2001 TOYOTA SEQUOIA fuse

DI±292
± DIAGNOSTICSENGINE
486 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0560 System Voltage
MONITOR DESCRIPTION
The battery supplies electricity to the ECM even when the ignition switch is OFF. This electricity allows the
ECM to store data such as DTC history, freeze frame data, fuel trim values, and other data.
If the battery voltage falls below a minimum level, the ECM will conclude that there is a fault in the power
supply circuit. The next time the engine starts, the ECM will turn on the MIL and a DTC will be set.
DTC No.DTC Detecting ConditionTrouble Area
P0560Open in back up power source circuit

Open in back±up power source circuit

EFI fuse

ECM
HINT:
If DTC P0560 present, the ECM will not store another DTC.
MONITOR STRATEGY
Related DTCsP0560System voltage malfunction
Required sensors/componentsECM
Frequency of operationContinuous
Duration3 sec.
MIL operationImmediate (*1)
Sequence of operationNone
*1: The DTC is set immediate. The MIL will be illuminated after the engine starts in the next time.
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Stand±by RAMInitialized
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Battery voltageLess than 3.5 V
DICF7±02

A21381
Engine Room J/B
EFI No. 1 Fuse
B17411
BATT (+) E6
E4
E1(±)
DI±294
± DIAGNOSTICSENGINE
488 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check EFI No. 1 fuse of engine room J/B.
PREPARATION:
Remove the EFI No. 1 fuse from the engine room J/B.
CHECK:
Check the resistance of the EFI No. 1 fuse.
OK:
Standard: Below 1 W
NG Check for short in all harness and components
connected to EFI No. 1 fuse.
OK
3 Check voltage between terminal BATT and E1 of ECM connector.
CHECK:
Measure the voltage between terminals of the E6 and E4 ECM
connector.
OK:
Standard:
Tester ConnectionSpecified Condition
BATT (E4±3) ± E1 (E6±1)9 to 14 V
OK Check for intermittent problems
(See page DI±11).
NG

A21381
Engine Room J/B
EFI No. 1 Fuse
B17417
E4
BATT ECM Connector
± DIAGNOSTICSENGINE
DI±295
489 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check for open and short in harness and connector between ECM and EFI No. 1
fuse, EFI No. 1 fuse and battery.
PREPARATION:
(a) Remove the EFI No. 1 fuse from the engine room J/B.
(b) Disconnect the E4 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tor.
OK:
Standard:
Tester ConnectionSpecified Condition
Engine Room J/B (EFI No. 1 fuse
terminal 2) ± BATT (E4±3)Below 1 W
Engine Room J/B (EFI No. 1 fuse
terminal 2) or BATT (E4±3) ±
Body ground
10 kW or higher
NG Repair or replace harness or connector.
OK
5 Check the battery (See page CH±1).
NG Replace battery.
OK
Check and replace engine room J/B.

A21430
From BatteryETCS Fuse
+BM
+M
±M
ME01ECM
Motor Control
Circuit Throttle Control Motor
2
1 DI±362
± DIAGNOSTICSENGINE
556 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2118 Throttle Actuator Control Motor Current
Range/Performance
CIRCUIT DESCRIPTION
The Electronic Throttle Control System (ETCS) has a dedicated power supply circuit. The voltage (+BM) is
monitored and when the voltage is low (less than 4V), the ECM concludes that the ETCS has a fault and
current to the throttle control motor is cut.
When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage
is low, the current to the motor is cut. If repairs are made and the system has returned to normal, turn the
ignition switch OFF. The ECM then allows current to flow to the motor and the motor can be restarted.
HINT:
This Electrical Throttle Control System (ETCS) does not use a throttle cable.
DTC No.DTC Detection ConditionTrouble Area
P2118Open in ETCS power source circuit (+BM)

Open in ETCS power source circuit

ETCS fuse

ECM
MONITOR DESCRIPTION
The ECM monitors the battery supply voltage applied to the electronic throttle motor +BM. When the power
supply voltage drops below the threshold, the ECM concludes that the power supply has an open circuit.
The MIL is turned on and a DTC is set.
DICFB±02

A21380
Engine Room J/B
ETCS
Fuse
B17411
+BM (+) E6
E4
E1 (±)
± DIAGNOSTICSENGINE
DI±365
559 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check ETCS fuse.
PREPARATION:
Remove the ETCS fuse from the engine room J/B.
CHECK:
Check the resistance of the ETCS fuse.
OK:
Below 1 W
NG Check for short in all harness and components
connected to ETCS fuse.
OK
2 Check voltage between terminal +BM and E1 of ECM connector.
CHECK:
Measure the voltage between the specified terminals of the E6
and E4 ECM connector.
OK:
Standard:
Tester ConnectionSpecified Condition
+BM (E4±7) ± E6 (E6±1)9 to 14 V
OK Check for intermittent problems
(See page DI±11).
NG

A21380
Engine Room J/B
ETCS
Fuse
B17417
E4
+BM
DI±366
± DIAGNOSTICSENGINE
560 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check for open or short in harness or connector between battery and ETCS fuse,
ETCS fuse and ECM.
PREPARATION:
(a) Remove the ETCS fuse from the engine room J/B.
(b) Disconnect the E4 ECM connector.
CHECK:
Measure the resistance of the wire harness side connector be-
tween the ETCS fuse and ECM.
OK:
Standard:
Tester ConnectionSpecified Condition
Engine Room J/B (ETCS fuse
terminal) ± +BM (E4±7)Below 1 W
Engine Room J/B (ETCS fuse
terminal) or +BM (E4±7) ±
Body ground
10 kW or higher
PREPARATION:
(a) Remove the ETCS fuse from the engine room J/B.
(b) Disconnect the battery positive terminal.
CHECK:
Measure the resistance of the wire harness side connector be-
tween the ETCS fuse and battery.
OK:
Standard:
Tester ConnectionSpecified Condition
Engine Room J/B (ETCS fuse
terminal) ± Battery positive terminalBelow 1 W
Engine Room J/B (ETCS fuse
terminal) or
Battery positive terminal ± Body ground
10 kW or higher
NG Repair or replace harness or connector.
OK
Check engine room J/B.

± DIAGNOSTICSENGINE
DI±379
573 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check whether DTC output recurs (DTC P2120, P2122, P2123, P2125, P2127,
P2128 or P2138)
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Disconnect the battery terminals or remove the EFI No. 1 fuse and ETCS fuse (Clear DTCs).
(c) Start the engine.
(d) Drive the engine at idle for 15 seconds or more.
(e) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / PENDING CODES.
CHECK:
Read the DTC output.
RESULT:
Display (DTC Output)Proceed To
P2120, P2122, P2123,P2125, P2127, P2128 or P2138A
No outputB
B System is OK.
A
Replace ECM (See page SF±80).

A23659
Wire Harness Side:
HT
A38
Sensor 1A/F Sensor Connector
AF+
Front ViewAF±
+B A39
B17415A55007
E7ECM Connector
HA1A
A1A+
A1A±
A2A+
A2A±HA2A
A23512
Reference (Bank 1 Sensor 1 System Drawing):
A/F Sensor A/F Relay
Heater
Sensor
A1A+ HA1A
Duty
Control ECM
From
Battery
A/F Heater
Fuse
A1A±
To EFI Relay DI±398
± DIAGNOSTICSENGINE
592 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check for open and short in harness and connector between ECM and A/F sen-
sor.
PREPARATION:
(a) Disconnect the A38 or A39 A/F sensor connector.
(b) Turn the ignition switch to ON.
CHECK:
(a) Measure the voltage between the +B terminal of the A/F
sensor connector and body ground.
Standard:
Tester ConnectionsSpecified Conditions
+B (2) ± Body groundBetween 9 V and 14 V
PREPARATION:
(a) Turn the ignition switch to OFF.
(b) Disconnect the E7 ECM connector.
CHECK:
(a) Check the resistance.
Standard (Check for open):
Tester ConnectionsSpecified Conditions
HT (A38±1) ± HA1A (E7±2)
HT (A39±1) ± HA2A (E7±1)Below 1 W
AF+ (A38±3) ± A1A+ (E7±22)
AF+ (A39±3) ± A2A+ (E7±23)Below 1 W
AF± (A38±4) ± A1A± (E7±30)
AF± (A39±4) ± A2A± (E7±31)Below 1 W
Standard (Check for short):
Tester ConnectionsSpecified Conditions
HT (A38±1) or HA1A (E7±2) ± Body ground
HT (A39±1) or HA2A (E7±1) ± Body ground10 kW or higher
AF+ (A38±3) or A1A+ (E7±22) ± Body ground
AF+ (A39±3) or A2A+ (E7±23) ± Body ground10 kW or higher
AF± (A38±4) or A1A± (E7±30) ± Body ground
AF± (A39±4) or A2A± (E7±31) ± Body ground10 kW or higher