2001 TOYOTA SEQUOIA check engine

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±639
833 Author: Date:
2005 SEQUOIA (RM1146U)
2 Perform active test
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
HINT:
While driving, the shift position can be forcibly changed with the hand±held tester.
Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you
to confirm the problem (See page DI±567).
Standard:
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]

Press º"º button: Shift up

Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
HINT:

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

The 4th to 5th up±shiftings must be performed with the accelerator pedal released.

The 5th to 4th down±shiftings must be performed with the accelerator pedal released.

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the hand±
held tester.
OK:
Gear position changes in accordance with the tester command.
NG Repair or replace valve body

(See page AT±10).
OK

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±659
853 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
LINE PRESS UP *
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]

Vehicle Stopped.

IDL: ON
[HINT]
OFF: Line pressure up (When the active test of ºControl the Line Pres-
sure Upº is performed, the ECM commands the SLT solenoid to turn
off).
ON: No action (normal operation)
±
*: ºLINE PRESS UPº in the ACTIVE TEST is performed to check the line pressure changes by connecting
the SST to the automatic transaxle, which is used in the HYDRAULIC TEST (See page DI±540) as well.
HINT:

The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

Normally, the line pressure detected in the ACTIVE TEST is approximately half of the value detected
in the HYDRAULIC TEST's stall test.

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±667
861 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P2740
(a) and (b) are detected momentarily within 0.5 sec. when
neither P2742 nor P2743 is detected (1±trip detection logic)
(a) ATF temperature sensor No.2 resistance is less than 25 W
(0.046 V)
(b) ATF temperature sensor No.2 resistance is more than 156
kW (4.915 V)
HINT:
Within 0.5 sec. the malfunction switches from (a) to (b) or from
(b) to (a)

Open or short in ATF temperature sensor No.2 circuit

Transmission wire (ATF temperature sensor No.2)

ECM
P2742ATF temperature sensor No.2 resistance is less than 25 W
(0.046 V) for 0.5 sec. or more (1±trip detection logic)
Short in ATF temperature sensor No.2 circuit

Transmission wire (ATF temperature sensor No.2)

ECM
P2743
ATF temperature No.2 sensor resistance is more than 156 kW
(4.915 V) when 15 minutes or more after the engine start
DTC is detected for 0.5 sec. or more (1±trip detection logic)
Open in ATF temperature sensor No.2 circuit

Transmission wire (ATF temperature sensor No.2)

ECM
MONITOR DESCRIPTION
The Automatic Transmission Fluid (ATF) temperature sensor converts ATF temperature to an electrical re-
sistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects
an open or short in the AFT temperature circuit. If the resistance value of the ATF temperature is less than
25 W (0.046 V) or more than 156 kW (4.915 V), the ECM interprets this as a fault in the ATF sensor or wiring.
The ECM will turn on the MIL and store the DTC.
MONITOR STRATEGY
P2740ATF temperature sensor/Range check (Fluttering)
Related DTCsP2742ATF temperature sensor/Range check (Low voltage)Related DTCs
P2743ATF temperature sensor/Range check (High voltage)
Required sensors/ComponentsATF temperature sensor (TFT sensor)
Frequency of operationContinuous
Duration0.5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not present.See page DI±545
Range check (Fluttering, Low voltage)
The typical enabling condition is not avail-
able.±
Range check (High voltage)
Time after engine start15 min. or more±

G23400G23400D14177
Accelerator Pedal
Opening Angle
Lock±up OFF
Lock±up ON
"time Engine Speed
Accelerator Pedal
Fully Released DI±676
± DIAGNOSTICSAUTOMATIC TRANSMISSION
870 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
LOCK UP
[Test Details]
Control the shift solenoid SLU to set the automatic transmission to the
lock±up condition.
[Vehicle Condition]

Throttle valve opening angle: Less than 35 %

Vehicle Speed: 60 km/h (37 mph) or more
Possible to check the SLU opera-
tion.
HINT:

This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.

This test can be conducted in the 5th gear.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
HINT:

When changing the accelerator pedal opening angle while driving, if the engine speed does not
change, lock±up is on.

Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will
close the throttle valve and lock±up may be turned off automatically.)

F16807
GND
F19430
GND
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±719
913 Author: Date:
2005 SEQUOIA (RM1146U) RM+ (S25±20) ±
GND (S25±22)
R±L ± W±B
Height Control
Compressor
Motor Lock (+)Engine idling, vehicle height changes from ºNORMALº to
ºHIGHº by pressing the height control switch (While
height control compressor assy is working).
Below 1.0 V
RM± (S25±21) ±
Body groundBR±Y ± W±B
Height Control
Compressor
Motor Lock (±)
AlwaysBelow 1.0 V
GND (S25±22) ±
Body groundW±B ±
Body groundGroundAlwaysBelow 1.0 V
B (S25±24) ±
GND (S25±22)V ± W±BBatteryIG switch ON10 to 14 V
LO (S25±26) ± PWB
Height Control
I di t ºLOº
Engine idling, vehicle height is ºNORMALº "
P i th ºDOWNº b tt f th h i ht t l it h10 V or more "LO (S25 26)
GND (S25±22)P ± W±BIndicator ºLOº
SignalPressing the ºDOWNº button of the height control switch
turns on the ºLOº indicator lamp (*1)10 V or more "
Below 5 V
STP (S25±27) ± GY WBStop LightBk dld dRl d10 to 14 V "STP (S25 27)
GND (S25±22)G±Y ± W±BSto Light
SwitchBrake pedal depressed " Released10 to 14 V "
Below 1.5 V
SIL (S25±30) ±
GND (S25±22)G±R ± W±BDiagnosis Sig-
nalHand±held tester is connected to DLC3Pulse generation
(See waveform 3)
DOOR (S25±31) ± RWBDSilIG switch ON, each door opened "Below 1.5 VDOOR (S25 31)
GND (S25±22)R ± W±BDoor SignalIG switch ON, each door o ened "
All door closed
Below 1.5 V
10 to 14 V
DNSW (S25±32) ±
GND (S25±22)W ± W±B
Height Control
Switch
ºDOWNº SignalIG switch ON, ºDOWNº button of height control switch
pushed in "
ºDOWNº button of height control switch releasedBelow 1.5 V "
10 to 14 V
BAT (S25±25) ±
GND (S25±22)V ± W±BBatteryAlways10 to 14 V
CANL (S25±28) ±
GND (S25±22)W ± W±BCAN Commu-
nication SignalIG switch ONPulse generation
(See waveform 1)
CANH (S25±29) ±
GND (S25±22)G ± W±BCAN Commu-
nication SignalIG switch ONPulse generation
(See waveform 2)
*1: Perform inspection after checking that the height control indicator lamp switches are illuminated when
the height control switch button is pressed.
Waveform 1 (Reference):
ItemContents
TerminalCANL ± GND
Tool setting1V/DIV, 10ms/DIV
Vehicle conditionIgnition SW ON, Engine stopped
Waveform 2 (Reference):
ItemContents
TerminalCANH ± GND
Tool setting1V/DIV, 10ms/DIV
Vehicle conditionIgnition SW ON, Engine stopped

F19458
DI±750
± DIAGNOSTICSAIR SUSPENSION SYSTEM
944 Author: Date:
2005 SEQUOIA (RM1146U)
2 Inspect AIR SUS relay.
PREPARATION:
Remove the AIR SUS relay from the engine room R/B No. 2.
CHECK:
Check continuity between each terminal of the AIR SUS relay.
OK:
Tester connectionResistance
3 ± 510 kW or higher
3 ± 5
Below 1 W
(When battery voltage is applied to ter-
minals 1±2)
NG Replace AIR SUS relay.
OK

F16805
S25
Suspension Control ECU
Wire Harness View:
RC
F19460
Engine Room R/B No. 2:
AIR SUS
Relay Terminal
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±751
945 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check harness and connector (Engine room R/B ± Suspension control ECU,
Body ground).
PREPARATION:
Disconnect the ECU connector.
CHECK:
Check for an open or short circuit in the harness and the con-
nector between the AIR SUS relay terminal 1 of the engine
room R/B and terminal S25±5 (RC) of the suspension control
ECU.
OK:
There is no open or short in the wire harness.
CHECK:
Check for an open circuit in the harness and the connector be-
tween the AIR SUS relay terminal 2 of the engine room R/B and
body ground.
OK:
There is no open in the wire harness.
NG Repair or replace harness or connector.
OK
Replace suspension control ECU
(See page IN±35).

F19461
Height Control Compressor
Connector Front View:
H13
DI±756
± DIAGNOSTICSAIR SUSPENSION SYSTEM
950 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check harness and connector (Height control compressor ± Battery, Body
ground).
PREPARATION:
(a) Reconnect the ECU connector.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage according to the value(s) in the table be-
low.
OK:
Tester connectionConditionSpecified value
H13±1 ± Body ground
Engine idling, height con-
trol switch is pushed from
ºNº to ºUPº
10 to 14 V
HINT:
Measure the voltage within 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified value
H13±2 ± Body groundAlwaysBelow 1 W
NG Repair or replace harness or connector.
OK
Replace suspension control ECU
(See page IN±35).