2002 HONDA ACCORD COUPE Owners Manual

Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Put the radiator cap back on.
Tighten it f ully.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
3. 2. 4.
5.6.
Cooling Syst em
Maint enance254
4 4-
-c
cy yl liinn d
de
err m
m o
od
de
ellss 6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss
R
RA
A D
DI
IAA T
TO
OR R C
CAA P
P
R
RAA D
DI
IAA T
TO
OR R C
CAA P
P 4
4--c
cy yl liinn d
de
err m
m o
od
de
ellss R
REES
SE ER
RV V E
E T
TA
A N
NK K

CONT INUED
Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents.Turn the ignition ON (II). Turn
the heater temperature control
dial to maximum heat (climate
control to 90°F/32°C). Turn of f
the ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Remove the radiator cap.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance
done by a skilled mechanic.
1.
2.
Cooling Syst em
Maint enance
Replacing Engine Coolant
255
R RE ES
SE ER
RV V E
E T
TA
A N
NK K
6
6- -c
cy yl liinn d
de
err m
m o
od
de
ellss 4
4-
-c
cy yl liinn d
de
err m
m o
od
de
ellss

4-cylinder models6-cylinder models
Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Remove the drain
bolt and washer f rom the engine
block.Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Loosen the drain
bolt.
3.
Maint enance
Cooling Syst em
256
6 6-
-c
cy yl liinn d
de
err m
m o
od
de
ellss 4
4--c
cy yl liinn d
de
err m
m o
od
de
ellss 6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss D
DR
RAA I
INN B
BOOL LTT
D
D
R
RAA I
INN
P
P L
LUUG G
D
D
R
RAA I
INN
B
BO OL LTT D
D
R
RAA I
INN P
PL
LUUG G

CONT INUED
Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.When removing the reserve tank,
f irst remove the cruise control cable
and the ground cable f rom their clips.
Af ter installing the tank back in
place, put the cables back in their
clips.
4.6-cylinder models
Cooling Syst em
Maint enance257
R RE
ES
SE ER
RV V E
E T
TA
A N
NK K
6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss
4
4- -c
cy yl liinn d
de
err m
m o
od
de
ellss R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K
R
RE ES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
H
H O
OL LDD E
ER
R R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
H
H O
OL LDD E
ER
R
G
GR
ROOU UNNDD C
CAA B
BLLEE
C
CR RUUI ISSE E C
COON NTTR
RO OL L C
CAA B
BLLEE

4-cylinder models6-cylinder models 6-cylinder models
With automatic transmission:
With 5-speed manual transmission:
4-cylinder models
4-cylinder models 6-cylinder models
Put a new washer on the drain bolt,
then reinstall the drain bolt in the
engine block. Tighten it securely.
Tightening torque:
Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque: When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Loosen the bleeder bolt on top of
the engine.
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.The cooling system capacity is:
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles.
Pour coolant into the radiator up
to the base of the f iller neck.
7.
6. 5.
Cooling Syst em
Maint enance258
B BL
LEE E
ED
D E
ER
R B
BOOL LTT
61 lbf·ft (83 N·m , 8.5 kgf·m)
7 lbf·ft (10 N·m , 1.0 kgf·m) 1.43 US gal (5.4
, 1.19 Imp gal)
1.45 US gal (5.5
, 1.21 Imp gal)
1.48 US gal (5.6, 1.23 Imp gal)

Fill the radiator with coolant up to
the base of the f iller neck.
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
Install the radiator cap, and
tighten it to the first stop.Start the engine and let it run until
the radiator cooling f an comes on
at least twice. Then stop the
engine.
Remove the radiator cap. Pour
coolant into the radiator up to the
base of the f iller neck and into the
reserve tank up to the MAX mark.
Start the engine and hold it at
1,500 rpm until the radiator f an
comes on. Turn of f the engine.
Check the coolant level in the
radiator and add coolant if needed.
Install the radiator cap, and
tighten it fully.
If necessary, f ill the reserve tank
to the MAX mark. Install the
reserve tank cap.
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine.
9.
10. 11. 12.
13.
14.
15.
16.
8.
Cooling Syst em
Maint enance259
4 4-
-c
cy yl liinn d
de
err m
m o
od
de
ellss F
Fiillll u
u p
p t
too h
he
erree
F
FI
ILLL LEE R
R N
NEEC
CK K F
FIILLL LEE R
R N
NEEC
CK K
6
6- -c
cy yl liinn d
de
err m
m o
od
de
ellss
F
Fiillll u
u p
p t
too h
he
erree

Check the level in the windshield
washer reservoir at least monthly
during normal usage. In bad weather,
when you use the washers of ten,
check the level every time you stop
for fuel.
The windshield washer reservoir is
located behind the driver’s side
headlight.
The windshield washer reservoir is
located behind the passenger’s side
headlight.
The low washer level indicator will
light when the level is low (see page).
Check the reservoir’s f luid level by
removing the cap and looking at the
level gauge attached to the cap. Fill the reservoir with a good-quality
windshield washer f luid. This
increases the cleaning capability and
prevents f reezing in cold weather.
When you ref ill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer f luid
on a clean cloth. This will help to
condition the blade edges.
62
4-cylinder models
6-cylinder modelsOn Canadian models
Windshield Washers
Maint enance260
L LEE V
V E
EL
L G
GAAU
UG GEE
4
4- -c
cy yl liinn d
de
err m
m o
od
de
ellss 6
6--c
cy yl liinn d
de
err m
m o
od
de
ellss
L
LE
E V
V E
EL
L G
GAAU
UG GEE
Do not use engine antif reeze or a
vinegar/water solution in the
windshield washer reservoir.
Antif reeze can damage your car’s paint,
while a vinegar/water solution can
damage the windshield washer pump.
Use only commercially-available
windshield washer f luid.

Check the f luid level with the engine
at normal operating temperature.Insert the dipstick all the way into
the transmission securely as
shown in the illustration.
Remove the dipstick (yellow loop)
f rom the transmission and wipe it
with a clean cloth. Park the car on level ground. Shut
of f the engine.
1.
2. 3.
CONT INUED
Automatic Transmission
T ransmission Fluid
Maint enance261
U UP
PP
PE
ER
R M
M A
AR
RKK
L
LO OW WE ER
R M
M A
AR
RKK
D
D I
IPP S
ST TI
ICCK K
4
4- -c
cy yl liinn d
de
err m
m o
od
de
ellss D
D
I
IPP S
ST TI
ICCK K
6
6- -c
cy yl liinn d
de
err m
m o
od
de
ellss D
DI
IPP S
ST TI
ICCK K 4
4--c
cy yl liinn d
de
err m
m o
od
de
ellss