2002 ISUZU AXIOM air condition

1A±10
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
10. Pull out the door lever while raising up the catch of the
door lever.
11. Remove clip.
Installation
To install, follow the remove steps in the reverse order,
noting the following points:
1. Apply grease to the mode sub-lever and to the
abrasive surface of the heater unit.
2. After installing the link unit, check to see if the link unit
operates correctly.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±11
Heater Temperature Control Link Unit
Disassembled View
860R200003
Legend
(1) Case (Temperature control)
(2) Door Lever
(3) Clip
(4) Rod(5) Clip
(6) Sub-lever
(7) Mix Actuator
(8) Heater Unit
Removal
1. Disconnect the battery ground cable.
2. Drain engine coolant.
3. Discharge and recover refrigerant (with air
conditioning).

Refer to
Refrigerant Recovery in this section.
4. Remove heater unit.

Refer to
Heater Unit in this section.
5. Remove mix actuator.
6. Remove the case (Temperature control) from the
heater unit.
7. Remove rod.
8. Remove sub-lever.
9. Pull out the door lever while raising up the catch of the
door lever.
10. Remove clip.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Apply grease to the sub-lever and to the abrasive
surface of the heater unit.
2. After installing the link unit, check to see if the link unit
operates correctly.

1A±12
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Blower Assembly
Blower Assembly and Associated Parts
873R200004
Legend
(1) Instrument Panel Assembly
(2) Blower Assembly(3) Evaporator Assembly
(4) Heater Unit
Removal
1. Disconnect the battery ground cable.
2. Discharge and recover refrigerant (with air
conditioning).

Refer to
Refrigerant Recovery in this section.
3. Remove instrument panel assembly.

Refer to
Instrument Panel Assembly in Body and
Accessories section.
4. Disconnect power transistor connector.
5. Remove evaporator assembly.

Refer to
Evaporator Assembly in this section.
6. Disconnect blower motor/intake actuator connector.
7. Remove blower assembly.
Installation
To install, follow the removal steps in the reverse order.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±13
Blower Link Unit and / or Mode door
Disassembled View
873R200001
Legend
(1) Blower Assembly
(2) Upper Case
(3) Mode Door
(4) Lower Case(5) Max High Relay
(6) Intake Actuator
(7) Sub Lever
(8) Door Lever
Removal
1. Disconnect the battery ground cable.
2. Discharge and recover refrigerant (with air
conditioning).

Refer to
Refrigerant Recovery in this section.
3. Remove blower assembly.

Refer to
Blower Assembly in this section.
4. Remove intake actuator.
5. Remove max high relay.
6. Remove lower case.
7. Separate the upper case and slit the lining parting
face with a knife.
873RS002

1A±14
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
8. Pull out the mode door while raising up the catch of
door lever.
9. Remove sub-lever.
10. Remove door lever.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Apply grease to the door lever and to the abrasive
surface of the upper case.
2. Apply an adhesive to the parting face of the lining
when assembling the upper case.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±15
Blower Motor
Blower Motor and Associated Parts
873RS004
Legend
(1) Blower Motor Connector
(2) Blower Motor Assembly
(3) Clip(4) Fan
(5) Blower Motor
(6) Attaching Screw
Removal
1. Disconnect the battery ground cable.
2. Remove blower motor connector.
3. Remove attaching screw.
4. Remove blower motor assembly.
5. Remove clip.
6. Remove fan.
7. Remove blower motor.
Installation
To install, follow the removal steps in the reverse order.

1A±16
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Rear Heater Duct, Defroster Nozzle and Ventilation Duct
Rear Heater Duct, Defroster Nozzle, Ventilation Duct and Associated Parts
840R200009
Legend
(1) Defroster Nozzle
(2) Cross Beam Assembly
(3) Center Ventilation Duct and Side Defroster
Duct(4) Instrument Panel Bracket W/Suspension
Control Unit
(5) Instrument Panel Assembly
(6) Rear Heater Duct
(7) Ventilation Lower Duct
Removal
1. Disconnect the battery ground cable.
2. Remove instrument panel assembly.

Refer to
Instrument Panel Assembly in Body and
Accessories section.
3. Remove center ventilation duct and side defroster
duct.

Remove 5 screws.4. Remove instrument panel brackets w/suspension
control unit.

Refer to
Cross Beam Assembly in Body and
Accessories section.
5. Remove cross beam assembly.

Refer to
Cross Beam Assembly in Body and
Accessories section.
6. Remove ventilation lower duct.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±17
7. Remove rear heater duct.

Remove foot rest carpet and 3 clips.
8. Remove defroster nozzle.
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1. Connect each duct and nozzle securely leaving no
clearance between them and making no improper
matching.