2002 Lexus ES300 Owner's Manuals (in English)

AUDIO
196
Push “AM”, “FM”, “TAPE” or “DISC” to turn on that mode.
The selected mode turns on directly.
Push these buttons if you want to switch from one mode to
another.
If the tape or disc is not set, the cassette player or compact disc
player does not turn on.
You can turn off the cassette player by ejecting the cassette
tape. If the audio system was previously off, then the entire
audio system will be turned off when you eject the cassette
tape. If another function was previously playing, it will come on
again.In the “TAPE” or “CD” mode, the applicable functions are
shown in the lowest part of the display. Push the switch
just below to turn on each function.
(b) Tone and balance
How good an audio program sounds to you is largely
determined by the mix of the treble, midrange, and bass
levels. In fact, different kinds of music and vocal programs
usually sound better with different mixes of treble, midrange,
and bass.
A good balance of the left and right stereo channels and of the
front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of one group of sounds while decreasing the volume
of another.

AUDIO
197
Each time you push the “AUDIO CONTROL” knob, the
display changes as in the following. To adjust the tone
and balance or turn on or off the automatic sound
levelizer, turn the knob.
BAS: Adjusts lowpitched tones.
MID: Adjusts midpitched tones.
TRE: Adjusts highpitched tones.
FAD: Adjusts the sound balance between the front and rear
speakers.
BAL: Adjusts the sound balance between the right and left
speakers.
ASL: Turns on or off the automatic sound levelizer.
Automatic sound levelizer: When the audio sound becomes
difficult to be heard due to road noise, wind noise, etc. during
driving, the system adjusts to the optimum volume and tone
quality according to the noise level. While the automatic sound
levelizer is on, “ASL” appears on the display. (c) Your radio antennas
The wire antenna is mounted inside the rear window.
NOTICE

When cleaning the inside of the rear window, be
careful not to scratch or damage the wire antenna.
 Putting a window tint (especially, conductive or
metallic type) on the rear window may affect the
reception of radio or mobile telephone. For the
installation of the window tint, consult with your
Lexus dealer.
(d) Your cassette player
When you insert a cassette, the exposed tape should face to
the right.
NOTICE
Do not oil any part of the cassette player, and do not
insert anything except a cassette tape into the slot.

AUDIO
198(e) Your automatic changer
Your automatic changer can store up to 6 discs and play
selected discs or continuously play all the discs set in the
player.
When
you set discs into the player, make sure their labels face
up. If not, the player will display “ERROR1” and the disc
number.
NOTICE
 Never try to disassemble or oil any part of the
compact disc player. Do not insert anything except
a compact disc into the slot.
 Do not insert a disc upon another one.
The player is intended for use with 12 cm (4.7 in.) discs only.
Radio operation
(a) Listening to the radio
Push these buttons to choose either an AM or FM station.
“AM”, “FM1”, “FM2” or “FM TYPE” appears on the d\
isplay.

AUDIO
199
Turn this knob to the right to step up the station band or
to the left to step down.
Your radio automatically changes to stereo reception when a
stereo broadcast is received. “ST” appears on the display. If
the signal becomes weak, the radio reduces the amount of
channel separation to prevent the weak signal from creating
noise. If the signal becomes extremely weak, the radio
switches from stereo to mono reception. In this case, “ST”
disappears from the display.(b) Presetting a station
1. Tune in the desired station.
2. Push
one of the station selector buttons ( 16 ) and hold
it until a beep is heard. This sets the station to the button
and the button number ( 16 ) appears on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse.

AUDIO
200(c) Selecting a station
Your Lexus has an electronic tuning radio (ETR). Tune in the
desired station using one of the following methods.
Seek tuning: Push the “SEEK” button. The radio will begin
seeking up
or down for a station of the nearest frequency and
will stop on reception. Each time you push the button, the
stations will be searched out one after another.
Preset tuning: Push the button ( 16 ) for the station you want.
The button number ( 16 ) and station frequency appear on the
display.
Manual tuning: Turn the “TUNE” knob. The radio will step up
or down to another frequency.
To scan all the frequencies: Push the “SCAN” button briefly.
“SCAN” appears on the display. The radio will find the next
station up the band, stay there for a few seconds, and then
scan again. To select a station, push the “SCAN” button a
second time.
To scan the preset stations: Push the “SCAN” button until
you hear a beep. “P .SCAN” appears on the display . The radio
will tune in the next preset station up the band, stay there for
a few seconds, and then move to the next preset station. To
select a station, push the “SCAN” button a second time.

AUDIO
201
(d) RDS (Radio Data System)
AF (Alternative Frequency) function: When the RDS is
turned on, a station providing good reception is
automatically selected if current reception worsens.
When you push the “RDS”
button briefly during FM reception,
the RDS turns on. “RDS” and “RDS SEARCH” appear on the
display and the radio starts to search RDS stations.
If no RDS stations can be found, “NOTHING” appears and the
display returns to the previous mode.
If RDS stations are found, “FOUND **ST” appears on the
display (** indicating the number of stations which are found)
in the FM TYPE mode and the RDS stations are preset by
program type.
To turn off the RDS, push the “RDS” button until you hear a
beep. TYPE (Program type):
When you push the “TYPE” button while receiving an RDS
station, the current program type appears on the display.
Each time you push the “TYPE” button, the program type
changes as in the following:

ROCK
 EASY LIS (Easy listening)
 CLS/JAZZ (Classical music and jazz)
 R&B (Rhythm and Blues)
 INFORM (Information)
 RELIGION
 MISC
 ALERT (Emergency message)

AUDIO
202Emergency broadcast:
If an emergency broadcast is received during reception of
other
than AM broadcasting, you will hear a beep and “ALERT”
appears on the display. Then an emergency broadcast will
start. The volume of the emergency program is the same as
TA volume level. TRAF (Traffic) function: A station that regularly
broadcasts traffic information is automatically located
and broadcasts when the program starts.
When you push the “TRAF” button, “TRAF SEEK” appears on
the display and the radio will start seeking any traffic program
station.
If no traf
fic program station is found, “NO TRAF INFO” appears
on the display for a few seconds and the display returns to the
previous mode. However, if the “TRAF” button is pushed while
in “TAPE” or “CD” mode, the radio will start seeking traffic
program stations again after 20 seconds.
If a traf fic program station is found, the name for traffic program
station is displayed for a while until a traffic announcement is
received. On reception of a traf fic announcement, you will hear
a beep and “TRAF ANNOUNCE” appears on the display for a
few seconds.
After the traffic announcement program is over , a beep sounds
and the display returns to the previous mode.
TA volume level: The volume of the traffic information
program can be adjusted independently by turning the “VOL”
knob while a traffic program station is received.

AUDIO
203
Radio text message:
If the radio receives a radio text message during FM reception,
“MSG” and a text message appears on the display. After the
text message goes off, “MSG” also goes off.
After the text message goes off from the display, pushing the
“MSG” button during message reception shows the text
message again on the display.
The RDS audio system can store three messages consisting
of 64 characters in memory. To store a message in memory,
push the “MSG” button until you hear a beep.
If three messages are already stored in memory, the oldest
message will be overwritten by the new message.
To recall a radio text message, push the “MSG” button. Each
time you push the button, the available message will be
displayed beginning with the newest one.
If there is no radio text message in memory and when no
message is received, “NO MSG STORED” appears on the
display. After this, the display returns to the previous mode.