allows an almost immediate control
of the output air temperature of the system.
The mode control knob on the A/C Heater control
panel is used to direct the conditioned air to the
selected system outlets. Both mode control switches
use electric actuators to control the mode doors.
On all vehicles, the outside air intake can be shut
off by selecting the Recirculation Mode with the
mode control knob. This will operate a electric actu-
ated recirculation door that closes off the outside
fresh air intake and recirculates the air that is
already inside the vehicle.
The air conditioner for all models is designed for
the use of non-CFC, R-134a refrigerant. The air con-
ditioning system has an evaporator to cool and dehu-
midify the incoming air prior to blending it with the
heated air. This air conditioning system uses a fixed
orifice tube in the liquid line near the condenser out-
let tube to meter refrigerant flow to the evaporator
DRHEATING & AIR CONDITIONING 24 - 1

BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-2
BRAKE TRANSMISSION SHIFT
INTERLOCK - ADJUSTMENTS . . . 21-195,21-376,
21-540
BRAKE TRANSMISSION SHIFT
INTERLOCK - DIAGNOSIS AND
TESTING..............21-195,21-375,21-540
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION . . . 21-194,
21-375,21-540
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION.....21-194,
21-375,21-540
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-18
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-19
BRAKES - ABS - DESCRIPTION...........5-39
BRAKES - ABS - OPERATION............5-39
BRAKES, SPECIAL TOOLS - BASE.........5-5
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-10
BREATHER - INSTALLATION,
CRANKCASE........................9-292
BREATHER - REMOVAL, CRANKCASE.....9-291
BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT BELT................8O-34
BUCKLE - REMOVAL, FRONT OUTBOARD
SEAT BELT .........................8O-33
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE........................8F-10
BUMPER - INSTALLATION, FRONT........13-2
BUMPER - INSTALLATION, JOUNCE.......2-40
BUMPER - INSTALLATION, REAR.........13-4
BUMPER - REMOVAL, FRONT............13-2
BUMPER - REMOVAL, JOUNCE...........2-40
BUMPER - REMOVAL, REAR.............13-4
BUMPERS (3500) - INSTALLATION,
AUXILIARY SPRING....................2-40
BUMPERS (3500) - REMOVAL,
AUXILIARY SPRING....................2-40
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF....21-201,21-381,21-541
BUSHING - INSTALLATION.............19-18
BUSHING - INSTALLATION,
DISTRIBUTOR.......................9-258
BUSHING - INSTALLATION, EXTENSION
HOUSING..........................21-200
BUSHING - INSTALLATION, TORSION
BAR CROSS MEMBER..................2-14
BUSHING - REMOVAL.................19-18
BUSHING - REMOVAL, DISTRIBUTOR.....9-258
BUSHING - REMOVAL, EXTENSION
HOUSING..........................21-200
BUSHING - REMOVAL, TORSION BAR
CROSSMEMBER......................2-12
BUSHING AND SEAL - INSTALLATION,
EXTENSION HOUSING..........21-616,21-682
BUSHING AND SEAL - REMOVAL,
EXTENSION HOUSING..........21-616,21-682
BUSHINGS - 2WD (LD) - INSTALLATION,
LOWER CONTROL ARM................2-14
BUSHINGS - 2WD (LD) - REMOVAL,
LOWER CONTROL ARM................2-12
BUSHINGS - 4WD (LD) - INSTALLATION,
LOWER CONTROL ARM
................2-13
BUSHINGS - 4WD (LD) - REMOVAL,
LOWER CONTROL ARM
................2-12
BUSHINGS - INSTALLATION
.............2-39
BUSHINGS - REMOVAL
.................2-39
BUZZ, SQUEAK & RATTLE - STANDARD
PROCEDURE
........................23-11
BYPASS - DESCRIPTION, WATER PUMP
. . . 7-64
BYPASS - OPERATION, WATER PUMP
.....7-65
BYPASS HOSE WITH AIR CONDITIONING
- INSTALLATION, WATER PUMP
..........7-70
BYPASS HOSE WITH AIR CONDITIONING
- REMOVAL, WATER PUMP
..............7-68
BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER PUMP
........................7-70
BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER
PUMP
..............................7-69
C205F - ADJUSTMENTS, FRONT AXLE
.....3-21
C205F - DESCRIPTION, FRONT AXLE
......3-18C205F - DIAGNOSIS AND TESTING,
FRONT AXLE.........................3-18
C205F - INSTALLATION, FRONT AXLE.....3-21
C205F - OPERATION, FRONT AXLE........3-18
C205F - REMOVAL, FRONT AXLE.........3-21
C205F - SPECIAL TOOLS, FRONT AXLE....3-30
C205F - SPECIFICATIONS, FRONT AXLE....3-29
CAB - INSTALLATION, QUAD...........8O-32
CAB - INSTALLATION, STANDARD.......8O-31
CAB - REMOVAL, QUAD...............8O-29
CAB - REMOVAL, STANDARD...........8O-28
CAB BACK PANEL TRIM -
INSTALLATION, REAR.................23-70
CAB BACK PANEL TRIM - REMOVAL,
REAR..............................23-70
CAB CLEARANCE LAMP - INSTALLATION . . 8L-10
CAB CLEARANCE LAMP - REMOVAL.....8L-10
CABLE - ADJUSTMENTS, THROTTLE
VALVE ......................21-255,21-432
CABLE - DESCRIPTION.................8P-3
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DESCRIPTION, SPARK PLUG.....8I-33
CABLE - DESCRIPTION, THROTTLE
VALVE ......................21-254,21-432
CABLE - DIAGNOSIS AND TESTING,
ANTENNA BODY......................8A-4
CABLE - DIAGNOSIS AND TESTING,
GEARSHIFT............21-209,21-389,21-544
CABLE - INSTALLATION..................8P-6
CABLE - INSTALLATION, ANTENNA BODY . . 8A-6
CABLE - INSTALLATION, CHECK.........23-15
CABLE - INSTALLATION, FRONT
PARKING BRAKE......................5-32
CABLE - INSTALLATION, GEARSHIFT....21-210,
21-390,21-545
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-7
CABLE - INSTALLATION, LEFT REAR......5-33
CABLE - INSTALLATION, REAR PARK
BRAKE..............................5-32
CABLE - INSTALLATION, RIGHT REAR.....5-32
CABLE - INSTALLATION, SPARK PLUG....8I-35
CABLE - INSTALLATION, THROTTLE
CONTROL.....................14-51,14-96
CABLE - OPERATION...................8P-3
CABLE - OPERATION, ANTENNA BODY.....8A-4
CABLE - OPERATION, SPARK PLUG.......8I-33
CABLE - REMOVAL....................8P-3
CABLE - REMOVAL, ANTENNA BODY......8A-6
CABLE - REMOVAL, CHECK.............23-15
CABLE - REMOVAL, FRONT PARKING
BRAKE..............................5-31
CABLE - REMOVAL, GEARSHIFT . 21-209,21-389,
21-544
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-6
CABLE - REMOVAL, LEFT REAR..........5-32
CABLE - REMOVAL, REAR PARK BRAKE . . . 5-31
CABLE - REMOVAL, RIGHT REAR.........5-31
CABLE - REMOVAL, SPARK PLUG........8I-34
CABLE - REMOVAL, THROTTLE
CONTROL.....................14-49,14-94
CABLE, ADJUSTMENTS - GEARSHIFT . . . 21-211,
21-391,21-546
CABLE ORDER, 8.0L V-10 ENGINE -
SPARK PLUG.........................8I-5
CABLE RESISTANCE, SPECIFICATIONS -
SPARK PLUG.........................8I-5
CABLE ROUTING, 5.7L V-8 ENGINE -
FIRING ORDER........................8I-4
CABLE/HANDLE ASSEMBLY -
INSTALLATION, LATCH RELEASE........23-47
CABLE/HANDLE ASSEMBLY - REMOVAL,
LATCH RELEASE.....................23-47
CABLES - DESCRIPTION, BATTERY.......8F-14
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-15
CABLES - DIAGNOSIS AND TESTING,
SPARK PLUG........................8I-33
CABLES - INSTALLATION, BATTERY......8F-17
CABLES - OPERATION, BATTERY........8F-14
CABLES - REMOVAL, BATTERY
..........8F-16
CALIBRATION - STANDARD PROCEDURE,
COMPASS
...........................8M-3
CALIPER ADAPTER MOUNT -
INSTALLATION, DISC BRAKE
............5-17
CALIPERS - DESCRIPTION, DISC BRAKE
. . . 5-11
CALIPERS - OPERATION, DISC BRAKE
.....5-12CAM BORE REPAIR - STANDARD
PROCEDURE........................9-315
CAMBER AND CASTER ADJUSTMENT -
STANDARD PROCEDURE.................2-4
CAMBER, CASTER AND TOE
ADJUSTMENT - STANDARD
PROCEDURE..........................2-4
CAM/OVERDRIVE PISTON RETAINER -
ASSEMBLY, OVERRUNNING CLUTCH....21-239,
21-416
CAM/OVERDRIVE PISTON RETAINER -
CLEANING, OVERRUNNING CLUTCH....21-238,
21-416
CAM/OVERDRIVE PISTON RETAINER -
DESCRIPTION, OVERRUNNING CLUTCH . 21-237,
21-415
CAM/OVERDRIVE PISTON RETAINER -
DISASSEMBLY, OVERRUNNING
CLUTCH.....................21-238,21-415
CAM/OVERDRIVE PISTON RETAINER -
INSPECTION, OVERRUNNING CLUTCH . . 21-238,
21-416
CAM/OVERDRIVE PISTON RETAINER -
OPERATION, OVERRUNNING CLUTCH . . . 21-237,
21-415
CAMSHAFT - INSTALLATION . 9-201,9-250,9-320,
9-381
CAMSHAFT - REMOVAL.....9-200,9-250,9-317,
9-380
CAMSHAFT BEARINGS - INSTALLATION . . 9-320,
9-381
CAMSHAFT BEARINGS - REMOVAL . 9-317,9-380
CAMSHAFT CORE HOLE PLUG -
INSTALLATION.......................9-201
CAMSHAFT CORE HOLE PLUG -
REMOVAL............................9-200
CAMSHAFT POSITION SENSOR -
DESCRIPTION.......................14-82
CAMSHAFT POSITION SENSOR -
DESCRIPTION.........................8I-8
CAMSHAFT POSITION SENSOR -
INSTALLATION.......................14-83
CAMSHAFT POSITION SENSOR -
INSTALLATION.......................8I-14
CAMSHAFT POSITION SENSOR -
OPERATION.........................14-82
CAMSHAFT POSITION SENSOR -
OPERATION..........................8I-8
CAMSHAFT POSITION SENSOR -
REMOVAL..........................14-83
CAMSHAFT POSITION SENSOR -
REMOVAL...........................8I-11
CAMSHAFT(S) - DESCRIPTION.......9-24,9-34
CAMSHAFT(S) - INSTALLATION......9-25,9-35
CAMSHAFT(S) - LEFT - DESCRIPTION....9-113
CAMSHAFT(S) - LEFT - INSTALLATION....9-114
CAMSHAFT(S) - LEFT - REMOVAL.......9-113
CAMSHAFT(S) - REMOVAL..........9-24,9-34
CAMSHAFT(S) - RIGHT - DESCRIPTION . . . 9-117
CAMSHAFT(S) - RIGHT - INSTALLATION . . 9-118
CAMSHAFT(S) - RIGHT - REMOVAL......9-117
CANISTER - DESCRIPTION, VAPOR......25-22
CANISTER - INSTALLATION, VAPOR......25-23
CANISTER - OPERATION, VAPOR........25-22
CANISTER - REMOVAL, VAPOR..........25-22
CAP - 5.9L V-8 - DIAGNOSIS AND
TESTING, DISTRIBUTOR...............8I-18
CAP - DESCRIPTION, FUEL FILLER.......25-13
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-60
CAP - DIAGNOSIS AND TESTING,
RADIATOR...........................7-61
CAP - OPERATION, FUEL FILLER........25-13
CAP - OPERATION, RADIATOR
PRESSURE..........................7-61
CAPACITIES, SPECIFICATIONS - FLUID......0-5
CAPACITOR - DESCRIPTION, IGNITION
COIL...............................8I-33
CAPACITOR - INSTALLATION, IGNITION
COIL...............................8I-33
CAPACITOR - OPERATION, IGNITION
COIL
...............................8I-33
CAPACITOR - REMOVAL, IGNITION COIL
. . . 8I-33
CAPACITY - SPECIFICATIONS, CHARGE
. . . 24-35
CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING, RADIATOR
.....7-61
CARDAN UNIVERSAL JOINTS -
ASSEMBLY, SINGLE
.....................3-9
DRINDEX 5
Description Group-Page Description Group-Page Description Group-Page

ERASING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-12
ETC INDICATOR - DESCRIPTION.........8J-24
ETC INDICATOR - OPERATION..........8J-25
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM..........24-35,24-51
EVAP SYSTEM - DESCRIPTION..........25-10
EVAP SYSTEM - TORQUE..............25-12
EVAPORATOR - DESCRIPTION, A/C.......24-47
EVAPORATOR - INSTALLATION, A/C......24-47
EVAPORATOR - OPERATION, A/C........24-47
EVAPORATOR - REMOVAL, A/C..........24-47
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-12
EVAP/PURGE SOLENOID - INSTALLATION . 25-13
EVAP/PURGE SOLENOID - OPERATION....25-12
EVAP/PURGE SOLENOID - REMOVAL.....25-13
EXCEPT 4X4 HD - INSTALLATION, ALL
LD & HD ...........................19-15
EXCEPT 4X4 HD - REMOVAL, ALL LD &
HD................................19-14
EXCEPT DIESEL - INSTALLATION........14-22
EXCEPT DIESEL - REMOVAL............14-20
EXCEPT HYDROBOOST - INSTALLATION,
ALL ................................5-22
EXCEPT HYDROBOOST - REMOVAL, ALL . . . 5-21
EXCEPT V-10 OR DIESEL ENGINE -
INSTALLATION......................8R-17
EXCEPT V-10 OR DIESEL ENGINE -
REMOVAL............................8R-16
EXHAUST MANIFOLD - CLEANING . . 9-161,9-220,
9-277,9-347,9-404
EXHAUST MANIFOLD - DESCRIPTION....9-159,
9-220,9-277,9-403,9-73
EXHAUST MANIFOLD - INSPECTION.....9-161,
9-220,9-277,9-347,9-404
EXHAUST MANIFOLD - INSTALLATION . . . 9-162,
9-220,9-277,9-347,9-404,9-74
EXHAUST MANIFOLD - OPERATION . 9-220,9-277,
9-403
EXHAUST MANIFOLD - REMOVAL . . 9-159,9-220,
9-277,9-347,9-404,9-73
EXHAUST PIPE - INSPECTION...........11-7
EXHAUST PIPE - INSTALLATION..........11-7
EXHAUST PIPE - REMOVAL.............11-7
EXTENSION HOUSING BUSHING -
INSTALLATION......................21-200
EXTENSION HOUSING BUSHING -
REMOVAL.........................21-200
EXTENSION HOUSING BUSHING AND
SEAL - INSTALLATION..........21-616,21-682
EXTENSION HOUSING BUSHING AND
SEAL - REMOVAL.............21-616,21-682
EXTENSION HOUSING SEAL -
INSTALLATION.....21-127,21-200,21-380,21-83
EXTENSION HOUSING SEAL - REMOVAL . 21-127,
21-200,21-380,21-83
EXTENSION HOUSING SEAL AND DUST
BOOT - INSTALLATION.........21-652,21-716
EXTENSION HOUSING SEAL AND DUST
BOOT - REMOVAL.............21-652,21-716
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING.....................8L-3
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR HANDLE - INSTALLATION.....23-20,
23-30
EXTERIOR HANDLE - REMOVAL
....23-20,23-30
EXTERIOR LAMPS, SPECIFICATIONS
......8L-7
EXTERIOR NAME PLATES -
INSTALLATION
.......................23-38
EXTERIOR NAME PLATES - REMOVAL
....23-38
FAILURE - DIAGNOSIS AND TESTING,
CYLINDER HEAD GASKET
....9-194,9-243,9-370
FAN - 5.9L DIESEL - CLEANING,
RADIATOR
...........................7-41
FAN - 5.9L DIESEL - INSPECTION,
RADIATOR
...........................7-41
FAN - 5.9L DIESEL - INSTALLATION,
RADIATOR
...........................7-41
FAN - 5.9L DIESEL - REMOVAL,
RADIATOR
...........................7-41
FAN - CLEANING, RADIATOR
............7-40
FAN - INSPECTION, RADIATOR
...........7-40
FAN - INSTALLATION, RADIATOR
.........7-40
FAN - REMOVAL, RADIATOR
.............7-39FAN DRIVE - DIAGNOSIS AND TESTING,
ELECTRONICLY CONTOLLED VISCOUS.....7-56
FAN DRIVE - DIAGNOSIS AND TESTING,
VISCOUS............................7-54
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - DESCRIPTION................7-55
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - OPERATION..................7-55
FAN DRIVE VISCOUS CLUTCH -
DESCRIPTION........................7-54
FAN DRIVE VISCOUS CLUTCH -
OPERATION..........................7-54
FAN (GAS ENGINE ONLY - 3.7, 4.7 &
5.7L) - INSTALLATION, CONDENSER.....24-43
FAN (GAS ENGINE ONLY - 3.7, 4.7 &
5.7L) - REMOVAL, CONDENSER.........24-43
FASCIA - INSTALLATION, FRONT.........13-3
FASCIA - REMOVAL, FRONT.............13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-6
FASTENER USAGE - DESCRIPTION......Intro.-9
FENDER - INSTALLATION, FRONT........23-39
FENDER - INSTALLATION, REAR.........23-44
FENDER - REMOVAL, FRONT...........23-39
FENDER - REMOVAL, REAR............23-44
FENDER RAIL REPAIR - STANDARD
PROCEDURE, HYDROFORM............13-12
FILL - STANDARD PROCEDURE,
TRANSMISSION.........21-203,21-383,21-544
FILL DOOR - INSTALLATION, FUEL.......23-39
FILL DOOR - REMOVAL, FUEL............23-39
FILLER CAP - DESCRIPTION, FUEL.......25-13
FILLER CAP - OPERATION, FUEL........25-13
FILTER - INSTALLATION, INLET..........14-23
FILTER - INSTALLATION, OIL . 9-153,9-217,9-270,
9-342,9-397,9-70
FILTER - REMOVAL, INLET.............14-23
FILTER - REMOVAL, OIL.....9-152,9-216,9-270,
9-342,9-397,9-69
FILTER - STANDARD PROCEDURES,
WATER DRAINING AT FUEL............14-57
FILTER / WATER SEPARATOR -
DESCRIPTION, FUEL..................14-61
FILTER / WATER SEPARATOR -
INSTALLATION, FUEL.................14-62
FILTER / WATER SEPARATOR -
OPERATION, FUEL....................14-61
FILTER / WATER SEPARATOR -
REMOVAL, FUEL.....................14-61
FILTER REPLACEMENT - STANDARD
PROCEDURE, FLUID.....21-203,21-383,21-542
FILTER/PRESSURE REGULATOR -
DESCRIPTION, FUEL...................14-6
FILTER/PRESSURE REGULATOR -
OPERATION, FUEL.....................14-6
FINESSE SANDING/BUFFING &
POLISHING - DESCRIPTION............23-75
FINISH - DESCRIPTION, BASECOAT/
CLEARCOAT.........................23-74
FIRING ORDER / CABLE ROUTING, 5.7L
V-8 ENGINE..........................8I-4
FIRING ORDER, 3.7L V-6 - ENGINE........8I-4
FIRING ORDER, 4.7L V-8 - ENGINE........8I-4
FIRING ORDER, 5.9L V-8 - ENGINE........8I-4
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-60
FITTING - DESCRIPTION, QUICK
CONNECT............................14-8
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING . 9-128,9-251,9-382
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING..........9-253
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING.....9-133,9-202
FITTING - STANDARD PROCEDURE,
PISTON.........9-137,9-205,9-260,9-389,9-50
FITTING - STANDARD PROCEDURE,
PISTON RING....9-140,9-207,9-262,9-333,9-52
FITTING CRANKSHAFT MAIN BEARINGS
- STANDARD PROCEDURE
.............9-383
FITTING PISTON RINGS - STANDARD
PROCEDURE
........................9-390
FITTING, STANDARD PROCEDURE -
CONNECTING ROD BEARING
............9-48
FITTING, STANDARD PROCEDURE -
MAIN BEARING
.......................9-43
FITTINGS - STANDARD PROCEDURE,
QUICK-CONNECT
......................14-8FIXED ORIFICE TUBE - DIAGNOSIS AND
TESTING...........................24-48
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-27
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-27
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-7
FLARING - STANDARD PROCEDURE, ISO....5-7
FLEX PLATE - INSTALLATION . . 9-137,9-205,9-47
FLEX PLATE - REMOVAL......9-137,9-205,9-47
FLOOR - DEFROST DOOR -
INSTALLATION.......................24-30
FLOOR - DEFROST DOOR - REMOVAL....24-30
FLOOR - DEFROST DOOR ACTUATOR -
INSTALLATION.......................24-20
FLOOR - DEFROST DOOR ACTUATOR -
REMOVAL..........................24-19
FLOOR - INSTALLATION, LOAD..........23-73
FLOOR - REMOVAL, LOAD.............23-73
FLOOR CONSOLE - INSTALLATION.......23-68
FLOOR CONSOLE - REMOVAL...........23-68
FLOOR DISTRIBUTION DUCTS -
INSTALLATION.......................24-27
FLOOR DISTRIBUTION DUCTS -
REMOVAL..........................24-27
FLOOR MATS - INSTALLATION, CARPETS . 23-66
FLOOR MATS - REMOVAL, CARPETS.....23-66
FLOOR SHIFT BOOT - INSTALLATION,
4WD ..............................23-64
FLOOR SHIFT BOOT - REMOVAL, 4WD.....23-63
FLOOR SUPPORT CYLINDER -
INSTALLATION, LOAD.................23-73
FLOOR SUPPORT CYLINDER -
REMOVAL, LOAD.....................23-73
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-2
FLOW - 5.9L ENGINE - DESCRIPTION,
COOLING SYSTEM.....................7-1
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..............7-57,7-59
FLOW 3.7L/4.7L ENGINE - DESCRIPTION,
COOLING SYSTEM.....................7-1
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION................19-42
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-4
FLUID - DESCRIPTION, POWER
STEERING............................0-3
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT......21-201,21-381,21-541
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE . . 21-203,21-383,21-542
FLUID CAPACITIES, SPECIFICATIONS.......0-5
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING..........21-201,21-381,21-541
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-18
FLUID COOLER - INSTALLATION.........19-42
FLUID COOLER - REMOVAL............19-42
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE.....21-617,21-652,21-682,21-716
FLUID INDICATOR - DESCRIPTION,
WASHER...........................8J-42
FLUID INDICATOR - OPERATION,
WASHER...........................8J-42
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING . . . 21-143,21-324,21-495
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT.....21-201,
21-381,21-541
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE..............................5-18
FLUID LEVEL CHECK - STANDARD
PROCEDURE...........21-201,21-381,21-542
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING........19-42
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER
............................8R-9
FLUID LEVEL SWITCH - INSTALLATION,
WASHER
...........................8R-11
FLUID LEVEL SWITCH - OPERATION,
WASHER
............................8R-9
FLUID LEVEL SWITCH - REMOVAL,
WASHER
...........................8R-10
FLUID RESERVOIR - INSTALLATION
.......5-19
DRINDEX 13
Description Group-Page Description Group-Page Description Group-Page

MOLDING - INSTALLATION, REAR DOOR
INNER BELT.........................23-94
MOLDING - INSTALLATION, REAR DOOR
OUTER BELT........................23-94
MOLDING - REMOVAL, FRONT DOOR
INNER BELT.........................23-93
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT........................23-93
MOLDING - REMOVAL, REAR DOOR
INNER BELT.........................23-94
MOLDING - REMOVAL, REAR DOOR
OUTER BELT........................23-94
MOLDINGS - INSTALLATION, BODY SIDE . . 23-36
MOLDINGS - REMOVAL, BODY SIDE.....23-36
MONITORED SYSTEMS - DESCRIPTION....25-1
MONITORS - DESCRIPTION,
COMPONENT.........................25-4
MOTOR - DESCRIPTION, ADJUSTABLE
PEDAL..............................5-24
MOTOR - DESCRIPTION, BLOWER.......24-25
MOTOR - DESCRIPTION, DOOR LOCK.....8N-5
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-33
MOTOR - DESCRIPTION, LUMBAR.......8N-19
MOTOR - DESCRIPTION, SHIFT . . 21-686,21-720
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-26
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK.........................8N-5
MOTOR - DIAGNOSIS AND TESTING,
LUMBAR...........................8N-20
MOTOR - DIAGNOSIS AND TESTING,
STARTER ...........................8F-34
MOTOR - INSTALLATION, ADJUSTABLE
PEDAL..............................5-24
MOTOR - INSTALLATION, BLOWER......24-26
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-35
MOTOR - INSTALLATION, SHIFT . . 21-686,21-720
MOTOR - INSTALLATION, STARTER......8F-37
MOTOR - OPERATION, BLOWER.........24-25
MOTOR - OPERATION, DOOR LOCK.......8N-5
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-33
MOTOR - OPERATION, LUMBAR........8N-20
MOTOR - OPERATION, SHIFT....21-686,21-720
MOTOR - REMOVAL, ADJUSTABLE
PEDAL..............................5-24
MOTOR - REMOVAL, BLOWER..........24-26
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-34
MOTOR - REMOVAL, SHIFT.....21-686,21-720
MOTOR - REMOVAL, STARTER..........8F-34
MOTOR - REMOVAL, WINDOW..........8N-22
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-38
MOTOR RELAY - INSTALLATION,
STARTER ...........................8F-39
MOTOR RELAY - OPERATION, STARTER . . . 8F-38
MOTOR RELAY - REMOVAL, STARTER....8F-39
MOTOR RESISTOR - DIAGNOSIS AND
TESTING, BLOWER...................24-18
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-17
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER
..............24-18
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER
...........................24-17
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER
...........................24-18
MOTOR SWITCH - DESCRIPTION,
BLOWER
...........................24-18
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER
...................24-18
MOTOR SWITCH - INSTALLATION,
BLOWER
...........................24-19
MOTOR SWITCH - OPERATION, BLOWER
. . 24-18
MOTOR SWITCH - REMOVAL, BLOWER
. . . 24-19
MOUNT - INSTALLATION, DISC BRAKE
CALIPER ADAPTER
....................5-17
MOUNT - INSTALLATION, FRONT
. . . 9-144,9-211,
9-265,9-335,9-392,9-58
MOUNT - INSTALLATION, REAR
....9-147,9-213,
9-267,9-337,9-393,9-60
MOUNT - REMOVAL, FRONT
. 9-144,9-211,9-264,
9-335,9-392,9-57
MOUNT - REMOVAL, REAR
. . 9-147,9-213,9-266,
9-337,9-393,9-60MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH.......................8L-10
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH.......................8L-10
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-10
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-10
MOUNTING - STANDARD PROCEDURE,
MATCH .............................22-3
MUFFLER - 5.9L DIESEL - INSTALLATION . . 11-9
MUFFLER - 5.9L DIESEL - REMOVAL......11-9
MUFFLER - INSTALLATION..............11-8
MUFFLER - REMOVAL..................11-8
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-18
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-19
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - INSTALLATION,
EXTERIOR..........................23-38
NAME PLATES - REMOVAL, EXTERIOR....23-38
NATURAL VAC LEAK DETECTION ASSY -
DESCRIPTION.......................25-23
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-24
NATURAL VAC LEAK DETECTION ASSY -
OPERATION.........................25-23
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-24
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER...............7-61
NEW MODULE / SWITCH OPERATING
MODES, STANDARD PROCEDURE -
CONFIGURING A......................8Q-3
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-12
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - REMOVAL,
AUTOMATIC DAY.....................8N-13
NOISE - DIAGNOSIS AND TESTING, A/C
COMPRESSOR.......................24-36
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-7
NOISE SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO..................8A-8
NOISE SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO................8A-10
NOISE SUPPRESSION GROUND STRAP -
OPERATION, RADIO...................8A-8
NOISE SUPPRESSION GROUND STRAP -
REMOVAL, RADIO.....................8A-9
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NON-MONITORED CIRCUITS -
OPERATION..........................25-8
NOZZLE - DESCRIPTION, WASHER......8R-12
NOZZLE - INSTALLATION, WASHER......8R-12
NOZZLE - OPERATION, WASHER........8R-12
NOZZLE - REMOVAL, WASHER..........8R-12
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-2
NV241 GENII - ASSEMBLY, TRANSFER
CASE.............................21-604
NV241 GENII - CLEANING, TRANSFER
CASE.............................21-602
NV241 GENII - DESCRIPTION, TRANSFER
CASE................................0-4
NV241 GENII - DESCRIPTION, TRANSFER
CASE.............................21-591
NV241 GENII - DIAGNOSIS AND
TESTING, TRANSFER CASE............21-592
NV241 GENII - DISASSEMBLY,
TRANSFER CASE
....................21-593
NV241 GENII - INSPECTION, TRANSFER
CASE
.............................21-602
NV241 GENII - INSTALLATION,
TRANSFER CASE
....................21-614
NV241 GENII - OPERATION, TRANSFER
CASE
.............................21-591
NV241 GENII - REMOVAL, TRANSFER
CASE
.............................21-593NV241 GENII - TRANSFER CASE........21-614
NV241/NV243 - TRANSFER CASE . 21-615,21-680
NV243 - ASSEMBLY, TRANSFER CASE . . . 21-670
NV243 - CLEANING, TRANSFER CASE . . . 21-668
NV243 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV243 - DESCRIPTION, TRANSFER CASE . 21-658
NV243 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-659
NV243 - DISASSEMBLY, TRANSFER
CASE.............................21-660
NV243 - INSPECTION, TRANSFER CASE . . 21-668
NV243 - INSTALLATION, TRANSFER
CASE.............................21-679
NV243 - OPERATION, TRANSFER CASE . . 21-659
NV243 - REMOVAL, TRANSFER CASE....21-660
NV243 - TRANSFER CASE.............21-680
NV271 - ASSEMBLY, TRANSFER CASE . . . 21-637
NV271 - CLEANING, TRANSFER CASE . . . 21-635
NV271 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV271 - DESCRIPTION, TRANSFER CASE . 21-623
NV271 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-624
NV271 - DISASSEMBLY, TRANSFER
CASE.............................21-625
NV271 - INSPECTION, TRANSFER CASE . . 21-635
NV271 - INSTALLATION, TRANSFER
CASE.............................21-649
NV271 - OPERATION, TRANSFER CASE . . 21-623
NV271 - REMOVAL, TRANSFER CASE....21-625
NV271 - TRANSFER CASE.............21-649
NV271/NV273, SPECIAL TOOLS -
TRANSFER CASE..............21-650,21-714
NV273 - ASSEMBLY, TRANSFER CASE . . . 21-701
NV273 - CLEANING, TRANSFER CASE . . . 21-698
NV273 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV273 - DESCRIPTION, TRANSFER CASE . 21-687
NV273 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-688
NV273 - DISASSEMBLY, TRANSFER
CASE.............................21-689
NV273 - INSPECTION, TRANSFER CASE . . 21-699
NV273 - INSTALLATION, TRANSFER
CASE.............................21-713
NV273 - OPERATION, TRANSFER CASE . . 21-688
NV273 - REMOVAL, TRANSFER CASE....21-689
NV273 - TRANSFER CASE.............21-713
NV3500 - ASSEMBLY, MANUAL
TRANSMISSION......................21-17
NV3500 - CLEANING, MANUAL
TRANSMISSION......................21-15
NV3500 - DESCRIPTION, MANUAL
TRANSMISSION.......................21-1
NV3500 - DIAGNOSIS AND TESTING,
MANUAL TRANSMISSION...............21-3
NV3500 - DISASSEMBLY, MANUAL
TRANSMISSION.......................21-4
NV3500 - INSPECTION, MANUAL
TRANSMISSION......................21-15
NV3500 - INSTALLATION, MANUAL
TRANSMISSION......................21-38
NV3500 - OPERATION, MANUAL
TRANSMISSION.......................21-1
NV3500 - REMOVAL, MANUAL
TRANSMISSION.......................21-3
NV3500 - SPECIAL TOOLS, MANUAL
TRANSMISSION......................21-40
NV3500 - SPECIFICATIONS, MANUAL
TRANSMISSION......................21-39
NV4500 - ASSEMBLY, MANUAL
TRANSMISSION......................21-61
NV4500 - CLEANING, MANUAL
TRANSMISSION......................21-60
NV4500 - DESCRIPTION, MANUAL
TRANSMISSION......................21-42
NV4500 - DIAGNOSIS AND TESTING,
MANUAL TRANSMISSION..............21-43
NV4500 - DISASSEMBLY, MANUAL
TRANSMISSION......................21-44
NV4500 - INSPECTION, MANUAL
TRANSMISSION
......................21-60
NV4500 - INSTALLATION, MANUAL
TRANSMISSION
......................21-77
NV4500 - OPERATION, MANUAL
TRANSMISSION
......................21-42
NV4500 - REMOVAL, MANUAL
TRANSMISSION
......................21-43
NV4500 - SPECIAL TOOLS, MANUAL
TRANSMISSION
......................21-79
22 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

PLANETARY GEARTRAIN/OUTPUT SHAFT
- INSPECTION................21-245,21-422
PLANETARY GEARTRAIN/OUTPUT SHAFT
- OPERATION.................21-243,21-420
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE - DESCRIPTION, BODY CODE....Intro.-4
PLATE - DESCRIPTION, ENGINE DATA....9-297
PLATE - INSTALLATION, FLEX . . 9-137,9-205,9-47
PLATE - INSTALLATION, FRONT SKID.....13-24
PLATE - INSTALLATION, SUPPORT........5-29
PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-26
PLATE - REMOVAL, FLEX.....9-137,9-205,9-47
PLATE - REMOVAL, FRONT SKID........13-24
PLATE - REMOVAL, SUPPORT...........5-29
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-26
PLATE LAMP - INSTALLATION, LICENSE . . 8L-16
PLATE LAMP - REMOVAL, LICENSE......8L-16
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-16
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-16
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-38
PLATES - REMOVAL, EXTERIOR NAME....23-38
PLUG - DESCRIPTION, SPARK...........8I-27
PLUG - INSTALLATION, CAMSHAFT
CORE HOLE.........................9-201
PLUG - REMOVAL, CAMSHAFT CORE
HOLE..............................9-200
PLUG - REMOVAL, SPARK..............8I-30
PLUG CABLE - DESCRIPTION, SPARK.....8I-33
PLUG CABLE - INSTALLATION, SPARK....8I-35
PLUG CABLE - OPERATION, SPARK.......8I-33
PLUG CABLE - REMOVAL, SPARK........8I-34
PLUG CABLE ORDER, 8.0L V-10 ENGINE
- SPARK .............................8I-5
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK...............8I-5
PLUG CABLES - DIAGNOSIS AND
TESTING, SPARK.....................8I-33
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK.....................8I-27
PLUGS - INSTALLATION, CORE..........9-130
PLUGS - REMOVAL, CORE.............9-129
PLUGS, SPECIFICATIONS - SPARK........8I-5
PLUMBING - CLEANING, CHARGE AIR
COOLER............................11-16
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER........................11-15
PLUMBING - INSPECTION, CHARGE AIR
COOLER............................11-16
PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-16
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-15
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-15
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISHING - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-75
PORT - DESCRIPTION, REFRIGERANT
SYSTEM SERVICE.....................24-1
PORT - OPERATION, REFRIGERANT
SYSTEM SERVICE.....................24-2
POSITION SENSOR - DESCRIPTION.....21-618,
21-654
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-25
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-82
POSITION SENSOR - DESCRIPTION,
CAMSHAFT...........................8I-8
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT..................14-26,14-83
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-52
POSITION SENSOR - INSTALLATION
....21-619,
21-654
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL
.................14-25
POSITION SENSOR - INSTALLATION,
CAMSHAFT
.........................14-83
POSITION SENSOR - INSTALLATION,
CAMSHAFT
..........................8I-14
POSITION SENSOR - INSTALLATION,
CRANKSHAFT
..................14-30,14-84POSITION SENSOR - INSTALLATION,
THROTTLE..........................14-54
POSITION SENSOR - OPERATION . 21-619,21-654
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL.................14-25
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-82
POSITION SENSOR - OPERATION,
CAMSHAFT...........................8I-8
POSITION SENSOR - OPERATION,
CRANKSHAFT..................14-26,14-83
POSITION SENSOR - OPERATION,
THROTTLE..........................14-52
POSITION SENSOR - REMOVAL . . 21-619,21-654
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL.................14-25
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-83
POSITION SENSOR - REMOVAL,
CAMSHAFT..........................8I-11
POSITION SENSOR - REMOVAL,
CRANKSHAFT..................14-29,14-84
POSITION SENSOR - REMOVAL,
THROTTLE..........................14-53
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-14
POSITION SWITCH - DIAGNOSIS AND
TESTING, CLUTCH PEDAL...............6-14
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-14
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-9
POWER - INSTALLATION, WINDOW
REGULATOR...................23-25,23-34
POWER - REMOVAL, WINDOW
REGULATOR...................23-25,23-34
POWER BRAKE BOOSTER -
DESCRIPTION........................5-25
POWER BRAKE BOOSTER -
INSTALLATION........................5-25
POWER BRAKE BOOSTER - OPERATION . . . 5-25
POWER BRAKE BOOSTER - REMOVAL.....5-25
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-10
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-4
POWER LOCK SWITCH - INSTALLATION . . . 8N-4
POWER LOCK SWITCH - REMOVAL.......8N-4
POWER LOCKS - DESCRIPTION..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING............................8N-3
POWER LOCKS - OPERATION............8N-2
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING.......................8N-13
POWER MIRROR SWITCH - REMOVAL
. . . 8N-13
POWER MIRRORS - DESCRIPTION
......8N-11
POWER MIRRORS - DIAGNOSIS AND
TESTING
...........................8N-11
POWER MIRRORS - OPERATION
........8N-11
POWER MODULE - DESCRIPTION,
INTEGRATED
......................8W-97-3
POWER MODULE - INSTALLATION,
INTEGRATED
......................8W-97-4
POWER MODULE - OPERATION,
INTEGRATED
......................8W-97-3
POWER MODULE - REMOVAL,
INTEGRATED
......................8W-97-3
POWER OUTLET - DESCRIPTION
......8W-97-7
POWER OUTLET - DIAGNOSIS AND
TESTING
.........................8W-97-7
POWER OUTLET - INSTALLATION
.....8W-97-7
POWER OUTLET - OPERATION
........8W-97-7
POWER OUTLET - REMOVAL
.........8W-97-7
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING
.......................8N-14
POWER SEAT TRACK - DESCRIPTION
....8N-18
POWER SEAT TRACK - DIAGNOSIS AND
TESTING
...........................8N-18
POWER SEAT TRACK - INSTALLATION
....8N-19
POWER SEAT TRACK - OPERATION
......8N-18
POWER SEAT TRACK - REMOVAL
.......8N-19
POWER SEATS - DESCRIPTION
.........8N-14
POWER SEATS - OPERATION
...........8N-14POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING FLUID -
DESCRIPTION.........................0-3
POWER STEERING FLUID LEVEL
CHECKING - STANDARD PROCEDURE....19-42
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-22
POWER STEERING GEAR,
SPECIFICATIONS.....................19-21
POWER STEERING PRESSURE SWITCH -
DESCRIPTION.......................19-45
POWER STEERING PRESSURE SWITCH -
OPERATION.........................19-45
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-39
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING.....19-39
POWER WINDOWS - DESCRIPTION......8N-21
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-21
POWER WINDOWS - OPERATION........8N-21
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING...............2-2
PRECAUTIONS - CAUTION,
REFRIGERANT HOSES/LINES/TUBES......24-33
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY.....................23-1
PRECAUTIONS, STANDARD PROCEDURE
- SAFETY............................8L-7
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY.................23-88
PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER
CUSTOMER..........................8N-9
PRELIMINARY - DIAGNOSIS AND
TESTING..............21-139,21-320,21-491
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING........................7-10
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE............................9-10
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.......9-150,9-214,9-64
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION . . . 9-182,9-231,9-359,
9-8,9-92
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL...............9-269,9-338,9-396
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW...............19-4
PRESSURE - DIAGNOSIS AND TESTING,
TURBOCHARGER BOOST...............11-10
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-60
PRESSURE CAP - OPERATION,
RADIATOR...........................7-61
PRESSURE, DIESEL - FUEL SYSTEM
.....14-60
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE
...................22-6
PRESSURE GAUGE - DESCRIPTION, OIL
. . 8J-32
PRESSURE GAUGE - OPERATION, OIL
....8J-32
PRESSURE GAUGES - DIAGNOSIS AND
TESTING
............................22-7
PRESSURE HOSE - INSTALLATION
. . 19-43,19-44
PRESSURE HOSE - REMOVAL
.....19-43,19-44
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION
. 9-182,9-231,
9-359,9-8,9-92
PRESSURE LIMITING VALVE -
DESCRIPTION, FUEL
..................14-72
PRESSURE LIMITING VALVE -
INSTALLATION, FUEL
.................14-73
PRESSURE LIMITING VALVE -
OPERATION, FUEL
....................14-72
PRESSURE LIMITING VALVE - REMOVAL,
FUEL
..............................14-72
PRESSURE (LP) SENSOR -
DESCRIPTION, LINE
.................21-559
DRINDEX 25
Description Group-Page Description Group-Page Description Group-Page

PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-560
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-559
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-559
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-2
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-343
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-35
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-343
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-343
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-36
PRESSURE RELIEF VALVE - REMOVAL,
OIL................................9-343
PRESSURE SENSOR - DESCRIPTION,
FUEL..............................14-72
PRESSURE SENSOR - INSTALLATION,
FUEL..............................14-72
PRESSURE SENSOR - OPERATION, FUEL . . 14-72
PRESSURE SENSOR - REMOVAL, FUEL . . . 14-72
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-66
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL...............9-343,9-67
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-66
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL..................9-343,9-67
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-3
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-45
PRESSURE SWITCH - OPERATION,
POWER STEERING...................19-45
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC....21-140,21-321,21-493
PRESSURE TRANSDUCER -
DESCRIPTION, A/C...................24-15
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-15
PRESSURE TRANSDUCER -
INSTALLATION, A/C...................24-16
PRESSURE TRANSDUCER - OPERATION,
A/C................................24-15
PRESSURE TRANSDUCER - REMOVAL,
A/C................................24-16
PRESSURES - DESCRIPTION, TIRE
INFLATION...........................22-6
PRIMING - STANDARD PROCEDURE,
FUEL SYSTEM.......................14-59
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER.......8N-10
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER................8M-8
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM...............8E-14
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY
IMMOBILIZER SYSTEM TRANSPONDER....8Q-4
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - INSTALLATION,
FRONT...............................3-7
PROPELLER SHAFT - INSTALLATION,
REAR................................3-8
PROPELLER SHAFT - REMOVAL, FRONT....3-6
PROPELLER SHAFT - REMOVAL, REAR.....3-7
PROPELLER SHAFT - SPECIAL TOOLS......3-6
PROPELLER SHAFT - SPECIFICATIONS......3-6
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE..........5-43
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-43
PULLEY - INSTALLATION..............19-46
PULLEY - REMOVAL
..................19-45
PUMP - 5.7L - INSTALLATION, WATER
.....7-71
PUMP - 5.7L - REMOVAL, WATER
........7-70
PUMP - 5.9L - CLEANING, WATER
........7-64
PUMP - 5.9L - DESCRIPTION, WATER
.....7-62PUMP - 5.9L - INSPECTION, WATER......7-64
PUMP - 5.9L - INSTALLATION, WATER.....7-64
PUMP - 5.9L - OPERATION, WATER.......7-62
PUMP - 5.9L - REMOVAL, WATER........7-63
PUMP - 5.9L DIESEL - CLEANING,
WATER .............................7-67
PUMP - 5.9L DIESEL - DESCRIPTION,
WATER .............................7-67
PUMP - 5.9L DIESEL - INSPECTION,
WATER .............................7-68
PUMP - 5.9L DIESEL - INSTALLATION,
WATER .............................7-68
PUMP - 5.9L DIESEL - OPERATION,
WATER .............................7-67
PUMP - 5.9L DIESEL - REMOVAL,
WATER .............................7-67
PUMP - ASSEMBLY, OIL......9-156,9-274,9-68
PUMP - ASSEMBLY, OIL . . 21-215,21-393,21-566
PUMP - CLEANING, OIL.....9-155,9-218,9-344,
9-398
PUMP - CLEANING, OIL . . 21-214,21-393,21-566
PUMP - DESCRIPTION................19-38
PUMP - DESCRIPTION, FUEL...........14-12
PUMP - DESCRIPTION, FUEL INJECTION . . 14-64
PUMP - DESCRIPTION, FUEL TRANSFER . . 14-75
PUMP - DESCRIPTION, LEAK DETECTION . 25-13
PUMP - DESCRIPTION, OIL.....21-212,21-392,
21-562
PUMP - DESCRIPTION, WATER..........7-64
PUMP - DIAGNOSIS AND TESTING,
WATER .........................7-62,7-67
PUMP - DISASSEMBLY, OIL . . . 9-155,9-272,9-67
PUMP - DISASSEMBLY, OIL.....21-212,21-393,
21-564
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-39
PUMP - INSPECTION, OIL . . . 9-155,9-218,9-272,
9-344,9-399,9-67
PUMP - INSPECTION, OIL . 21-214,21-393,21-566
PUMP - INSTALLATION, FUEL INJECTION . 14-67
PUMP - INSTALLATION, FUEL TRANSFER . 14-76
PUMP - INSTALLATION, LEAK
DETECTION.........................25-16
PUMP - INSTALLATION, OIL . 9-157,9-219,9-274,
9-344,9-400,9-68
PUMP - OPERATION..................19-38
PUMP - OPERATION, FUEL.............14-12
PUMP - OPERATION, FUEL INJECTION....14-64
PUMP - OPERATION, FUEL TRANSFER....14-76
PUMP - OPERATION, LEAK DETECTION . . . 25-14
PUMP - OPERATION, OIL . 21-212,21-392,21-562
PUMP - OPERATION, WATER............7-64
PUMP - REMOVAL, FUEL INJECTION.....14-65
PUMP - REMOVAL, FUEL TRANSFER.....14-76
PUMP - REMOVAL, LEAK DETECTION....25-16
PUMP - REMOVAL, OIL.....9-154,9-218,9-272,
9-343,9-398,9-67
PUMP BYPASS - DESCRIPTION, WATER . . . 7-64
PUMP BYPASS - OPERATION, WATER.....7-65
PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION,
WATER .............................7-70
PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL, WATER......7-68
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER .............................7-70
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER......7-69
PUMP FRONT SEAL - INSTALLATION,
OIL
...............................21-567
PUMP FRONT SEAL - REMOVAL, OIL
....21-567
PUMP LEAKAGE - DIAGNOSIS AND
TESTING
...........................19-39
PUMP MODULE - DESCRIPTION, FUEL
....14-12
PUMP MODULE - INSTALLATION, FUEL
. . . 14-13
PUMP MODULE - OPERATION, FUEL
.....14-12
PUMP MODULE - REMOVAL, FUEL
.......14-12
PUMP RELAY - DESCRIPTION, FUEL
.....14-33
PUMP RELAY - INSTALLATION, FUEL
.....14-33
PUMP RELAY - OPERATION, FUEL
.......14-33
PUMP RELAY - REMOVAL, FUEL
........14-33
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL
...............8I-7
PUMP TIMING - DIAGNOSIS AND
TESTING, FUEL INJECTION
.............14-65PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-563
PUMP/MOTOR - DESCRIPTION, WASHER . 8R-13
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-14
PUMP/MOTOR - OPERATION, WASHER . . . 8R-13
PUMP/MOTOR - REMOVAL, WASHER....8R-14
PUSHRODS - CLEANING...............9-301
PUSHRODS - INSPECTION.............9-302
QUAD CAB - INSTALLATION............8O-32
QUAD CAB - REMOVAL................8O-29
QUICK CONNECT FITTING -
DESCRIPTION........................14-8
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-21
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE.........................14-8
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - 5.9L DIESEL - CLEANING.....7-60
RADIATOR - 5.9L DIESEL -
DESCRIPTION........................7-59
RADIATOR - 5.9L DIESEL - INSPECTION . . . 7-60
RADIATOR - 5.9L DIESEL -
INSTALLATION........................7-60
RADIATOR - 5.9L DIESEL - OPERATION....7-59
RADIATOR - 5.9L DIESEL - REMOVAL.....7-59
RADIATOR - CLEANING.................7-58
RADIATOR - DESCRIPTION..............7-56
RADIATOR - INSPECTION.................7-58
RADIATOR - INSTALLATION.............7-58
RADIATOR - OPERATION................7-56
RADIATOR - REMOVAL.................7-57
RADIATOR CAP - DIAGNOSIS AND
TESTING............................7-61
RADIATOR CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-61
RADIATOR COOLANT FLOW -
DIAGNOSIS AND TESTING..........7-57,7-59
RADIATOR CROSSMEMBER -
INSTALLATION, UPPER................23-42
RADIATOR CROSSMEMBER - REMOVAL,
UPPER.............................23-42
RADIATOR FAN - 5.9L DIESEL -
CLEANING...........................7-41
RADIATOR FAN - 5.9L DIESEL -
INSPECTION.........................7-41
RADIATOR FAN - 5.9L DIESEL -
INSTALLATION........................7-41
RADIATOR FAN - 5.9L DIESEL -
REMOVAL...........................7-41
RADIATOR FAN - CLEANING.............7-40
RADIATOR FAN - INSPECTION...........7-40
RADIATOR FAN - INSTALLATION..........7-40
RADIATOR FAN - REMOVAL.............7-39
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-60
RADIATOR PRESSURE CAP - OPERATION . . 7-61
RADIO - DESCRIPTION.................8A-7
RADIO - INSTALLATION................8A-8
RADIO - OPERATION...................8A-7
RADIO - REMOVAL....................8A-7
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION.................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION...............8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION..................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL....................8A-9
RAIL - DESCRIPTION, FUEL
............14-13
RAIL - DESCRIPTION, FUEL INJECTOR
....14-89
RAIL - INSTALLATION, FUEL
............14-18
RAIL - INSTALLATION, FUEL INJECTOR
. . . 14-90
RAIL - OPERATION, FUEL
..............14-13
RAIL - OPERATION, FUEL INJECTOR
.....14-89
RAIL - REMOVAL, FUEL
...............14-13
RAIL - REMOVAL, FUEL INJECTOR
.......14-89
RAIL REPAIR - STANDARD PROCEDURE,
HYDROFORM FENDER
.................13-12
RAIL TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME
..............................13-4
RAIL WEATHERSTRIP - INSTALLATION,
DRIP
..............................23-91
RAIL WEATHERSTRIP - REMOVAL, DRIP
. . 23-91
RAIL WEATHERSTRIP RETAINER -
INSTALLATION, DRIP
.................23-92
26 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

RETURN - DESCRIPTION, SENSOR.......8E-10
RETURN HOSE - GEAR TO COOLER -
INSTALLATION..................19-43,19-44
RETURN HOSE - GEAR TO COOLER -
REMOVAL..........................19-43
RETURN HOSE - RESERVOIR TO
COOLER - INSTALLATION.........19-43,19-44
RETURN HOSE - RESERVOIR TO
COOLER - REMOVAL.............19-43,19-44
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE...............22-10
RFE TRANSMISSION, SPECIAL TOOLS . . . 21-535
RIGHT - DESCRIPTION, CAMSHAFT(S)....9-117
RIGHT - INSTALLATION.................2-34
RIGHT - INSTALLATION, CAMSHAFT(S) . . . 9-118
RIGHT - INSTALLATION, CYLINDER
HEAD...............................9-32
RIGHT - REMOVAL....................2-34
RIGHT - REMOVAL, CAMSHAFT(S).......9-117
RIGHT - REMOVAL, CYLINDER HEAD......9-32
RIGHT CYLINDER HEAD - INSTALLATION . . 9-111
RIGHT CYLINDER HEAD - REMOVAL.....9-108
RIGHT OUTBOARD - INSTALLATION,
CENTER ANCHOR....................8O-45
RIGHT OUTBOARD - REMOVAL, CENTER
ANCHOR...........................8O-43
RIGHT REAR CABLE - INSTALLATION......5-32
RIGHT REAR CABLE - REMOVAL.........5-31
RIGHT SIDE - INSTALLATION...........9-121
RIGHT SIDE - REMOVAL...............9-121
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE......3-123,3-150,3-96
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE................3-122,3-149,3-94
RING FITTING - STANDARD
PROCEDURE, PISTON . 9-140,9-207,9-262,9-333,
9-52
RINGS - STANDARD PROCEDURE,
FITTING PISTON.....................9-390
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-9
RKE TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE.........................8N-9
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE..............8N-10
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TESTING - DIAGNOSIS AND
TESTING..............21-139,21-320,21-491
ROCKER ARM / ADJUSTER ASSEMBLY -
DESCRIPTION.......................9-124
ROCKER ARM / ADJUSTER ASSEMBLY -
INSTALLATION..................9-124,9-249
ROCKER ARM / ADJUSTER ASSEMBLY -
REMOVAL.....................9-124,9-249
ROCKER ARM / ADJUSTER ASSY -
CLEANING..........................9-310
ROCKER ARM / ADJUSTER ASSY -
DESCRIPTION.......................9-310
ROCKER ARM / ADJUSTER ASSY -
INSPECTION........................9-311
ROCKER ARM / ADJUSTER ASSY -
INSTALLATION.............9-198,9-312,9-379
ROCKER ARM / ADJUSTER ASSY -
REMOVAL................9-198,9-310,9-379
ROCKER ARM - DESCRIPTION
.......9-30,9-36
ROCKER ARM - INSTALLATION
..........9-30
ROCKER ARM - REMOVAL
..........9-30,9-36
ROCKER HOUSING - INSTALLATION
......9-304
ROCKER HOUSING - REMOVAL
.........9-304
ROD - CLEANING, PISTON &
CONNECTING
........9-138,9-206,9-261,9-389
ROD - CLEANING, PISTON AND
CONNECTING
........................9-331
ROD - DESCRIPTION, PISTON &
CONNECTING
. . . 9-137,9-205,9-260,9-329,9-388,
9-47
ROD - INSPECTION, CONNECTING
.......9-332
ROD - INSPECTION, PISTON &
CONNECTING
........9-138,9-206,9-261,9-389
ROD - INSTALLATION, PISTON &
CONNECTING
........9-139,9-207,9-261,9-389
ROD - REMOVAL, PISTON &
CONNECTING
. . . 9-137,9-205,9-261,9-330,9-389
ROD BEARING AND CRANKSHAFT
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING
............9-321ROD BEARING FITTING - STANDARD
PROCEDURE, CONNECTING . . 9-128,9-251,9-382
ROD BEARING FITTING, STANDARD
PROCEDURE - CONNECTING.............9-48
ROD END - DIAGNOSIS AND TESTING,
OUTER TIE..........................19-31
ROD END - INSTALLATION, OUTER TIE . . . 19-32
ROD END - INSTALLATION, TIE.........19-37
ROD END - REMOVAL, OUTER TIE.......19-31
ROD END - REMOVAL, TIE.............19-36
ROTATION - STANDARD PROCEDURE,
TIRE................................22-2
ROTOR - 5.9L V-8 - DIAGNOSIS AND
TESTING, DISTRIBUTOR...............8I-19
ROUTING, 5.7L V-8 ENGINE - FIRING
ORDER / CABLE.......................8I-4
RUN CHANNEL - INSTALLATION, GLASS . . 23-21,
23-31
RUN CHANNEL - REMOVAL, GLASS . 23-21,23-30
RUN WEATHERSTRIP - INSTALLATION,
FRONT DOOR GLASS.................23-92
RUN WEATHERSTRIP - INSTALLATION,
REAR DOOR GLASS..................23-93
RUN WEATHERSTRIP - REMOVAL,
FRONT DOOR GLASS.................23-92
RUN WEATHERSTRIP - REMOVAL, REAR
DOOR GLASS.......................23-93
RUNOUT - DIAGNOSIS AND TESTING,
TIRE AND WHEEL.....................22-1
RWAL VALVE - DESCRIPTION............5-44
RWAL VALVE - INSTALLATION...........5-45
RWAL VALVE - OPERATION.............5-44
RWAL VALVE - REMOVAL...............5-45
SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE..............Intro.-1
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, STANDARD
PROCEDURE.........................8L-7
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD........................23-88
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE...............23-75
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-6
SCHEMATICS AND DIAGRAMS -
HYDRAULIC SCHEMATICS . 21-175,21-355,21-513
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - HYDRAULIC . 21-175,21-355,21-513
SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER NECK.........7-61
SEAL - FRONT - DESCRIPTION,
CRANKSHAFT OIL....................9-254
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL . 9-134,9-203,9-255,9-324,9-45
SEAL - FRONT - OPERATION,
CRANKSHAFT OIL....................9-254
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL . 9-134,9-203,9-254,9-323,9-44
SEAL - FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL.............9-384
SEAL - FRONT COVER INSTALLED -
REMOVAL, FRONT OIL................9-384
SEAL - FRONT COVER REMOVED -
INSTALLATION, FRONT OIL.............9-384
SEAL - FRONT COVER REMOVED -
REMOVAL, FRONT OIL................9-384
SEAL - INSTALLATION, ADAPTER
HOUSING...............21-127,21-539,21-83
SEAL - INSTALLATION, DOOR OPENING . . . 23-92
SEAL - INSTALLATION, EXTENSION
HOUSING.........21-127,21-200,21-380,21-83
SEAL - INSTALLATION, EXTENSION
HOUSING BUSHING............21-616,21-682
SEAL - INSTALLATION, FRONT OUTPUT
SHAFT..........21-618,21-653,21-683,21-717
SEAL - INSTALLATION, OIL PUMP
FRONT............................21-567
SEAL - INSTALLATION, PINION
....3-113,3-140,
3-35,3-60,3-85
SEAL - INSTALLATION, STEERING GEAR
INPUT SHAFT
.......................19-28
SEAL - INSTALLATION, VALVE STEM
.....9-378
SEAL - REAR - DESCRIPTION,
CRANKSHAFT OIL
....................9-255
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL
....9-136,9-204,9-256,9-325,
9-385,9-46SEAL - REAR - OPERATION,
CRANKSHAFT OIL....................9-255
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL .......9-135,9-204,9-255,9-325,9-385,9-45
SEAL - REMOVAL, ADAPTER HOUSING . . 21-127,
21-539,21-83
SEAL - REMOVAL, DOOR OPENING......23-92
SEAL - REMOVAL, EXTENSION
HOUSING.........21-127,21-200,21-380,21-83
SEAL - REMOVAL, EXTENSION HOUSING
BUSHING....................21-616,21-682
SEAL - REMOVAL, FRONT OUTPUT
SHAFT..........21-617,21-653,21-683,21-717
SEAL - REMOVAL, OIL PUMP FRONT....21-567
SEAL - REMOVAL, PINION....3-113,3-140,3-34,
3-60,3-85
SEAL - REMOVAL, STEERING GEAR
INPUT SHAFT.......................19-25
SEAL AND DUST BOOT - INSTALLATION,
EXTENSION HOUSING..........21-652,21-716
SEAL AND DUST BOOT - REMOVAL,
EXTENSION HOUSING..........21-652,21-716
SEAL AREA LEAKS - DIAGNOSIS AND
TESTING, REAR.............9-135,9-204,9-64
SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL.....9-205,9-326,9-386
SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR OIL.....9-204,9-326,9-386
SEALER LOCATIONS - SPECIFICATIONS . . 23-103
SEALERS - STANDARD PROCEDURE,
FORM-IN-PLACE GASKETS . . . 9-232,9-289,9-360,
9-9,9-93
SEALS - DESCRIPTION, VALVE GUIDE . . . 9-31,9-36
SEALS - DESCRIPTION, VALVE STEM....9-126,
9-198
SEALS - INSTALLATION, AXLE SHAFT . 3-33,3-58,
3-84
SEALS - REMOVAL, AXLE SHAFT . 3-33,3-58,3-84
SEALS - REMOVAL, VALVE SPRINGS.....9-308
SEALS - REMOVAL, VALVE STEM........9-377
SEAT - FRONT - INSTALLATION.........23-82
SEAT - FRONT - REMOVAL.............23-82
SEAT - INSTALLATION, CENTER.........23-77
SEAT - REAR - INSTALLATION..........23-84
SEAT - REAR - REMOVAL..............23-84
SEAT - REMOVAL, CENTER.............23-76
SEAT BACK - INSTALLATION, CENTER
ARMREST..........................23-78
SEAT BACK - REAR - INSTALLATION.....23-84
SEAT BACK - REAR - REMOVAL.........23-84
SEAT BACK - REMOVAL, CENTER
ARMREST..........................23-77
SEAT BACK CUSHION / COVER - FRONT
- INSTALLATION.....................23-83
SEAT BACK CUSHION / COVER - FRONT
- REMOVAL.........................23-83
SEAT BACK CUSHION / COVER - REAR -
INSTALLATION.......................23-85
SEAT BACK CUSHION / COVER - REAR -
REMOVAL..........................23-85
SEAT BACK HINGE - INSTALLATION,
CENTER............................23-80
SEAT BACK HINGE - REMOVAL, CENTER . . 23-79
SEAT BACK INERTIA HINGE COVER -
INSTALLATION, CENTER
...............23-78
SEAT BACK INERTIA HINGE COVER -
REMOVAL, CENTER
...................23-78
SEAT BACK LID - INSTALLATION,
CENTER
............................23-80
SEAT BACK LID - REMOVAL, CENTER
....23-80
SEAT BACK REAR - FOOTMANS LOOP
BRACKETS - INSTALLATION
............23-85
SEAT BACK REAR - FOOTMANS LOOP
BRACKETS - REMOVAL
................23-85
SEAT BELT - INSTALLATION, FRONT
CENTER
............................8O-27
SEAT BELT - REMOVAL, FRONT CENTER
. . 8O-26
SEAT BELT & RETRACTOR -
INSTALLATION, FRONT CENTER
.........8O-26
SEAT BELT & RETRACTOR -
INSTALLATION, REAR CENTER
..........8O-40
SEAT BELT & RETRACTOR -
INSTALLATION, REAR OUTBOARD
.......8O-42
SEAT BELT & RETRACTOR - REMOVAL,
FRONT CENTER
......................8O-25
SEAT BELT & RETRACTOR - REMOVAL,
REAR CENTER
.......................8O-39
DRINDEX 29
Description Group-Page Description Group-Page Description Group-Page