Page 289 of 375

´
Wheel: Tires that are marked ‘‘M S’’ or
‘‘All Season’’ on the sidewall have an
all-weather tread design. They
should be suitable f or most winter
driving conditions. Tires without
these markings are designed f or
optimum traction in dry conditions.
They may not provide adequate
perf ormance in winter driving.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.
If you ever need to replace a wheel,
make sure the wheel’s specif ications
match those of the original wheel
that came on your car. Replacement
wheels are available at your Honda
dealer. TheABSworksbycomparingthe
speed of the wheels. When replacing
tires, use the same size originally
supplied with the car. Tire size and
construction can af f ect wheel speed
and may cause the system to work
inconsistently.
See page f or inf ormation about
DOT Tire Quality Grading. Tire:
(Special Edition, EX, and the U.S.
LX)
(U.S. LX-V6)
(EX-V6) (Special Edition, EX, and the U.S.
LX)
(U.S. LX-V6)
(EX-V6)348
Tires
Maint enance
Wheels and T ires Winter Driving
286
P205/60R16 91V P205/65R15 92V
P195/65R15 89H 16x61/2JJ 15x61/2JJ
15x6JJ
Page 290 of 375

4-cylinder models6-cylinder models
If you mount snow tires on your
Honda, make sure they are radial
tires of the same size and load range
as the original tires. Mount snow
tiresonallfourwheelstobalance
your car’s handling in all weather
conditions. Keep in mind the traction
provided by snow tires on dry roads
may not be as high as your car’s
original equipment tires. You should
drive cautiously even when the roads
areclear.Checkwiththetiredealer
f or maximum speed recommenda-
tions. Mount traction devices (link-type or
cable-type) only when required by
driving conditions or local laws.
Make sure they are the correct size
f or your tires. Install them only on
the front tires.
If link-type traction devices are used,
they must be SAE class ‘‘S’’. Cable-
type traction devices can also be
used.
Because your Honda has limited tire
clearance, mount only SAE Class ‘‘S’’
cable-type traction devices.
Link-type ‘‘chains’’ should not be
used. No matter how tight they seem
to be installed, they can come into
contact with the body and
suspension, causing serious damage.When installing traction devices,
f ollow the manuf acturer’s
instructions and mount them as
tightly as you can. Drive slowly with
them installed. If you hear them
coming in contact with the body or
chassis, stop and investigate. Make
sure the traction devices are
installed tightly, and that they are
not contacting the brakes or
suspension. Remove them as soon as
youstartdrivingonclearedroads.
Snow T ires
T ire ChainsA ll Models
Tires
Maint enance287
Traction devices that are the wrong
size or improperly installed can
damage your car’s brake lines,
suspension, body, and wheels. Stop
driving if they are hitting any part of
the car.
Page 291 of 375
Check the operation of your car’s
exterior lights at least once a month.
A burned out bulb can create an
unsaf e condition by reducing your
car’s visibility and the ability to
signal your intentions to other
drivers.
Lights
Maint enance288
H HE
EA
A D
DL
LIIGGH HT
T H
HI
IGGH H B
BEEA
A M
M
T
TU
UR RNN S
SIIGGN NAAL
L//S
SI IDD E
E
M
M A
AR
RKKEER
R L
LIIGGH HT
T
H
H
E
EA
A D
DL
LIIGGH HT
T L
LOOW W B
BEEA
A M
M
P
P A
A R
RKKIINNG G L
LIIGGH HT
T
Page 292 of 375
Check the f ollowing:Headlights (low and high beam)
Parking lights
Taillights
Brake lights
High-mount brake light
Turn signals
Back-up lights
Hazard light f unction
License plate light
Side marker lights
Daytime running lights
(Canadian models)
If you f ind any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on pages and to determine what type of
replacement bulb is needed. 347 345
Lights
Maint enance289
T T
U
UR RNN S
SIIGGN NAAL
L//T
T A
A I
ILLL LIIGGH HT
T H
HI
IGGH H-
-M
M O
OUUNNTT B
BRRAA K
KEE L
LIIGGH HT
T
B
BA A C
CKK--U
UP P L
LIIGGH HT
T
R
RE EA
A R
R S
SIIDD E
E M
M A
AR
RKKEER
R L
LIIGGH HT
T S
STTO
OP P/
/T
T A
A I
ILLL LIIGGH HT
T L
LI
ICCE EN
NS SEE
P
P L
LAA T
TE
E L
LIIGGH HT
TS
S
Page 293 of 375

Your car has two bulbs on each side,
four in total. Make sure you are
replacing the bulb that is burned out.
Your car uses halogen headlight
bulbs. When replacing a bulb, handle
it by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Theheadlightswereproperlyaimed
when your car was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustment of the
headlights should be perf ormed by a
Honda technician or other qualif ied
mechanic.
Open the hood.
If you need to change the head-
light bulb on the passenger’s side,
remove the radiator reserve tank
and the air intake duct.
If you need to change the
headlight bulb on the driver’s side,
remove the radiator reserve tank.
1.
4-cylinder models
6-cylinder models
Replacing a Headlight Bulb
Headlight A iming
Lights
Maint enance290
4 4- -c
cy yl liinn d
de
err m
m o
od
de
ellss A
A
I
IRR I
INNT TA
A K
KEE
D
D U
UC CTT
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
Page 294 of 375
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.Reinstall the radiator reserve tank. (Driver’s side) Reinstall the radiator reserve tank
and the air intake duct. (Passenger’s side) Turn on the headlights to test the
new bulb. Push the electrical connector back
onto the bulb. Make sure it is on
all the way. Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
2.
3. 4.
7. 6. 5.
6-cylinder models
4-cylinder models
Lights
Maint enance291
B BU
UL LBB
T
T A
A B
B
Page 295 of 375

Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb in the socket.
Turn it clockwise to lock it in place. Remove the burned out bulb f rom
thesocketbypushingitinand
turning the bulb counterclockwise
until it unlocks.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
place by pushing on the center.
1.
3. 2.
4.5.
6.
7.
8.
9.
Replacing Front Turn Signal and
Side Marker L ight Bulbs
Lights
Maint enance292
H H
O
OL LDD I
INNG G C
CLLIIPP
Page 296 of 375

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Open the hood. The f ront parking
light is next to the headlight bulb. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the parking lights to
make sure the new bulb works.
(Passenger’s side)
Reinstall the radiator reserve tank.
(Driver’s side)
If you need to change a bulb on the driver’s side, remove the
radiator reserve tank.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
(Driver’s side)
Reinstall the power steering f luid
tank.
Reinstall the radiator reserve tank.
If you need to change a bulb on
the passenger’s side, remove the
radiator reserve tank. On the
driver’s side, remove the power
steering f luid tank. 2. 3.
1. 4.
5.
6.
4-cylinder models
6-cylinder models
6-cylinder models 4-cylinder models
Replacing a Parking L ight Bulb
Lights
Maint enance293
P P
O
OW WE ER
R S
STTE
EE
ER
RI INNG G F
FLLUUI IDD T
TA
A N
NK K
H
H O
OL LDD E
ER
R