2002.5 Peugeot 307 SW Dag Owner's Manual

22-07-2002
Place the jack 4in contact with
one of the four locating points A
on the sub-frame, the one which is closest to the wheel to bechanged.
Extend the jack 4until its base is
in contact with the ground.Ensure that the centre line of thebase of the jack is straight abovethe locating point A.
Raise the vehicle
Remove one bolt and install thecentralising tool 5in its place.
Unscrew the other bolts andremove the wheel.
PRACTICAL INFORMATION
142

Detach the wheel/holder assem- bly from the rear of the vehicle.
Take out the notched hook torelease the wheel, as shown inthe illustration.
Removing the wheel Slide the holder cover to gain access to the tools.
Place the chock 7under the
wheel diagonally opposite to theone to be changed.
Remove the trim, using thewheelbrace 1, pulling at the
valve passage hole (for vehiclesfitted with steel wheels).
Loosen the wheel bolts (see ¤"Special features of alloywheels" for vehicles fitted withalloy wheels). Note: you can use the other end
of the tool 6to unscrew the
wheel bolts.

22-07-2002
PRACTICAL INFORMATION143
For your safety, always change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- with first or reverse gear enga- ged (position Pfor the automatic
gearbox),
- with the vehicle chocked. Never go underneath a vehicle that is supported only by a jack(use a ramp) Never refit the holder under the vehicle without the sparewheel. After changing the wheel:
- have the correct positioning of the punctured wheel, the tighte- ning of the bolts and the tyrepressure checked by a PEUGEOT dealer as soon aspossible.
- have the punctured tyre repai- red and refit it to the vehicle assoon as possible.
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer. Store the rest of the tools in the right-hand trim of the boot.
Fitting a wheel
Position the wheel using the cen- tralising tool 5to assist you.
Tighten the bolts by hand andremove the centralising tool 5.
Partly tighten the bolts using thewheelbrace 1.
Fold the jack 4and remove it.
Fully tighten the bolts using thewheelbrace 1.
Replace the wheel trim, startingby placing the wheel trim notchopposite the valve, and press iton using the palm of the hand.
Put the corresponding tools in
the holder and secure its cover.
Place the holder on the groundand align the spare wheel on it.
Pass the notched hook into the
holder cover.
Refit the wheel under the vehicletightening the winch control nutusing the wheelbrace 1.
Fully tighten and check that the
wheel is horizontally flush
against the rear floor.
Close the flap using the lug tolock the winch.

22-07-2002
Special features of alloy wheels Bolt coversAlloy wheel bolts are covered by chrome trims. Use tool 6to remove the trims befo-
re slackening the bolts. Fitting the spare wheel If your vehicle is fitted with a steel spare wheel, when fitting it, it is normal
when tightening the bolts, to
notice that the washers do not come
into contact with the rim. The sparewheel is secured by the cone shapeof each bolt. Fitting snow tyres If you fit snow tyres mounted on steel wheels onto your vehicle, it is essen-
tial to use special bolts available
from your PEUGEOT dealer. Anti-theft bolts* If your wheels are fitted with an anti- theft bolt (one per wheel), the chro-me trim and then the plastic covermust be removed using tool
6, befo-
re unscrewing the bolt using one ofthe two anti-theft sockets (whichwere given to you on delivery of yourvehicle along with the duplicate keysand the confidential card) and thewheel brace 1.
Note : make a careful note of the
code number engraved on the head
of the anti-theft socket. This willenable you to obtain duplicate anti-
theft sockets from a PEUGEOT dealer.
* According to model and country
PRACTICAL INFORMATION
144

22-07-2002
CHANGING A BULB Front lights Note: on the right-hand side, remove the style cover, fixed
with two plastic screws, to access the bulbs. Handle the bulbs with a dry cloth.
1 - Dipped beam headlamps (H7-55W).
2 - Main beam headlamps (H1-55W).
3 - Front fog lamps (H1-55 W). Turn the protective cover corresponding to the faulty bulb a quarter of a turn and remove it.
Disconnect the connector.
Press the end of the securing clip to free it. Changethe bulb. When fitting the new bulb, ensure that the direction notches are positioned correctly and the securing clip
is fixed properly.
Reconnect the connector.
Refit the protective cover, positioning it with the arrowupwards, then turn it a quarter of a turn to the right. The headlamps are fitted with polycarbonate glass with aprotective coating.
Do not clean them with a dry or
abrasive cloth, nor with a detergent or solvent pro-duct. Use a sponge and soapy water.
4 - Side lights (W 5 W). Pull the socket rearwards, remove the bulb and change it.
5 - Direction indicators (PY 21 W amber). Turn the bulb holder a quarter of a turn and remove it.
Change the bulb.
Note: In certain climatic conditions (low temperature,
humidity), condensation inside the headlamp glass is
normal ; it disappears a few minutes after the lights are
switched on.
PRACTICAL INFORMATION 145

22-07-2002
Direction indicator side
repeaters (WY 5W amber). Push the repeater forwards and
release the assembly.
Hold the connector and turn thelens a quarter turn.
Change the bulb.
PRACTICAL INFORMATION
146
Amber coloured bulbs
(direction indicators and side repeaters), must bereplaced with bulbs ofidentical specification
and colour.

22-07-2002
PRACTICAL INFORMATION147
Third brake light: 4 W 5 W bulbs. Remove the tailgate upper trim carefully by unclipping it on eitherside, perpendicular to its direc-tion of engagement.
Insert a screwdriver into the twoouter holes Bto press on the two
tabs C.
Push the light unit outwards whilemaintaining the pressure on thetabs.
Pull the light unit outwards whiletilting it.
Change the faulty bulb.
When refitting, ensure that thelight unit tabs are engaged cor-rectly and that the tailgate uppertrim has been put back in place
correctly.
Remove the bulb holder pressing on the tabs A,
Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts. When refitting, take care to position
the bulb holder and the light correctly.
Number plate lights (W 5 W) Insert a thin screwdriver into one of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Change the faulty bulb.
Rear lights
1 - Brake lights (P 21 W).
2 - Side lights (R 5 W).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W), right
side.
Fog lamp (P 21 W), left side.
These 5 bulbs are changed by remo- ving the light: Remove the corresponding boot side trim to access the light,
Remove the light fixing nut insidethe boot,
Remove the light fixing nut outsidethe boot,
Remove the light,
Unclip the harness,

CHANGING A FUSE The fuse boxes are located under the fascia (driver's side) and in theengine compartment. The spare fuses and special pliers A
are fixed to the inside of the lid of the fascia fuse box. Removing and changing a fuse Before changing a fuse you must establish the cause of the fault and
have it corrected. The fuse numbersare indicated on the fuse box. Use the special pliers A.
Always change a faulty fuse for one of the same rating. Fascia fuses
Unscrew the bolt a quarter of a turn with a coin, then pull thehandle to open the cover andaccess the fuses.
PRACTICAL INFORMATION
148
Fuse no. Rating Functions
1 10 A Rear fog lamp.
2 15 A Rear screen wiper.
4 15 A Front electric windows.
5 15 A Left brake light including trailer.
7 20 A Rear courtesy light, front courtesy light, map readers - Lighter - 12 V front socket - Glove box lighting -Concealing flap control.
Correct
PliersAIncorrect
22-07-2002

22-07-2002
Engine compartment fuses Fuse box
To access the fuse box in the engine compartment (next to the battery): unclip the cover.
Carefully close the cover and refit the style cover when you havefinished.
PRACTICAL INFORMATION
150
The electrical system of your vehicle is designedto operate with standardor optional equipment.
Before installing other electricalequipment or accessories on yourvehicle, contact a PEUGEOT
dealer. PEUGEOT will not accept respon- sibility for the cost incurred inrepairing your vehicle or for recti-fying the malfunctions resultingfrom the installation of accesso-ries not supplied and not recom-mended by PEUGEOT and notinstalled in accordance with itsinstructions, in particular wherethe equipment in questionconsumes more than 10 milliam-peres. * The maxi-fuses provide additio- nal protection for the electrical
systems. All work must be carried
out by a PEUGEOT dealer.
Fuse no. Rating Functions 1* 30 A Fan unit.
2* 30 A ESP/ABS pump motor.
3* 30 A ESP/ABSsolenoid valves.
4* 60 A Built-in Systems Interface supply.
5* 70 A Built-in Systems Interface supply.
6* 20 A Heated seats.
7* 30 A Ignition switch, power.
8* 70 A Power steering electro-pump unit.