2003 DAEWOO MATIZ instrument panel

9E–2 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
CIGAR LIGHTER
The cigar lighter is located in the front portion of the in-
strument panel. To use the lighter, push it in completely.
When the lighter is hot, it will release itself from contact
with the heating element. The lighter and the heating
element can be damaged if the lighter is not allowed to
release itself fully from the heating element. Cigar lighter
is not equipped with the lamp.
ASHTRAY
The ashtray is located in the lower portion of the instru-
ment panel. In case of cleaning the ashtray up, remove
the ashtray by pushing the upper button and clean it up.
The ashtray lamp is optional.
INSTRUMENT PANEL VENTS
The center and the side vents in the instrument panel
can be adjusted up and down and from side to side. The
side vents can also be aimed toward the side windows in
order to defog them.
GLOVE BOX
The glove box can be opened by pulling up on the latch
handle. The glove box must be removed in order to gain
access to the passenger-side airbag module.
DIGITAL CLOCK
The digital clock is located in the instrument panel, be-
low the defroster grille. The clock is capable of a 12 –
hour display.
INSTRUMENT CLUSTER
The instrument cluster is located above the steering col-
umn and in the instrument cluster trim panel. The instru-
ment cluster contains the instruments that provide the
driver with vehicle performance information. The instru-
ment cluster contains a speedometer, an odometer, a
trip odometer, a temperature gauge, a fuel gauge, and
several indicator lamps. For replacement of the indicator
lamp bulbs contained in the instrument cluster, refer to
“Instrument Cluster Indicator Lamps Specifications” in
this section.
SPEEDOMETER/ODOMETER/TRIP
ODOMETER
The speedometer measures the speed of the vehicle. It
consists of an instrument cluster gauge connected to
the vehicle speed sensor on the transaxle output shaft.
The odometer measures the total distance the vehicle
has traveled since it was manufactured. It consists of an
instrument cluster gauge connected to the vehicle
speed sensor on the transaxle output shaft.
The trip odometer measures the distance the vehicle
has traveled since the odometer was last reset. It con-
sists of an instrument cluster gauge connected to the
vehicle speed sensor on the transaxle output shaft. The
trip odometer can be reset to zero at any time so that the
driver can record the distance traveled from any starting
point.
FUEL GAUGE
The fuel gauge consists of an instrument cluster gauge
connected to a sending unit in the fuel tank.
The fuel gauge indicates the quantity of fuel in the tank
without the ignition switch position.
TEMPERATURE GAUGE
The temperature gauge consists of an instrument clus-
ter gauge connected to a temperature sensor that is in
contact with the circulating engine coolant.
The temperature gauge indicates the temperature of the
coolant. Prolonged driving or idling in very hot weather
may cause the pointer to move beyond the center of the
gauge. The engine is overheating if the pointer moves
into the red zone at the upper limit of the gauge.
INSTRUMENT CLUSTER INDICATOR
LAMPS
The instrument cluster contains indicator lamps that in-
dicate the functioning of certain systems or the exis-
tence of potential problems with the operation of the
vehicle. The indicator lamps are replaceable. For re-
placement of the indicator lamps contained in the instru-
ment cluster, refer to “Instrument Cluster Indicator
Lamps Specifications” in this section.

INSTRUMENTATION/DRIVER INFORMATION 9E–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
INSTRUMENT PANEL ASSEMBLY
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D19B401A
1. Tie–Bar
2. Tie–Bar Center
3. Instrument Panel Guide
4. Defroster Grille
5. Instrument Panel Upper Cap
6. Passenger’s Airbag Blank Cover
7. Demister Grille
8. Side Ventilation Grille
9. Glove Box Bracket
10. Glove Box11. Instrument Cluster Housing Molding
12. Center Ventilation Grille
13. Switch Blank Cover (Fog Lamp Switch)
14. Hazard Warning Switch
15. Immobilizer LED Indicator Switch
16. Ashtray Bracket
17. Ashtray
18. Ashtray Lamp
19. Cigar Lighter Housing
20. Instrument Cluster Bracket
21. Instrument Panel

9E–6 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D19B302B
HVAC PANEL ILLUMINATION
Condition Probable Cause Correction
HVAC Panel Illumination
Inoperative
The open or a short in the power supply
circuit to the fuse Ef12.
Repair or Replace the wiring
harness.

Fuse Ef12 is blown.
Replace the fuse Ef12






The circuit between the fuse Ef12 and the
terminal 2 of the HVAC panel illumination
connector is the open circuit or a short
circuit.



Repair or Replace the wiring
harness.







Faulty the HVAC panel illumination
connector.



Repair or Replace the
instrument panel illumination
connector.

HVAC panel illumination bulb is blown.
Replace the bulb.

Open ground (G201) circuit.
Repair the open ground
circuit.

INSTRUMENTATION/DRIVER INFORMATION 9E–9
DAEWOO M-150 BL2
D109B504
ASHTRAY
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the ashtray from the ashtray bracket.

Pull off the ashtray by pressing the upper button.
D19B505A
2. Remove the ashtray bracket from the instrument pan-
el.

Remove the screws (1).

Remove the ashtray bracket (3).
D109B506
Installation Procedure
1. Install the ashtray bracket with the screws.
2. Install the ashtray.
D109B507
INSTRUMENT CLUSTER TRIM PANEL
VENTS
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the instrument cluster trim panel from the in-
strument panel. Refer to “Instrument Cluster Trim
Panel” in this section.
2. Remove the vent from the instrument cluster trim
panel.

Remove the screws (1).

Remove the vents (2).

9E–10 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D109B508
Installation Procedure
1. Install the vents to the instrument cluster trim panel
with the screws.
2. Install the instrument cluster trim panel. Refer to “In-
strument Cluster Trim Panel” in this section.
D109B511
DIGITAL CLOCK
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Pry off the defroster grille.
3. Unlock the locking of the digital clock.
a. Digital clock.
D109B512
4. Remove the digital clock from the instrument panel.

Disconnect the electrical connector (1).

Remove the digital clock (2).
D109B513
Installation Procedure
1. Connect the electrical connector.
2. Install the digital clock to the instrument panel.
3. Connect the negative battery cable.
4. Set the clock.

INSTRUMENTATION/DRIVER INFORMATION 9E–11
DAEWOO M-150 BL2
D109B509
GLOVE BOX
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the hinge pins at the base of the glove box.
D109B510
2. Remove the glove box from the instrument panel.
D109B509
Installation Procedure
1. Install the glove box to the instrument panel with the
hinge pins.
D19B514A
INSTRUMENT CLUSTER
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster trim panel from the in-
strument panel. Refer to “Instrument Cluster Trim
Panel” in this section.
3. Remove the instrument cluster assembly from the in-
strument panel.

Remove the screws (1).

Disconnect the electrical connector and the
speedometer cable (2).

Remove the instrument cluster (3).

9E–12 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D19B515A
Installation Procedure
1. Connect the electrical connector and the speedom-
eter cable.
2. Install the instrument cluster assembly to instrument
panel with screws.
3. Install the instrument cluster trim panel to the instru-
ment panel. Refer to “Instrument Cluster Trim Pan-
el” in this section.
4. Connect the negative battery cable.
D109B516
INSTRUMENT PANEL
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the driver’s airbag module from the steer-
ing wheel. Refer to Section 8B, Supplemental Inflat-
able Restraints (SIR) (For the vehicle equipped with
the airbag).
3. Remove the steering wheel from the steering col-
umn. Refer to Section 6E, Steering Wheel and Col-
umn.
4. Remove the steering column trim cover. Refer to
Section 6E, Steering Wheel and Column.
5. Remove the signal lamp switch and the wiper
switch. Refer to Section 6E, Steering Wheel and
Column.
6. Pry off the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
7. Remove the instrument cluster trim panel from the
instrument panel.

Remove the screws (1)

Using a flathead screwdriver, remove the instru-
ment cluster trim panel (2).
Notice: To prevent the instrument panel damage, cover
the flathead screwdriver with a soft cloth.
D109B517
8. Remove the hood latch release lever from the in-
strument panel. Refer to Section 9R, Body Front
End.
9. Remove the glove box assembly from the instru-
ment panel. Refer to “Glove Box” in this section.
10. Remove the passenger’s airbag module from the in-
strument panel. Refer to Section 8B, Supplemental
Inflatable Restraints (SIR) (For vehicle equipped
with the airbag).
11. Put aside the floor console after removing the
screws (1).

INSTRUMENTATION/DRIVER INFORMATION 9E–13
DAEWOO M-150 BL2
D109B518
12. Remove the instrument cluster assembly. Refer to
“Instrument Cluster” in this section.
13. Remove the A/C controller from the instrument. Re-
fer to Section 7B, Manual Control Heating, Ventila-
tion, and Air Conditioning System.
14. Remove the audio system from the instrument pan-
el. Refer to Section 9F, Audio Systems.
15. Disconnect the cigar lighter connector.
16. Disconnect the ashtray lamp if equipped.
D109B519
17. Disconnect the ALDL connector.

Remove the screws (1).

Disconnect the ALDL connector (2).
D109B520
18. Remove the instrument trim panel assembly.

Remove the bolts after removing the caps (1).

Remove the screws on the side plate (2).

Remove the tie–bar retaining bolts on the lower
panel (3).

Remove the instrument trim panel assembly (4).
D109B521
Installation Procedure
1. Install the instrument trim panel assembly with the
bolts and screws.
2. Connect the ALDL connector with the screws.
3. Connect the ashtray lamp if equipped with.
4. Connect the cigar lighter connector.
5. Install the audio system to the instrument panel. Re-
fer to Section 9F, Audio Systems.
6. Install the A/C controller to the instrument panel.
Refer to Section 7B, Manual Control Heating, Ven-
tilation, and Air Conditioning System.