2001 TOYOTA SEQUOIA electrical

DI±358
± DIAGNOSTICSENGINE
552 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2111 Throttle Actuator Control System
±Stuck Open
DTC P2112 Throttle Actuator Control System
±Stuck Closed
CIRCUIT DESCRIPTION
The throttle motor is operated by the ECM. It opens and closes the throttle valve using gears. The opening
angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body.
The throttle position sensor provides feedback to the ECM to control the throttle motor and set the throttle
valve angle in response to driver input.
HINT:
This Electrical Throttle Control System (ETCS) does not use a throttle cable.
DTC No.DTC Detection ConditionTrouble Area
P2111Throttle motor locked during ECM order to close.
(1 trip detection logic)
Throttle control motor and sensor circuit

Throttle control motor and sensor
P2112Throttle motor locked during ECM order to open.
(1 trip detection logic)
Throttle control motor and sensor

Throttle body

Throttle valve
MONITOR DESCRIPTION
The ECM concludes that there is a malfunction of the ETCS (Electronic Throttle Control System) when the
throttle valve remains at a fixed angle despite high drive current from the ECM. The ECM will turn on the MIL
and a DTC is set.
FAIL SAFE
If the ETCS (Electronic Throttle Control System) has a malfunction, the ECM cuts off current to the throttle
control motor. The throttle control valve returns to a predetermined opening angle (approximately 16°) by
the force of the return spring. The ECM then adjusts the engine output by controlling the fuel infection (inter-
mittent fuel±cut) and ignition timing in accordance with the accelerator pedal opening angle to enable the
vehicle to continue at a minimum speed.
If the accelerator pedal is depressed firmly and slowly, the vehicle can be driven slowly.
If a ºpassº condition is detected and then the ignition switch is turned OFF, the fail±safe operation will stop
and the system will return to normal condition.
DICFA±02

A21430
From BatteryETCS Fuse
+BM
+M
±M
ME01ECM
Motor Control
Circuit Throttle Control Motor
2
1 DI±362
± DIAGNOSTICSENGINE
556 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2118 Throttle Actuator Control Motor Current
Range/Performance
CIRCUIT DESCRIPTION
The Electronic Throttle Control System (ETCS) has a dedicated power supply circuit. The voltage (+BM) is
monitored and when the voltage is low (less than 4V), the ECM concludes that the ETCS has a fault and
current to the throttle control motor is cut.
When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage
is low, the current to the motor is cut. If repairs are made and the system has returned to normal, turn the
ignition switch OFF. The ECM then allows current to flow to the motor and the motor can be restarted.
HINT:
This Electrical Throttle Control System (ETCS) does not use a throttle cable.
DTC No.DTC Detection ConditionTrouble Area
P2118Open in ETCS power source circuit (+BM)

Open in ETCS power source circuit

ETCS fuse

ECM
MONITOR DESCRIPTION
The ECM monitors the battery supply voltage applied to the electronic throttle motor +BM. When the power
supply voltage drops below the threshold, the ECM concludes that the power supply has an open circuit.
The MIL is turned on and a DTC is set.
DICFB±02

A19694A19803
5
3.7 to 4.4
2.9 to 3.6
1.6
1.4
025 IC No. 1
IC No. 2
Accelerator Pedal
Position SensorECM
VPA
EPA
VCPA
VPA2
EPA2
VCP2Usable Range
Magnet
Magnet
Accelerator Pedal Position Sensor Output Voltage (V)
: Accelerator Pedal Fully Released
: Accelerator Pedal Fully DepressedAccelerator Pedal Turning Angle (deg)*
2*1
*1
*2
± DIAGNOSTICSENGINE
DI±371
565 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT DESCRIPTION
HINT:

This electrical throttle control system does not use a throttle cable.

This accelerator pedal position sensor is a non±contact type.
The accelerator pedal position sensor is mounted in the accelerator pedal to detect the angle of the accelera-
tor pedal. This sensor is electronically controlled and uses Hall±effect elements.
In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes
between 0 V and 5 V in proportion to the angle of the accelerator pedal. The VPA is a signal to indicate the
actual accelerator pedal angle and is used for the engine control. VPA2 is used to detect malfunctions of
the sensor itself.
The ECM judges the current angle of the accelerator pedal from these signals input from terminals VPA and
VPA2, and the ECM controls the throttle motor based on these signals.

DIDIM±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±521
715 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
SYSTEM DESCRIPTION
The ECT (Electronic controlled automatic transmission) is an automatic transmission that electronically con-
trols shift timing using the ECM. The ECM detects electrical signals that indicate engine and driving condi-
tions, and controls the shift point, based on driver habits and road conditions. As a result, fuel efficiency and
power transmission performance are improved.
Shift shock has been reduced by controlling the engine and transmission simultaneously.
In addition, the ECT has features such as follows:

Diagnostic function.

Fail±safe function when a malfunction occurs.

DIDIT±01
D11984
DI±542
± DIAGNOSTICSAUTOMATIC TRANSMISSION
736 Author: Date:
2005 SEQUOIA (RM1146U)
MANUAL SHIFTING TEST
1. MANUAL SHIFTING TEST
HINT:

With this test, it can be determined whether the trouble oc-
curs in the electrical circuit or is a mechanical problem in
the transmission.

If any abnormalities are found in the following test, the
problem is in the transmission itself.
(a) Disconnect the connector of the transmission wire.
(b) Drive with the transmission wire disconnected.
Shifting the shift lever to the L, 2, 3, 4 and D position to
check whether the shifting condition changes the table
below.
Shift PositionShifting Condition
L @2No Shift (Not Change)
2 @3Down Shift @Up Shift
3 @4Down Shift @Up Shift
4 @DNo Shift (Not Change)
HINT:
When driving with the transmission wire disconnected, the gear
position will be as follows:

When the shift lever is in the L or the 2 position, the gear
is held in the 1st position.

When the shift lever is in the 3rd position, the gear is held
in the 3rd position.

When the shift lever is in the 4 or the D position, the gear
is held in the 4th position.

When the shift lever is in the R or the P position, the gear
is also in the R or the P position respectively.
(c) Connect the connector of the transmission wire.
(d) Clear the DTC (See page DI±565).

DIDIX±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±553
747 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
If a normal code is displayed during the diagnostic trouble code check although the trouble still occurs, check
the electrical circuits for each symptom in the order given in the charts on the following pages and proceed
to the page given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
1. Chapter 1: Electronic Circuit Matrix Chart
Refer to the table below when the trouble cause is considered to be electrical.
If the instruction ºProceed to next circuit inspection shown on matrix chartº is given in the flow chart
of each circuit, proceed to the circuit with the next highest number in the table to continue the check.
If the trouble still occurs even though there are no abnormalities in any of the other circuits, check and
replace the ECM.
HINT:
*1: When the circuit on which mark *1 is attached is defective, DTC could be output (see page DI±573).
SymptomSuspect AreaSee page
No up±shift
(A particular gear, from 1st to 4th gear, is not up±shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±641
DI±646
IN±35
No up±shift (4th " 5th)
1. O/D main switch circuit
2. Engine coolant temp. sensor circuit *1
3. Speed sensor NT circuit *1
4. Shift solenoid valve (SL1) circuit *1
5. Shift solenoid valve (SL2) circuit *1
6. Shift solenoid valve (SR) circuit *1
7. ECM
DI±688
DI±58
DI±591
DI±603
DI±631
DI±651
IN±35
No up±shift (3rd " 4th)
1. Engine coolant temp. sensor circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±58
DI±646
IN±35
No up±shift (1st " 2nd)
1. Shift position L switch circuit
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±691
DI±646
IN±35
No down±shift (5th " 4th)
1. O/D main switch circuit
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SL2) circuit *1
4. Shift solenoid valve (SR) circuit *1
5. ECM
DI±688
DI±603
DI±631
DI±651
IN±35
No down±shift (2nd " 1st)
1. Shift position L switch circuit
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±691
DI±646
IN±35
No down±shift
(A particular gear, from 1st to 4th gear, is not down±shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±641
DI±646
IN±35
No lock±up
1. ATF temperature sensor circuit *1
2. Stop light switch circuit *1
3. Speed sensor NT circuit *1
4. Shift solenoid valve (SLU) circuit *1
5. Engine coolant temp. sensor circuit *1
6. ECM
DI±582
DI±600
DI±591
DI±680
DI±58
IN±35
No lock±up off4. Shift solenoid valve (SLU) circuit *1
6. ECM
DI±680
IN±35

NORMAL S1 OFF S2 OFF SR OFF
ºRºGear
ºDº
º3º
º2º
ºLº
S1S2Gear GearSR SL1 SL2GearS1 S2 SR SL1 SL2 S1 S2 SR SL1 SL2 S1 S2 SR SL1 SL2
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
""
"
"
"
"
"
"
"
"
RRR R
1 st
1 st
1 st1 st 1 st
1 st 1 st
1 st 1 st 1 st
1 st E/B 1 st E/B 1 st E/B 1 st E/B
2 nd E/B
3 rd E/B
4 th
5 th
3 rd E/B 3 rd E/B2 nd E/B
2 nd
4 th 4 th
5 th 5 th
"
2 nd E/B"
4 th 4 th4 th 4 th 4 th 4 th 3 rd 3 rd3 rd
3 rd 4 th
"
5 th 5 th5 th 4 th
"
3 rd E/B
"
3 rd E/B
3 rd E/B 3 rd E/B
5 th 5 th
2 nd E/B
3 rd E/B
5 th 5 th4 th
3 rd E/B 3 rd E/B
4 th
1 st E/B
"
2 nd
" "
5 th1 st E/B"
2 nd Fail 4th
"
3 rd E/B
3 rd E/B
4 th
5 th3 rd
""
2 nd
2 nd
2 nd
2 nd 2 nd 2 nd 2 nd 2 nd
2 nd
3 rd E/B 3 rd E/B
"
"
"
"
3 rd
3 rd
3 rd 1 st
1 st
1 st1 st 3 rd
4 th
4 th
4 th
4 th
Fail 4 th
"
3 rd 4 th
"
Position
DI±568
± DIAGNOSTICSAUTOMATIC TRANSMISSION
762 Author: Date:
2005 SEQUOIA (RM1146U)
: ON
X: OFF

": Condition in the electrical malfunction is shown on the left of º"º.
Condition in the fail±safe mode is shown on the right of º"º.
E/B: Engine brake.

S2 SR OFF S1 SR OFF S1 S2 SR OFF
Gear Gear Gear
ºRº
ºDº
º3º
º2º
ºLº
"
RRR R
1 st
1 st E/B
4 th
5 th3 rd
2 nd
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
""
"
"
"
"
""
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
1 st
1 st 1 st 1 st 1 st
1 st 1 st 1 st 1 st2 nd
2 nd
2 nd 3 rd
3 rd
3 rd
3 rd 3 rd
3 rd
3 rd
3 rd
1 st E/B
1 st E/B
1 st E/B
1 st E/B
1 st E/B 1 st E/B 1 st E/B
1 st E/B
1 st E/B
1 st E/B 1 st E/B 1 st E/B1 st E/B 1 st E/B
1 st E/B
1 st E/B
1 st E/B
4 th
4 th
4 th
4 th
4 th 4 th
4 th
5 th 4 th4 th
4 th 4 th 4 th
4 th
4 th
3 rd E/B
3 rd E/B3 rd
1 st 1 st 1 st
1 st
1 st1 st
2nd1 st
2nd 2nd 1 st E/B2nd1 st 3 rd E/B
3 rd
3 rd 3 rd E/B
3 rd1 st
3 rd
3 rd E/B
3 rd
1 st
1 st
1 st
1 st
1 st
1 st 1 st
4 th
3 rd
3 rd E/B
3 rd
3 rd E/B
3 rd E/B
4 th
5 th
4 th
5 th
Fail 4 th
Fail 4 th
Fail 4 th
Fail 4 th
""" "
" " " " " " """"
"""" " " "
" " " "
S1 S2 SR SL1 SL2 S1 S2 SR SL1 S1 S2 SR SL1 S1 S2 SR SL1 SL2
3 rd SL2 SL2GearS1 S2 OFF
"
"
"
"
"
"
"
"
3 rd 4 th
"
Position
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±569
763 Author: Date:
2005 SEQUOIA (RM1146U)
: ON
X: OFF

": Condition in the electrical malfunction is shown on the left of º"º.
Condition in the fail±safe mode is shown on the right of º"º.
E/B: Engine brake.