2002 ISUZU AXIOM battery

8J±8EXTERIOR/INTERIOR TRIM
Door Mirror Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the door mirror cover (3).
3. Remove the door mirror assembly (1).

Remove the three nuts and disconnect the
connector (2).
635R200006
Installation
To install, follow the removal steps in the reverse order.
Interior Mirror Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the covers (1).
3. Remove the interior mirror assembly (4).

Pull the interior mirror up with the stay and remove
the interior mirror from the base (3).

Disconnect the connector (2).
720R200004
Installation
To install, follow the removal steps in the reverse order.

EXTERIOR/INTERIOR TRIM8J±9
Interior Trim Panels
Interior Trim Panels and Associated Parts
643R200003
Legend
(1) Assist Grip (Front & Rear)
(2) Door Finisher (Front & Rear)
(3) Upper Quarter Pillar Trim Cover
(4) Upper Rear Pillar Trim Cover
(5) Rear Roof Trim Cover
(6) Tailgate Weather Strip
(7) Multi Hook(8) Rear End Floor Trim Cover
(9) Lower Quarter Trim Cover
(10) Sill Plate (Front & Rear)
(11) Lower Center Pillar Trim Cover
(12) Upper Center Pillar Trim Cover
(13) Dash Side Trim Cover
(14) Front Pillar Trim Cover
Removal
1. Disconnect the battery ground cable.
2. Remove the sill plates (Front & Rear).
3. Remove the dash side trim cover.
4. Remove the lower center pillar trim cover.

Remove the lower anchor bolt cover and lower
anchor bolt from the front seat belt.

Pry the trim cover with the clips from the body panel.
5. Remove the door finishers (Front & Rear).

8J±12EXTERIOR/INTERIOR TRIM
Headlining
Parts Location
666R200001
Legend
(1) Interior Trim Panels
(2) Headlining (Without Sunroof)
(3) Clip
(4) Luggage Room Light
(5) Assist Grip
(6) Headlinng (With Sun Roof)(7) Sunroof Finisher (With Sunroof)
(8) Overhead Console/Sunroof Switch (With
Sunroof)
(9) Dome Light
(10) Overhead Console (Without Sunroof)
(11) Sunvisors
(12) Sunvisor Holder
Removal
1. Disconnect the battery ground cable.
2. Remove the interior trim panels.

Refer to
Interior Trim Panels in this section.
3. Remove the dome light.

Remove the dome light lens and the fixing screws.
Disconnect the dome light connectors.

8J±14EXTERIOR/INTERIOR TRIM
Overhead Console
Parts Location (W/O Sunroof)
743R200005
Legend
(1) Overhead Console Bracket
(2) Harness Connector
(3) Head Lining(4) Room Mirror
(5) Overhead Console Assembly
(6) Front Door Finisher
(7) Front Assist Grip
Removal
1. Disconnect the battery ground cable.
2. Remove the overhead console assembly.

Open the lid and remove the two screws.

Disconnect the harness connector.
3. Remove the sunvisor and sunvisor holder. (right and
left)
4. Remove the front assist grip. (right and left)
5. Remove the front piller trim cover.6. Remove the front door finisher.

Remove the upper side of door finisher.
7. Remove the interior mirror.

Refer to
Interior Mirror in this section.
8. Remove the overhead console bracket.

Remove the two screws.
Installation
To install, follow the removal steps in the reverse order.

EXTERIOR/INTERIOR TRIM8J±15
Parts Location (W/ Sunroof)
743R200004
Legend
(1) Sunroof Weatherstrip
(2) Overhead Console Bracket(3) Head Lining
(4) Overhead Console
(5) Clip Position
Removal
1. Disconnect the battery ground cable.
2. Remove the overhead console.

Open the lid and remove the two screws.

Pull the over head console at the two clip positions.

Disconnect the harness connectors.
3. Remove the head lining.

Refer to
Head Lining in this section.
4. Remove the overhead console bracket.

Remove the five fixing screws.
Installation
To install, follow the removal steps in the reverse order.

8J±20EXTERIOR/INTERIOR TRIM
Power Door Mirror System
General Description
The system consists of the starter switch, door mirror
switch, rear defogger/mirror defogger switch and door
mirrors on both sides.
When the door mirror switch is operated with the starter
switch at either ªACCº or ªONº position, the motor in the
door mirror (on either side) rotates to allow the horizontal
and vertical adjustment of mirror angles.
When the rear defogger/mirror defogger switch is turned
ªONº with the starter switch ªONº, the heater of the left
and right mirrors and the tailgate glass are activated.
Door Mirror Switch
Removal
1. Disconnect the battery ground cable.
2. Remove the instrument panel lower cover (2).
Refer to the
Instrument Panel Assembly in Body
Structure section.
3. Remove the door mirror switch (1).
825RW094
Rear Defogger/Mirror Defogger Switch
Refer to the Rear Defogger/Mirror switch removal and
installation steps in Lighting System section.
Door Mirrors
Refer to Door Mirror Assembly in this section.

EXTERIOR/INTERIOR TRIM8J±21
Power Window System
General Description
The power window system consists of power window
switches and power window motors on driver and
passenger sides and power window relay. With the starter
switch in ªONº position, the battery voltage is supplied
through power window relay to the power window
switches on driver and passenger sides. Selection of up
or down switch changes the motor rotating direction to
open or close the window.
When the power window ªLOCKº switch on the driver side
is pressed, the power source for the other switches are
disconnected causing the power window operation to
seize.
Power Window Switch Driver Seat
Side
Removal
1. Disconnect the battery ground cable.
2. Remove the switch (1).

Pull out the switch by pushing the spring with the tip
of a screwdriver.

Disconnect the connector.
635R200002
Installation
To install, follow the removal steps in the reverse order.
Front Passenger Seat Side
Removal
1. Disconnect the battery ground cable.
2. Remove the switch (1).

Pull out the switch by pushing the spring (2) with the
tip of a screwdriver.

Disconnect the connector.
825R200025
Installation
To install, follow the removal steps in the reverse order.
Rear-Left and Right Sides
Removal
1. Disconnect the battery ground cable.
2. Remove the rear power window switch (1).

Pull out the switch by pushing the spring with the tip
of a screwdriver.

Disconnect the connector.
655R200004
Installation
To install, follow the removal steps in the reverse order.

8J±22EXTERIOR/INTERIOR TRIM
Power Window Motor
Driver Seat Side
Removal
1. Disconnect the battery ground cable.
2. Remove the window regulator assembly (2).

Refer to the
Window Regulator and Glass removal
steps in Body Structure section.
3. Remove the power window motor (1).

Remove three screws.
635R200007
Installation
To install, follow the removal steps in the reverse order.
Front Passenger Seat Side
Removal and Installation
Refer to the
Front Window Motor Ð Driver Seat side
removal and installation steps in this section.
Rear-Right Side
Removal
1. Disconnect the battery ground cable.
2. Remove the rear window regulator assembly (2).

Refer to the
Rear Window Regulator and Glass
removal steps in Body Structure section.
3. Remove the power window motor (1).

Remove three screws.
655R200006
Installation
To install, follow the removal steps in the reverse order.
Rear-Left Side
Removal and Installation
Refer to the
Rear Power Window Motor Ð Right Side
removal and installation steps in this section.