Page 3352 of 4323
RS11D±01
H24331ClawClip
H24332
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Manual Adjuster Type)
RS±61
3344 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
NOTICE:
If the wiring connector of the SRS is disconnected
and the ignition switch is in the ON or ACC position,
DTCs will be recorded.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1. PRECAUTION (SEE PAGE RS±1 and RS±3)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the 2 seat track covers.
HINT:
Tape the screwdriver tip before use.
4. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the body.
5. REMOVE HEADREST
6. REMOVE SEAT CUSHION OUTER SHIELD
(a) Remove the screw from the seat cushion outer shield.
(b) Using a screwdriver, remove the seat cushion outer
shield.
HINT:
Tape the screwdriver tip before use.
7. REMOVE RECLINING ADJUSTER RELEASE HANDLE
8. REMOVE VERTICAL ADJUSTER HANDLE
(a) Using a screwdriver, remove the vertical adjuster handle
cap.
HINT:
Tape the screwdriver tip before use.
Page 3360 of 4323
H24333
H24331ClawsClip
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Manual Adjuster Type)
RS±69
3352 Author: Date:
2005 SEQUOIA (RM1146U)
6. INSTALL VERTICAL ADJUSTER HANDLE
(a) Install the vertical adjuster handle with the 2 screws.
(b) Install the vertical adjuster handle cap.
7. INSTALL RECLINING ADJUSTER RELEASE HANDLE
8. INSTALL SEAT CUSHION OUTER SHIELD
Install the seat cushion outer shield with the screw.
9. INSTALL HEADREST
10. INSTALL FRONT SEAT
Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the body.
(a) w/ Side airbag:
Connect the airbag connector.
(b) Connect the connectors.
(c) Slide the front seat to the rearmost position.
(d) Tighten the bolts on the front side temporarily, starting
from the bolt on the inner side.
(e) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
(f) Slide the front seat to the foremost position.
(g) Tighten the bolts on the rear side temporarily, starting
from the bolt on the inner side.
(h) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
11. INSTALL SEAT TRACK COVERS
12. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
13. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
14. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)
Page 3362 of 4323
RS11F±01
H23897
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS±71
3354 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
NOTICE:
If the wiring connector of the SRS is disconnected
and the ignition switch is in the ACC or ON position,
DTCs will be recorded.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1. PRECAUTION (SEE PAGE RS±1 and RS±3)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3. REMOVE ROOF HEADLINING (SEE PAGE BO±101)
4. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
(a) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(b) Remove the 13 bolts and the curtain shield airbag assem-
bly.
Page 3364 of 4323
RS11G±01
AB0152
SST
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS±73
3356 Author: Date:
2005 SEQUOIA (RM1146U)
DISPOSAL
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
When scrapping a vehicle equipped with the SRS or dis-
posing of the curtain shield airbag assembly, be sure to
deploy the airbag first in accordance with the procedure
described below. If any abnormality occurs with the airbag
deployment, contact the TOYOTA MOTOR SALES,
U.S.A., INC.
CAUTION:
Never dispose of a curtain shield airbag assembly
which has an undeployed airbag.
The airbag produces an exploding sound when it is
deployed, so perform the operation outdoors and
where it will not create a nuisance to nearby resi-
dents.
When deploying the airbag, always use the specified
SST (SRS Airbag Deployment Tool). Perform the op-
eration in a place away from electrical noise.
When deploying the airbag, perform the operation at
least 10 m (33 ft) away from the curtain shield airbag
assembly.
The curtain shield airbag assembly becomes ex-
tremely hot when the airbag is deployed, so do not
touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a cur-
tain shield airbag assembly with a deployed airbag.
Do not apply water, etc. to a front passenger airbag
assembly with a deployed airbag.
Always wash your hands with water after completing
the operation.
HINT:
Prepare a battery as the power source to deploy the airbag.
Page 3365 of 4323
AB0158
Battery
SST
H23899
SST
R13455
10 m (33 ft) or more
SSTBattery RS±74
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
3357 Author: Date:
2005 SEQUOIA (RM1146U)
1. AIRBAG DEPLOYMENT WHEN SCRAPPING VE-
HICLE
(a) Check the function of the SST (see step 1±(a) on page
RS±23).
SST 09082±00700
(b) Precaution (see page RS±1 and RS±3).
(c) Disconnect the cable from the negative battery terminal.
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
(d) Remove the roof headlining (see page BO±101).
(e) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, be careful not to dam-
age the airbag wire harness.
(f) Install the SST.
(1) Connect the connectors of the SST to the curtain
shield airbag assembly.
SST 09082±00700, 09082±00802 (09082±10801,
09082±20801)
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the ve-
hicle rear side window.
(3) Maintaining enough clearance for the SST wire har-
ness in the rear side window, close all doors and
windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip of the SST to the
negative (±) terminal.
Page 3366 of 4323
AB0158
Battery
SST
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS±75
3358 Author: Date:
2005 SEQUOIA (RM1146U)
(g) Deploy the airbag.
(1) Check that no one is inside the vehicle or within a
10 m (33 ft) radius of the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:
When deploying the airbag, make sure that no one is
near the vehicle.
The curtain shield airbag assembly becomes ex-
tremely hot when the airbag is deployed, so do not
touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a cur-
tain shield airbag assembly with a deployed airbag.
Do not apply water, etc. to a curtain shield airbag as-
sembly with a deployed airbag.
Always wash your hands with water after completing
the operation.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.
2. DEPLOYMENT WHEN DISPOSING OF CURTAIN
SHIELD AIRBAG ASSEMBLY
NOTICE:
When disposing of the curtain shield airbag assem-
bly, never use the customer's vehicle to deploy the
airbag.
Be sure to follow the procedure given below when de-
ploying the airbag.
HINT:
Prepare a battery as the power source to deploy the airbag.
(a) Check the function of the SST (see step 1±(a) on page
RS±23).
(b) Remove the curtain shield airbag assembly (see page
RS±97).
When removing the front passenger airbag assembly,
work must be started 90 seconds after the ignition
switch is turned to the ºLOCKº position and the nega-
tive (±) terminal cable is disconnected from the bat-
tery.
When storing the front passenger airbag assembly,
keep the airbag deployment side facing upward.
Page 3368 of 4323
H23928
SST
H23929
Tires
(5 or more)
H23917
H2467110 m (33 ft) or more SST
Battery Curtain Shied Airbag Assembly
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
RS±77
3360 Author: Date:
2005 SEQUOIA (RM1146U)
(e) Install the SST.
After connecting the SST below to each other, connect
them to the curtain shield airbag assembly.
SST 09082±00802 (09082±10801, 09082±20801)
(f) Place tires.
(1) Place at least 2 tires under the tire which the curtain
shield airbag assembly is tied to.
(2) Place at least 2 tires over the tire which the curtain
shield airbag assembly is tied to. The top tire should
have the disc wheel installed.
NOTICE:
Do not place the SST connector under the tire because it
could be damaged.
(3) Tie the tires together with 2 wire harness.
CAUTION:
Make sure that the wire harness is tight. Looseness in the
wire harness results in the tires coming free due to the
shock when the airbag is deployed.
(g) Install the SST.
Connect the SST connector.
SST 09082±00700
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, se-
cure some slack for the SST wire harness inside the tire.
(h) Deploy the airbag.
(1) Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip of the SST to the
battery negative (±) terminal.
(2) Check that no one is within a 10 m (33 ft) radius of
the tire which the shield airbag assembly is tied to.
Page 3371 of 4323
RS0TH±07
H23897
RS±80
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
3363 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
(a) Install the curtain shield airbag assembly with the 13
bolts.
Torque: 9.8 N´m (100 kgf´cm, 7 ft´lbf)
CAUTION:
Pay attention not to twist the deployment section of the cur-
tain shield airbag assembly.
NOTICE:
If the curtain shield airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the curtain shield
airbag assembly with a new one.
When installing the curtain shield airbag assembly,
take care it is not pinched between other parts.
Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
(b) Connect the connector of the curtain shield airbag as-
sembly.
2. INSTALL ROOF HEADLINING (SEE PAGE BO±108)
3. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
4. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
5. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)
