2002.5 Peugeot 406 Owner's Manual

BOOT
Simultaneous locking or unlocking
of the boot and the doors
Turn the key a quarter turn from
A to B.
The boot is then controlled by the
remote control or the driver's door
lock.
Locking the boot only
Turn the key a quarter of a turn from
A to C. The boot is then locked,
whatever the action of the remote
control or the driver's door lock.
To return to simultaneous operation
with the doors: turn the key from
A to B. Opening the tailgate of the
7 seater estate from inside
Slide button
Aand press.
To lock the interior control, turn the
key to the left.
YOUR 406 IN DETAIL 109
29-07-2002

29-07-2002
OPENING THE BONNET
From inside:pull the handle on the
lefthand side under the fascia.
From outside: lift the catch and
raise the bonnet.
Bonnet struts
These open the bonnet and hold it
open.
To close
Lower the bonnet and release it at
the end of its travel. Check that the
bonnet is properly locked. FILLING WITH FUEL
Fill with fuel with the engine switched
off.
To open the fuel filler flap, firmly pull
the handle on the floor on the left of
the driver's seat.
If you are filling up your tank, do not
continue after the 3rd cutoff of the
pump; this could cause your vehicle
to malfunction.
The capacity of the tank is approxi
mately 15.4 gallons (70 litres).
A filler cap hook is provided on
the inside of the fuel filler flap.
YOUR 406 IN DETAIL
110

29-07-2002
PETROL / LPG DUALFUEL VERSION
166
Filling the LPG tank
(Capacity approximately 46 litres)
– switch off the ignition,
– unscrew the cap protecting thefiller opening,
– lock the filler nozzle onto the opening (if necessary, screw the
appropriate adapter*, located in
the insulated compartment, onto
the filler opening first),
– push the button on the pump,
– once filling has stopped automati cally, unlock the filler nozzle,
– screw the protective cap back onto the filler opening.
* according to destination. Petrol gauge
When the low petrol level indicator
comes on, fill the tank without delay
as the engine can only start using
petrol. Furthermore, a low petrol
level may result in fuel circuit faults.
Gas gauge
If the outside temperature is high,
the gas level indicated by the fuel
gauge may be slightly higher than
the actual level. Safety advice
The safety valve must be
closed before any mainte
nance or repair work is
carried out on your vehicle. To
close it, switch off the ignition.
Ensure that there is no risk that
the loads carried may damage the
tank.
Testing the tank
Decree of 18/01/43 and applica
tion of article 3 of the A.M. of
24/11/82.
The maximum interval between
successive tests is eight years.
However, the test must be repeat
ed whenever the vehicle is sold, if
this sale takes place more than
5 years following the last test.
It is imperative that any work on
the LPG feed system is carried
out by a PEUGEOT dealer.

29-07-2002
In good or rainy weather,
both day and night, the
rear fog lamp is dazzling
and is prohibited.
Do not forget to switch the fog
lamp off when it is no longer need
ed. Front and rear fog
lamps (2nd rotation of
the ring forwards)
These operate with the side lights
and the dipped/main beam head
lamps.
Note: to switch off the rear fog lamp
and the front fog lamps, turn the ring
backwards twice in succession.
Direction indicators
(flashers)
Left:downwards.
Right: upwards.
THE LIGHTS STALK
Front and rear lights
Selection is by turning ring A.
Lights off
Side lights Dipped / main beam
headlamps
Automatic switching
on of lights Dipped/main beam change
Pull the stalk fully towards you.
Note:
with the ignition off, if the dri
ver's door is left open, a buzzer
sounds if you have left your lights on.
Front fog lamps and rear fog
lamp (ring B)
Rotate the ring forwards to switch on
and backwards to switch off. The sta
tus is confirmed by the indicator light
on the instrument panel.
Front fog lamps (first rota
tion of the ring forwards)
These operate with the side lights
and the dipped/main beam head
lamps.
YOUR 406 IN DETAIL
122

29-07-2002
AUTOMATIC SWITCHING ON
OF THE LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off as soon as the light
becomes bright enough or the wind
screen wipers stop.
This function is active when the vehi
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories
position (1st notch),
 Press the end of the lights stalk
for more than two seconds.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. Because of this, the lights do
not come on automatically.
Do not cover the brightness sen
sor connected to the rain sensor,
located in the windscreen behind
the mirror. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting of
the headlamps activated" on the
multifunction display.
Note: Always operate the lighting
controls manually where this is pos
sible.
Disarming
Disarming of the function is accom
panied by an audible signal.
When driving, if this function is
switched off when the headlamps
would switch on in automatic mode,
the lights remain on.
It is however possible to disarm this
function and switch off the lights by:
manually switching off the lights using the lights stalk,
switching off the engine.
YOUR 406 IN DETAIL 123
If the brightness sensor does not
function correctly, the system acti
vates the function (the lights come
on).The driver is alerted by the flash
ing of the ''dipped beam'' warning
light on the instrument panel.
Contact a PEUGEOT dealer to have
the system checked.
Follow me Home
When there is a low level of bright
ness or at night, if you leave your
vehicle, the side lights and the
dipped beam lights may remain on
for approximately one minute.
To do this: place the lights stalk in the AUTO
position,
 place the key in the accessories
position (first notch),
 press the end of the lights stalk for
more than two seconds,
 place the lights stalk in the 0posi
tion,
 flash the headlamps,
 get out of the car and lock it.

29-07-2002
Rear screen wiper
(estate)
Turn ring Ato the first notch,
for intermittent wiping.
Rear screen wash (estate)
Turn ring Abeyond the first
notch; the windscreen wash
then the windscreen wiper
operate for a fixed period.
WINDSCREEN WIPER STALK
Front windscreen wipers
2 Rapid wipe (heavy rain)
1 Normal wipe (moderate rain).
AUTO Automatic wipe
0 Off.
Single wipe (press downwards).
Operation
In position 1or 2, when the vehicle
stops, the windscreen wiper changes
to a lower wiping speed, then
resumes its initial speed when the
vehicle starts again.
When the ignition has been
switched off for more than a
minute with the stalk in the AUTO
position, it is necesary to reacti
vate this function. To do this, move
the stalk to any position, then move it
back to the AUTOposition. Automatic windscreen wiper
In the
AUTO position, the wipers
operate automatically and adjust
their speed to the intensity of the
rainfall.
Operating check
Switching on
Activation of the function is accom
panied by the message 'Automatic
windscreen wiper actuated' on the
multifunction display.
In the event of malfunction in the
AUTO position, the windscreen
wiper will operate in downgrade
mode.
Contact a PEUGEOT dealer to have
the system checked.
YOUR 406 IN DETAIL
124
Do not mask the rain
detector located on the
windscreen behind the
interior mirror.
If you take the vehicle to an auto
matic car wash, switch off the igni
tion or check that the windscreen
wiper stalk is not in the automatic
position.
In Winter, it is advisable to wait for
the windscreen to completely
clear of ice before switching on
the automatic wipe. Windscreen and headlamp wash
Pull the windscreen wiper stalk
towards you.The windscreen wash
then the windscreen wipers operate
for a fixed period.
The windscreen wash and headlamp
wash operate simultaneously for a
few seconds,
only if the dipped
beam or main beam headlamps
are on.

29-07-2002
TRIP COMPUTERDisplay B Display C
– the range,
– the distance travelled,
– the average consumption,
– the current consumption,
– the average speed.
Zero reset
Press the stalk for more than two seconds. Pressing the button on the end of the wiper stalk enables t
he following data to be dis
played:
– the current consumption and the range,
– the average consumption, the distance travelled and theaverage speed calculated over a period "1",
– the average consumption, the distance travelled and the average speed calculated over a period "2".
Periods "1"and "2"are defined by the frequency of the zero
reset. They allow, for instance, daily calculations over period
"1" and monthly calculations over period "2".
Zero reset
When the required period is displayed, press the stalk for
more than two seconds.
YOUR 406 IN DETAIL 137

29-07-2002
Range
The display shows the distance that
can still be covered with the fuel
remaining in the tank.
Note:this figure may rise if there is a
change in driving style or road sur
face, causing a significant drop in
current fuel consumption.
If there are less than 3 litres of fuel in
the tank, only three segments will be
displayed. Average consumption
This is the ratio between the amount
of fuel consumed and the distance
travelled since the computer was last
reset to zero.
The display stops at 30 l/100km.
Current fuel consumption
This gives the fuel consumption
recorded during the last two sec
onds. This function is only displayed
when the vehicle is travelling at more
than 12 m.p.h. (20 km/h).
The display stops at 30 l/100km. Average speed
This is obtained by dividing the dis
tance travelled by the period of time
the vehicle has been in use (with the
ignition on), since the computer was
last reset to zero.Distance travelled
This shows the distance travelled
since the computer was last reset to
zero.
After the trip computer has been
reset to zero, the range data
becomes meaningful only after the
vehicle has been in use for a certain
period.
If horizontal segments are displayed
instead of figures when driving, con
tact a PEUGEOT dealer.
YOUR 406 IN DETAIL
138