2002.5 Peugeot 406 change time

PEUGEOT SERVICING
Your vehicle benefits from extended service intervals.
•For petrol engines: every 20,000 miles (30 000 km) or every two years.
• For direct injection diesel engines: every 12,000 miles (20 000 km) or every two years.
The extension of the service intervals means that the engi ne oil level must be checked regularly: topping up of the
oil between oil changes is normal.
It is for this reason, and for your complete peace of min d, that your Peugeot dealer will carry out a levels check and
topup midway between each routine service, at the time or distance intervals specified.
This will be undertaken free of charge, provided that the maintenance of your vehicle has been carried out within the
PEUGEOT network. At the same time, your Peugeot dealer will offer you a Peugeot safety check, for a nominal fee.
A Peugeot professional will carry out a quick check, and will top up the levels if necessary (oil up to 1 litre, coolant
and screen wash).
The date of the intermediate visit is not shown by the serv ice indicator.
It is to be carried out at least every 10,000 miles (15 0 00 km) for petrol engines and every 6,000 miles (10 000 km) for
direct injection diesel engines.
If the oil level is too low there is a risk of serious d amage to the engine: check the engine oil level at least every
2,000 miles (3 000 km) or 3,000 miles (5 000 km), depen ding on the conditions of use.
The extended service intervals have been made possible by technica l modifications to the vehicles and lubricants:
THUS IT IS ESSENTIALTO ONLY USE ENGINE LUBRICANTS WHICH ARE APPROVED AND REC OMMENDED BY THE
MANUFACTURER
MAINTENANCE OF YOUR 406
18
29-07-2002

29-07-2002
Display BThis enables the following information to be displayed:
– the time,
– the date,
– the outside temperature (the °C symbol flashes when there is a risk of ice),
– the radio displays,
– the status of the doors. The display shows you whether a doo r, the boot or the
bonnet is open and if the fuel filler cap is missing.
– the warning messages (e.g. ''battery low'') or information messa ges (e.g. "top
up fuel tank''), displayed temporarily, can be cleared by pressin g button 1or 2
– the trip computer.
Setting the parameters
Press button 1for two seconds to access the settings. The information flashes
to show it is ready to be modified.
Then, individual presses on button 1 allow you to scroll through the various data
in the following sequence:
– language in which the information is displayed,
– unit of distance (kms or miles),
– unit of temperature (Celsius or Fahrenheit),
– time format (12 then 24 hour mode)
– hour,
– minutes,
– year,
– month,
– day,
Pressing button 2allows you to change the information selected. Maintain the
pressure for rapid scrolling.
After ten seconds without action, the display returns to the ma in screen and the
modified data are recorded.
YOUR 406 IN DETAIL 135

29-07-2002
GENERAL FUNCTIONS
On / offWith the ignition key in the ACCESSORIES or IGNITION position , press button Ato switch the set on or off.
The set can operate for 30 minutes without the vehicle ign ition being switched on.
Antitheft system
The set is coded in such a way that it can operate only on yo ur vehicle. It would not function if fitted to another vehicle.
The antitheft system is automatic and requires no action on your part.
VOLUME SETTING
Adjusting the volume Turn button Ato increase or reduce the volume.
AUDIO SETTINGS Press the "AUDIO" button several times to access the bass (BASS), treble (TREB), loudness (LOUD), fader
(FAD) and balance (BAL).
Exit from audio mode is automatic after a few seconds without p ressing any button, or by pressing the
"AUDIO" button after adjusting the balance.
Note: bass and treble settings are specific to each source. It is possibl e to set them differently for radio, cas
sette or CD changer.
YOUR 406 IN DETAIL
64

29-07-2002
GENERAL FUNCTIONS
On/offWith the ignition key in the ACCESSORIES or IGNITION position , press button Ato switch the set on or off.
The set can operate for 30 minutes without the vehicle ign ition being switched on.
Antitheft system
The audio system is coded in such a way that it can operate on ly on your vehicle. It would not function if fitted to another
vehicle.
The antitheft system is automatic and requires no action on your part.
VOLUME SETTING
Adjusting the volume Turn button Ato increase or decrease the volume.
AUDIO SETTINGS Press the "AUDIO" button several times to access the bass (BASS), treble(TREB), loudness (LOUD), fader
(FAD) , balance (BAL)and automatic volume correction (CAV).
Exit from audio mode is automatic after a few seconds without p ressing any button, or by pressing the
" AUDIO " button after configuration of the automatic volume correction .
Note: bass and treble settings are specific to each source. It is possibl e to set them differently for radio,
cassette or CD changer.
YOUR 406 IN DETAIL
74

29-07-2002
GENERAL FUNCTIONS
On/offWith the ignition key in the ACCESSORIES or IGNITION position , press button Ato switch the set on or off.
The set can operate for 30 minutes without the vehicle ign ition being switched on.
ANTITHEFT SYSTEM
The audio system is coded in such a way that it can operate on ly on your vehicle. It would not function if fitted to another vehicle.
The antitheft system is automatic and requires no action on your part.
VOLUME SETTING
Adjusting the volume
Turn button Ato increase or decrease the volume of the set.
Note: If you have a telephone fitted with a "mute"signal output connected to the set, the set will automati
cally change to " mute" when the telephone is used.
AUDIO SETTINGS Press the "AUDIO" button several times to access the bass (BASS),treble(TREB), loudness (LOUD), fader
(FAD) , balance (BAL)and the automatic volume correction (CAV).
Exit from audio mode is automatic after a few seconds without p ressing any button, or by pressing the
" AUDIO " button after configuration of the automatic volume correction .
Note: the bass and treble settings are specific to each source. It is p ossible to set them differently for radio,
CD, or CD changer.
YOUR 406 IN DETAIL
86

29-07-2002
THE SATELLITE NAVIGATION
SYSTEM
Introduction
The satellite navigation system guides
you to the destination of your choice
by means of vocal and visual instruc
tions.
The heart of the system lies in the use
of a map database and GPS (Global
Positioning System). This enables
your position to be located by means
of several satellites.
The satellite navigation system con
sists of the following components:
the remote control,
the display,
the control unit,
the last voice message recall control,
the CD ROM.
Some functions or services
described in this guide may vary depending on the CD ROM version or the country.The remote control
There is a storage compartment for the remote control in front of the ashtray.
Pointing the remote control at the screen enables the informat ion contained in
the various menus to be selected.
Direction arrows:
These enable you to move around the screen and
thus select a function.
On the welcome screen only, the Up and Down
buttons enable the brightness of the screen to be
adjusted.
menu : this button allows access to the main menu. It can
be used at any time.
esc : escape button
"Short press": cancels the current operation and
returns to the previous screen.
"Press for more than 2 seconds": returns to the
welcome screen.
This button can be used in any menu. It is inactive
during guidance.
mod : mode button
"Short press": changes between date, navigation
and radio.
val : Confirmation button
Confirms the function selected.
YOUR 406 IN DETAIL 95

29-07-2002
Entering a new destination
The last town entered is displayed.
To enter the name of another town, select each letter using
the direction arrows then confirm ("VAL"button) for each
letter.
If an error is made, the "Correct" function enables the last
letter entered to be deleted.
As the name is entered, the "List"function indicates the
number of towns beginning with the same letters. If the li st
contains less than 5 names, these are displayed automat
ically. Select a town then confirm ( "VAL"button).
The "Change" function enables the town entered to be
completely cleared.
When the complete name of the town is displayed, select
the "Validate" function then press the "VAL"button.
Note: following confirmation of a letter, only those letters
which could make up an existing name appear. Enter the name of the street. Select the
"Validate"function
then press the "VAL"button.
Note: the guidance can be activated from the time the
town is entered, without the name of a street or a number.
To do this, select the "Town centre"function.
YOUR 406 IN DETAIL 99
Enter the number in the street. Select the "Validate"func
tion then press the "VAL"button.
Note: the guidance can be activated as soon as the town
and street are entered, without a number. To do this, sele ct
the "Validate" function.

29-07-2002
YOUR 406 IN DETAIL103
Display configuration
From the general menu, the "Configure display"menu
gives access to the following parameters:
Adjustment of the brightness and the video display.
Adjustment of the date and time.
Selection of the language of the display and voice infor mation (English, German, Spanish, French, Italian).
Adjustment of the mode and units. This allows selection of the display in km/h or mph, in degrees Celsius or
Fahrenheit and selection of the time format (12 or 24
hour mode). Navigation options
From the main menu, the
"Navigation options"menu
gives access to the following parameters:
Management of the directories. It enables an address stored under a name to be renamed or deleted. To do
this, select the directory and the name to be changed.
Voice synthesis volume adjustment.
Deletion of all data stored in the two directories.