2002.5 Peugeot 307 SW Dag Owner's Manual

OPENING THE BONNET From inside:push the handle on the
left-hand side under the fascia. From outside: lift the catch and
raise the bonnet. Bonnet strut Secure the strut to hold the bonnet open. Before closing the bonnet, replace the strut in its housing.
To close Lower the bonnet and release it at the end of its travel. Check that thebonnet is properly locked. "Bonnet open" warning With the engine running or the vehicle moving, flashing of the central
"STOP" warning light accompanied by an audible signal and a diagram
on the multi-function display, warnsyou that the bonnet is not properlyclosed. FILLING WITH FUEL Low fuel level
When the minimum fuel level in the tank is rea-ched, this warning lightcomes on.
You can still drive
approximately 50 km.Flashing of the warning light indi- cates a malfunction of the fuelgauge.
Contact a PEUGEOT dealer.The engine must be switched off when filling with fuel.
Open the fuel filler flap.
Insert the key then turn it to theleft.
Remove the cap and hang it onthe hook located on the inside ofthe flap.
A label affixed to the inside of the fuelfiller flap indicates which type of fuelto use. When you fill your tank, do not conti-
nue after the third cut-off of the
pump. This could cause your vehicleto malfunction. The capacity of the tank is approxi- mately 60 litres. After filling the tank, lock the cap and close the fuel filler flap.
YOUR 307 SW IN DETAIL
108
22-07-2002

THE LIGHTS STALK Front and rear lights Selection is by turning ring A.
Lights off Side lights Dipped/Main beam headlamps Automatic switching on of lights Dipped / Main beam change Pull the stalk towards you. Note:
with the ignition off, when the
driver's door is opened, a buzzer sounds if you have left your lights on. Front fog lamps and rear fog lamp Rotate the ring forwards to switch on
and backwards to switch off. The statusis confirmed by the light on the instru-ment panel.
Vehicles fitted with a rear fog lamp (ring B)
Rear fog lamp
This can only operate with the dip-ped / main beam headlamps.
Vehicles fitted with front fog lamps and a rear fog lamp (ring C) Front fog lamps (first rota-tion of the ring forwards). Front and rear foglamps (2nd rotation ofthe ring forwards).
Note: to switch off the rear fog lamp
and the front fog lamps, turn the ringbackwards twice in succession. Direction indicators (flashers)
Left:downwards.
Right: upwards.
YOUR 307 SW IN DETAIL 109
In good or rainy weather, both day and night, thefront and rear fog lampsare dazzling and are pro-hibited.
Do not forget to switch the foglamps off when they are no longerneeded.
22-07-2002

22-07-2002
AUTOMATIC SWITCHING ON OF LIGHTS Side lights and dipped beam head- lamps switch on automatically if the
light is poor, or during operation of
the windscreen wipers. They switch
off when the light becomes brightenough or the windscreen wipersstop. Note:In foggy weather or in snow,
the brightness sensor can detect suf-
ficient light. As a consequence, the
lights will not come on automatically. This function is active when the vehicle is delivered.
To disarm or activate the function: Start with the key in the accesso- ries position (1st notch),
Press the end of the lights stalkfor more than two seconds.
Note: after the ignition is switched off
and depending on the brightness,the lights remain on for approximate-ly 45 seconds or until the vehicle islocked. Do not cover the brightness sen- sor located in the centre of thefascia. It is used for automaticswitching on of the lights. Operating check ActivationActivation of this function is accom- panied by an audible signal and themessage
"Automatic lighting
active" on the multi-function display.
Disarming Disarming of the function is accom- panied by an audible signal. Note: the function is disarmed tem-
porarily when the driver uses the manual lighting controls. If the brightness sensor does not function correctly , the system acti-
vates the function (the lights come
on). The driver is alerted by anaudible signal, accompanied by themessage "Automatic switching on
of lights faulty" on the multi-func-
tion display.
Contact a PEUGEOT dealer to have the system checked.
YOUR 307 SW IN DETAIL
110

22-07-2002
WINDSCREEN WIPER STALK Stalk with intermittent wipe Front windscreen wiper2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe.
0 Off.
Single wipe (press downwards). Stalk with automatic wipeFront windscreen wiper
2 Fast wipe (heavy rain).
1 ormal wipe (moderate rain).
AUTO Automatic wipe.
0 Off.
Single wipe (press downwards). OperationIn position
1or 2, when the vehicle
stops, the windscreen wiper changes to a lower wiping speed, thenresumes its initial speed when thevehicle starts again. In the Intermittent position, the wiping speed is proportional to thespeed of the vehicle. In the AUTOposition, the wiping
speed is proportional to the heavi- ness of the rain. When the ignition has been swit- ched off for more than one minutewith the stalk in the wipe position,it is necesary to reactivate thisfunction. To do this, move the stalk
to any position, then move it back tothe required position.
Windscreen and headlamp wash Pull the windscreen wiper stalk towards you. The windscreen wash then the wind- screen wipers operate for a fixed
period. The windscreen wash andheadlamp wash operate simulta-neously for a few seconds, only if
the dipped beam or main beamheadlamps are on.
YOUR 307 SW IN DETAIL 111

22-07-2002
Maintenance position This position enables the wiper blades to be removed.
In the minute following switching off of the ignition, any action on the stalkpositions the wipers in the centre ofthe windscreen so that they may becleaned or replaced.
To park the wipers after this has been done, switch on the ignitionand operate the stalk.
YOUR 307 SW IN DETAIL
112
Do not cover the rain sen- sor located on the wind-screen behind the interior
mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not in
the automatic position. In winter, itis advisable to wait for the wind-screen to completely clear of icebefore operating the automaticwipe. Rear windscreen wiper
Turn ring Ato the first notch
for intermittent wiping.
Rear windscreen wash Turn ring Apast the first
notch; the windscreen wash then the windscreen wiperoperate for a fixed period. Automatic windscreen wipers In the AUTOposition, the wind-
screen wipers operate automatically and adapt their speed to the intensi-ty of the rainfall.
Operating check ActivationWhen the function is activated, the message "Automatic windscreen
wiping active" appears on the mul-
tifunction display. Disarming Disarming of the function is accom- panied by an audible signal. In the event of malfunction , the dri-
ver is informed by an audible signal and the message "Auto wind-
screen wiper faulty" on the multi-
function display. In the AUTOposition, the wind-
screen wiper will operate in intermit- tent mode.
Contact a PEUGEOT dealer to have the system checked.

22-07-2002
YOUR 307 SW IN DETAIL113
TRIP COMPUTER
Each time the button on the end of the wash/wipe stalk
is pressed, the follo-
wing sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" index with:
¥ range, current consumption and the distance still to be driven,
Ð index "1"(route "1") with:
¥ the distance driven and the ave- rage speed calculated over route "1" ,
Ð index "2"(route "2") with the same
features.
It also permits access to the Excess
Speed Warning function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
- the remaining range
- the distance travelled
- the average consumption
- the current consumption
- the average speed
In addition, it allows access to the war-
ning log information and to the function
Excess speed warning .
Zero reset Press the stalk for more than two seconds.
Colour screen DT
Ð the "Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average coonsumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the Excess
Speed Warning function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.

YOUR 307 SW IN DETAIL
114
Distance remaining to be tra- velled This is the distance remaining to the destination. It can either be calcula-ted by the navigation if guidance is
activated, or entered by the user,minus the distance covered since thedistance was entered. Note:if digits are missing, dashes
are displayed in their place.
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on). The warnings log This summarises the active warning messages by displaying them on themultifunction screen. The excess speed warning function* This monitors the maximum speed required. In the event that the pro-grammed speed is exceeded, themessage "Speed too high" appears
on the multifunction screen, accom-panied by an audible signal. Programming Accelerate to the desired speed. Keep pressing the control to store in
memory.
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note:
this figure may increase if
there is a change in the style of dri- ving or the road surface, producing asignificant drop in the currentconsumption. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer. Current consumption This is the average fuel consumption during the last few seconds. This function is displayed only when the vehicle is travelling at a speedgreater than 30 km/h.
Average consumption This is the average fuel consumption since the computer was last set tozero. Distance travelled This indicates the distance travelled since the computer was last set tozero.
* During the year. Activation Keep pressing the control until the display indiciates
"Excess speed
ON" .
Switching off Keep pressing the control until the display indiciates "Excess speed
OFF" .
The routes The routes "1"and "2"are indepen-
dent but have identical application.Route "1"for example allows you to
make daily calculations and route "2" monthly calculations.
22-07-2002

22-07-2002
YOUR 307 SW IN DETAIL113
TRIP COMPUTER
Each time the button on the end of the wash/wipe stalk
is pressed, the follo-
wing sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" index with:
¥ range, current consumption and the distance still to be driven,
Ð index "1"(route "1") with:
¥ the distance driven and the ave- rage speed calculated over route "1" ,
Ð index "2"(route "2") with the same
features.
It also permits access to the Excess
Speed Warning function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
- the remaining range
- the distance travelled
- the average consumption
- the current consumption
- the average speed
In addition, it allows access to the war-
ning log information and to the function
Excess speed warning .
Zero reset Press the stalk for more than two seconds.
Colour screen DT
Ð the "Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average coonsumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the Excess
Speed Warning function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.