Page 201 of 4323
B17430
HA1A
A1A+
A1A±
HA2A
A2A+
A2A±
HT1B
OXIB
HT2B
OX2B
E2
PRG
ACIS
AIV1
AIV2
THA
E2G
VG
E2
THW
PPMP
VPMP
MPMP#10
#20
#30
#40
#50
#60
#70
#80
IGT1
IGT2
IGT3
IGT4
IGT5
IGT6
IGT7
IGT8
IGF1
IGF2 To A/F Relay
A/F Sensor
(Bank 1 Sensor 1)
A/F Sensor
(Bank 2 Sensor 1)
HO2 Sensor
(Bank 1 Sensor 2)
HO2 Sensor
(Bank 2 Sensor 2) To EFI Relay
To EFI No.2
Fuse
VSV (EVAP)
VSV (ACIS)
VSV (AI Control)
VSV (AI Control)
Mass Air Flow
Meter
ETC Sensor
Pump Modul
Pressure
Sensor
Control
Valve To VC
TerminalTo Battery
IGN2
Fuel Injector #1
Fuel Injector #2
Fuel Injector #3
Fuel Injector #4
Fuel Injector #5
Fuel Injector #6
Fuel Injector #7
Fuel Injector #8
Ignition Coil and
Igniter No.1
Ignition Coil and
Igniter No.2
Ignition Coil and
Igniter No.3
Ignition Coil and
Igniter No.4
Ignition Coil and
Igniter No.5
Ignition Coil and
Igniter No.6
Ignition Coil and
Igniter No.7
Ignition Coil and
Igniter No.8
± DIAGNOSTICSENGINE
DI±7
201 Author: Date:
2005 SEQUOIA (RM1146U)
Page 207 of 4323
± DIAGNOSTICSENGINE
DI±13
207 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check air filter.
PREPARATION:
Remove the air filter.
CHECK:
Visual check that the air filter is not excessively dirty or oily.
NG Repair or replace
air filter.
OK
5 Check idle speed (See page EM±11).
NG Proceed to problem symptoms table on page
DI±33.
OK
6 Check fuel pressure (See page SF±7).
NG Proceed to page SF±7 and continue to trouble-
shoot.
OK
7 Check for spark (See page IG±1).
NG Proceed to page IG±1 and continue to trouble-
shoot.
OK
Proceed to problem symptoms table on page
DI±33.
Page 250 of 4323
DI±56
± DIAGNOSTICSENGINE
250 Author: Date:
2005 SEQUOIA (RM1146U) VVT CTRL B1
Turn on and off OCV
(Oil Control Valve)ON/OFF
Engine stalls or idles roughly
when OCV turned ON
Normal engine running or idling
when OCV off
VVT CTRL B2Turn on and off OCV
(Oil Control Valve)ON/OFF
Engine stalls or idles roughly
when OCV turned ON
Normal engine running or idling
when OCV off
A/C CUT SIGControl A/C cut signalON/OFF±
FUEL PUMP/SPDActivate fuel pump (C/OPN Relay)ON/OFF±
TC/TE1Turn on and off TC and TE1 con-
nectionON/OFFON: TC and TE1 connected
OFF: TC and TE1 disconnected
FC IDL PROHBTProhibit idling fuel cut controlON/OFF±
ETCS OPEN SLOWThrottle actuatorON: throttle valve opens slowly
This test is possible when the fol-
lowing conditions are met:
Ignition switch ON
Engine does not start
Fully depressing accelerator ped-
al (APP: 58 degrees or more)
ETCS CLOSE SLOWThrottle actuatorON: throttle valve closes slowlySame as above
ETCS OPEN FASTThrottle actuatorON: throttle valve opens fastSame as above
ETCS CLOSE FASTThrottle actuatorON: throttle valve closes fastSame as above
FUEL CUT #1Cylinder #1 injector fuel cutON/OFFThis test is possible during vehicle
stopping and engine idling.
FUEL CUT #2Cylinder #2 injector fuel cutON/OFFSame as above
FUEL CUT #3Cylinder #3 injector fuel cutON/OFFSame as above
FUEL CUT #4Cylinder #4 injector fuel cutON/OFFSame as above
FUEL CUT #5Cylinder #5 injector fuel cutON/OFFSame as above
FUEL CUT #6Cylinder #6 injector fuel cutON/OFFSame as above
FUEL CUT #7Cylinder #7 injector fuel cutON/OFFSame as above
FUEL CUT #8Cylinder #8 injector fuel cutON/OFFSame as above
VENT VALVE (ALONE)Activate vent valve
(built into pump module)ON/OFF±
VCUUM PUMPActivate vacuum pump
(built into pump module)ON/OFF±
Page 259 of 4323
± DIAGNOSTICSENGINE
DI±65
259 Author: Date:
2005 SEQUOIA (RM1146U)P0351
(DI±221)
Ignition Coil ºAº Primary/Second-
ary Circuit
Open or short in IGF 1 and IGT 1 circuit from No. 1 ignition coil
with igniter to ECM
No. 1 ignition coil with igniter
Ignition system
ECM
P0352
(DI±221)Ignition Coil ºBº Primary/Second-
ary Circuit
Open or short in IGF 2 and IGT 2 circuit from No. 2 ignition coil
with igniter to ECM
No. 2 ignition coil with igniter
Ignition system
ECM
P0353
(DI±221)Ignition Coil ºCº Primary/Second-
ary Circuit
Open or short in IGF 2 and IGT 3 circuit from No. 3 ignition
coil with igniter to ECM
No. 3 ignition coil with igniter
Ignition system
ECM
P0354
(DI±221)Ignition Coil ºDº Primary/Second-
ary Circuit
Open or short in IGF 1 and IGT 4 circuit from No. 4 ignition coil
with igniter to ECM
No. 4 ignition coil with igniter
Ignition system
ECM
P0355
(DI±221)Ignition Coil ºEº Primary/Second-
ary Circuit
Open or short in IGF 2 and IGT 5 circuit from No. 5 ignition coil
with igniter to ECM
No. 5 ignition coil with igniter
Ignition system
ECM
P0356
(DI±221)Ignition Coil ºFº Primary/Second-
ary Circuit
Open or short in IGF 1 and IGT 6 circuit from No. 6 ignition coil
with igniter to ECM
No. 6 ignition coil with igniter
Ignition system
ECM
P0357
(DI±221)Ignition Coil ºGº Primary/Second-
ary Circuit
Open or short in IGF 1 and IGT 7 circuit from No. 7 ignition coil
with igniter to ECM
No. 7 ignition coil with igniter
Ignition system
ECM
P0358
(DI±221)Ignition Coil ºHº Primary/Second-
ary Circuit
Open or short in IGF 2 and IGT 8 circuit from No. 8 ignition coil
with igniter to ECM
No. 8 ignition coil with igniter
Ignition system
ECM
P0412
(DI±234)Air Injection System Air Switch-
ing Valve Malfunction
Open in air switching valve drive circuit
Short between air switching valve circuit and +B circuit
Air injection driver
ECM
P0418
(DI±242)Air Injection System Air Pump
Malfunction
Open in air pump drive circuit
Short between air pump circuit and +B circuit
Air injection driver
ECM
P0420
(DI±249)Catalyst System Efficiency Be-
low Threshold (Bank 1)Gas leakage on exhaust system
Heated oxygen sensor (bank 1 sensor 1, 2)
Three±way catalytic converter
P0430
(DI±249)Catalyst System Efficiency Be-
low Threshold (Bank 2)Gas leakage on exhaust system
Heated oxygen sensor (bank 2 sensor 1, 2)
Three±way catalytic converter
Page 267 of 4323
DID82±01
A20891
Mass Air Flow Sensor Crankshaft Position Sensor
Actual Valve TimingCorrection Target Valve Timing
Feedback
Duty Control ECM
Camshaft Timing
Oil Control
Valve (OCV)
Vehicle Speed Signal Engine Coolant Temp. Sensor Throttle Position Sensor
Camshaft Position Sensor
± DIAGNOSTICSENGINE
DI±73
267 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
DTC P0010 Camshaft Position ºAº Actuator circuit
(Bank 1)
DTC P0020 Camshaft Position ºAº Actuator circuit
(Bank 2)
CIRCUIT DESCRIPTION
The Variable Valve Timing (VVT) system includes the ECM, the Oil Control Valve (OCV) and the VVT control-
ler. The ECM sends a target ºduty±cycleº control signal to the OCV. This control signal, applied to the OCV,
regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on en-
gine operation conditions such as intake air volume, throttle position and engine coolant temperature.
The ECM controls the OCV, based on the signals output from the sensors. The VVT controller regulates the
intake camshaft angle using oil pressure through the OCV. As a result, the relative position between the cam-
shaft and the crankshaft is optimized, and the engine torque improves, fuel economy improves, and exhaust
emissions decrease under overall driving conditions. Also, the ECM detects the actual valve timing using
signals from the camshaft position sensor and the crankshaft position sensor, and performs feedback con-
trol. This is how target valve timing is verified by the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P0010
P0020Open or short in OCV circuit
Open or short in OCV circuit
OCV
ECM
Page 268 of 4323
DI±74
± DIAGNOSTICSENGINE
268 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR DESCRIPTION
After the ECM sends the ºtargetº duty±cycle signal to the OCV (Oil Control Valve), the ECM monitors the
OCV current to establish an ºactualº duty±cycle. When the actual duty±cycle ratio varies from the target
duty±cycle, the ECM sets a DTC.
MONITOR STRATEGY
RltdDTCP0010VVT oil control valve bank 1 range checkRelated DTCsP0020VVT oil control valve bank 2 range check
Required sensors/componentsOCV
Frequency of operationContinuous
Duration1 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Battery voltage11 V13 V
Target duty ratio±70%
StarterOFF
Current cut statusNot cut
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Either of the following conditions is met:Condition 1 or 2
1. Output signal duty for OCVOutput duty ratio is 100% (always ON) but target duty ratio is less than 70%
2. Output signal duty for OCVOutput duty is 3% or less despite the ECM supplying current to the OCV
COMPONENT OPERATING RANGE
ParameterStandard Value
Output signal duty for OCVºMore than 3%º and ºless than 100%º
Page 273 of 4323
± DIAGNOSTICSENGINE
DI±79
273 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0011 Camshaft Position ºAº ±Timing Over±
Actuator or System Performance (Bank 1)
DTC P0012 Camshaft Position ºAº ±Timing Over±
Retarded (Bank 1)
DTC P0021 Camshaft Position ºAº ±Timing Over±
Actuator or System Performance (Bank 2)
DTC P0022 Camshaft Position ºAº ±Timing Over±
Retarded (Bank 2)
CIRCUIT DESCRIPTION
Refer to DTCs P0010 on page DI±73.
DTC No.DTC Detecting ConditionTrouble Area
P0011
P0021
Advanced cam timing:
After engine is warmed up and engine speed is at 400 to
4,000 rpm, condition (a) continues. (1 trip detection logic)
(a) Valve timing does not change from current valve timing
Valve timing
OCV
P0012
P0022
Retarded cam timing:
After engine is warmed up and engine speed is at 400 to
4,000 rpm, condition (a) continues. (2 trip detection logic)
(a) Valve timing does not change from current valve timing
OCV
VVT controller assembly
ECM
MONITOR DESCRIPTION
The ECM optimizes the valve timing using the VVT (Variable Valve Timing) system to control the intake valve
camshaft. The VVT system includes the ECM, the OCV (Oil Control Valve) and the VVT controller. The ECM
sends a target ºduty±cycleº control signal to the OCV. This control signal, applied to the OCV, regulates the
oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake valve cam-
shaft.
Example:
A DTC will set if: 1) the difference between the target and actual valve timing is more than 5 degrees of the
crankshaft angle (CA) and the condition continues for more than 4.5 sec.; or 2) the OCV is forcibly activated
63 times or more.
Advanced cam DTCs are subject to º1 tripº detection logic.
Retarded cam DTCs are subject to º2 tripº detection logic.
DIAON±02
Page 275 of 4323
± DIAGNOSTICSENGINE
DI±81
275 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check operation of OCV.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and warm it up.
(c) Turn the ignition switch to ON and turn the hand±held tester ON.
CHECK:
(a) Select the item: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1 or VVT CTRL B2.
(b) Using the hand±held tester, operate the OCV and check the engine speed.
OK:
Standard:
Tester OperationSpecified Condition
OCV is OFFNormal engine speed
OCV is ONRough idle or engine stall
OK VVT system is OK.*
*: DTC P0011, P0012, P0021 or P0022 is also output when a
foreign object is detected in some parts of the system in the en-
gine oil, and then the system returns to normal in a short time.
As ECM is controlled to eject a foreign object, there is no prob-
lem on the VVT. There is also no problem on the VVT as the oil
filter should catch the foreign object in the engine oil.
NG
2 Check valve timing (See page EM±23).
NG Adjust valve timing.
OK
