2001 TOYOTA SEQUOIA brake light

I21525
Free Pushed in
D14167
ECM:
E8E7E6E5E4
STP(+)
DI±602
± DIAGNOSTICSAUTOMATIC TRANSMISSION
796 Author: Date:
2005 SEQUOIA (RM1146U)
2 Inspect stop light switch.
PREPARATION:
Remove the stop lamp switch assy.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Switch positionTester ConnectionSpecified Condition
Switch pin free1 ± 4Below 1 W
Switch pin pushed in=10 kW or higher
Switch pin free2 ± 310 kW or higher
Switch pin pushed in=Below 1 W
NG Replace stop light switch (See page BR±8).
OK
3 Check harness and connector (ECM ± stop light switch).
PREPARATION:
Install the stop lamp switch assy.
CHECK:
Measure the voltage according to the value(s) in the table be-
low when the brake pedal is depressed and released.
OK:
ConditionTester ConnectionSpecified Condition
Brake pedal is depressedE4 ± 15 (STP) ±
Body ground10 to 14 V
Brake pedal is released=Below 1 V
NG Repair or replace the harness or connector
(See page IN±35).
OK
Replace the ECM (See page SF±80).

C00083
DLC3
CG TC
TS
F16800
Height
Control
Manual
Indicator
Lamp
DI±712
± DIAGNOSTICSAIR SUSPENSION SYSTEM
906 Author: Date:
2005 SEQUOIA (RM1146U)

The TS terminal circuit uses CAN (Controller Area Net-
work) for communication. Therefore, if there are any mal-
functions in the communication circuit, one or more DTCs
in the CAN communication system is/are output.
(6) Set each of the check items to the condition shown
under Operation (B) in the test mode table below.
HINT:
When checking each item, the height control manual indicator
lamp comes on for 1 second.
Test mode table:
Check ItemOperation (A)Operation (B)
Stop light switch signalOFF (Brake pedal not depressed)ON (Brake pedal depressed)
Door courtesy light switch signalON (Each door opened)OFF (All doors closed)
Height control switch signal±Press the height control switch ºUPº first and
then press ºDOWNº
Height control mode select switch signalOFF (Height control mode select switch not
pushed in)ON to OFF (Height control mode select switch
pushed in and released)
(7) Using SST, connect the 3rd terminal of the SST
check wire to terminal TC of the DLC3.
SST 09843±18040
(8) Read the number of blinks of the height control
manual indicator lamp.

± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±715
909 Author: Date:
2005 SEQUOIA (RM1146U)
Test mode (input signal check) table:
Check ItemOperation (A)Operation (B)
Stop light switch signalOFF (Brake pedal not depressed)ON (Brake pedal depressed)
Door courtesy light switch signalON (Each door opened)OFF (All doors closed)
Height control switch signal±Press the height control switch ºUPº first and
then press ºDOWNº
Height control mode select switch signalOFF (Height control mode select switch not
pushed in)ON to OFF (Height control mode select switch
pushed in and released)
HINT:
In step (6), all signals can be checked together.
(7) Read the test mode DTCs by following the prompts
on the tester screen.
HINT:
Refer to the hand±held tester operator's manual for further de-
tails.
(8) Check the malfunction using the code table below.
DTC of air suspension system test mode (input signal check) function:
If a trouble code is displayed during the test mode DTC check, check the circuit listed for that code. For details
of each code, refer to ºSee pageº under the respective DTC No. in the chart.
DTC No.
(See Page)Detection ItemTrouble Area
C1782/82
(DI±767)Stop light switch circuit malfunction

Stop light switch assy

Stop light switch circuit

Suspension control ECU
C1783/83
(DI±770)Door courtesy switch circuit malfunction

Door courtesy light switch assy

W/ Motor back door assy

Door courtesy light switch circuit

Body ECU

Back door ECU

Suspension control ECU
C1786/86
(DI±774)Height control switch circuit malfunction

Height control switch

Height control switch circuit

Suspension control ECU
C1788/88
(DI±778)Height control mode select switch circuit malfunction

Height control mode select switch

Height control mode select switch circuit

Suspension control ECU
(9) After completing the test mode, disconnect the tes-
ter and turn the ignition switch off.

F16807
GND
F19430
GND
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±719
913 Author: Date:
2005 SEQUOIA (RM1146U) RM+ (S25±20) ±
GND (S25±22)
R±L ± W±B
Height Control
Compressor
Motor Lock (+)Engine idling, vehicle height changes from ºNORMALº to
ºHIGHº by pressing the height control switch (While
height control compressor assy is working).
Below 1.0 V
RM± (S25±21) ±
Body groundBR±Y ± W±B
Height Control
Compressor
Motor Lock (±)
AlwaysBelow 1.0 V
GND (S25±22) ±
Body groundW±B ±
Body groundGroundAlwaysBelow 1.0 V
B (S25±24) ±
GND (S25±22)V ± W±BBatteryIG switch ON10 to 14 V
LO (S25±26) ± PWB
Height Control
I di t ºLOº
Engine idling, vehicle height is ºNORMALº "
P i th ºDOWNº b tt f th h i ht t l it h10 V or more "LO (S25 26)
GND (S25±22)P ± W±BIndicator ºLOº
SignalPressing the ºDOWNº button of the height control switch
turns on the ºLOº indicator lamp (*1)10 V or more "
Below 5 V
STP (S25±27) ± GY WBStop LightBk dld dRl d10 to 14 V "STP (S25 27)
GND (S25±22)G±Y ± W±BSto Light
SwitchBrake pedal depressed " Released10 to 14 V "
Below 1.5 V
SIL (S25±30) ±
GND (S25±22)G±R ± W±BDiagnosis Sig-
nalHand±held tester is connected to DLC3Pulse generation
(See waveform 3)
DOOR (S25±31) ± RWBDSilIG switch ON, each door opened "Below 1.5 VDOOR (S25 31)
GND (S25±22)R ± W±BDoor SignalIG switch ON, each door o ened "
All door closed
Below 1.5 V
10 to 14 V
DNSW (S25±32) ±
GND (S25±22)W ± W±B
Height Control
Switch
ºDOWNº SignalIG switch ON, ºDOWNº button of height control switch
pushed in "
ºDOWNº button of height control switch releasedBelow 1.5 V "
10 to 14 V
BAT (S25±25) ±
GND (S25±22)V ± W±BBatteryAlways10 to 14 V
CANL (S25±28) ±
GND (S25±22)W ± W±BCAN Commu-
nication SignalIG switch ONPulse generation
(See waveform 1)
CANH (S25±29) ±
GND (S25±22)G ± W±BCAN Commu-
nication SignalIG switch ONPulse generation
(See waveform 2)
*1: Perform inspection after checking that the height control indicator lamp switches are illuminated when
the height control switch button is pressed.
Waveform 1 (Reference):
ItemContents
TerminalCANL ± GND
Tool setting1V/DIV, 10ms/DIV
Vehicle conditionIgnition SW ON, Engine stopped
Waveform 2 (Reference):
ItemContents
TerminalCANH ± GND
Tool setting1V/DIV, 10ms/DIV
Vehicle conditionIgnition SW ON, Engine stopped

DIDDE±01
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±727
921 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
By accessing the DATA LIST displayed by the hand±held tester, you can read the value of the switches and
sensors and so on without removing any parts. Reading the DATA LIST is the first step of troubleshooting
and is one method to shorten labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Following the display on the tester, read the DATA LIST.
AIR SUSPENSION:
ItemMeasurement Item / Range (Dis-
play)Normal ConditionDiagnostic Note
VEHICLE SPD
Vehicle speed reading / min.: 0
km/h (0 mph), max.: 255 km/h
(158 mph)
Actual vehicle speedSpeed indicated on the combina-
tion meter
FR WHEEL SPD
Wheel speed (Front right) reading /
min.: 0 km/h (0 mph), max.: 255
km/h (159 mph)
Actual vehicle speedSpeed indicated on the speedome-
ter
FL WHEEL SPD
Wheel speed (Front left) reading /
min.: 0 km/h (0 mph), max.: 255
km/h (159 mph)
Actual vehicle speedSpeed indicated on the speedome-
ter
IG VOLTAGEECU power supply voltage / min.:
0 V, max.: 25.5 VActual ECU power supply voltage:
10 to 14 V±
POWER VOLTAGE+B power source voltage / min.: 0
V, max.: 25.5 VActual battery power supply volt-
age: 10 to 14 V±
STEERING ANG
Steering angle sensor reading /
min.: ±49150.5 deg, max.: 49152
degActual steering angle /
Left turn: reading increases
Right turn: reading increasesZero point is set at the point when
battery is connected
ENGINE SPDCrankshaft position sensor read-
ing / min.: 0 rpm, max.: 25,500 rpmActual engine speedSpeed indicated on the combina-
tion meter
HEIGHT SW DOWNHeight control switch (DOWN) /
ON or OFFON: Height control switch
ºDOWNº button pressed
OFF: ±
±
HEIGHT SW UPHeight control switch (UP) / ON or
OFFON: Height control switch ºUPº
button pressed
OFF: ±
±
HEIGHT SW HOLDHeight control mode select switch
/ ON or OFFON: Height control mode select
switch pressed
OFF: ±
±
STOP LIGHT SWStop light switch / ON or OFFON: Brake pedal depressed
OFF: Brake pedal released±
DOOR SWDoor courtesy light switch / ON or
OFFON: Open each door
OFF: Close all doors±
L4 SW4LO switch / ON or OFFON: 2WD/4HI switch pressed
OFF: ±±
TSTS terminal / ON or OFFON: During test mode
OFF: Normal mode±
TCTC terminal / ON or OFFON: DTC recorded
OFF: No DTC recorded±
SOL SLRLHeight control valve solenoid (Lev-
elling solenoid valve) / ON or OFFON: Leveling solenoid operated
OFF: Leveling solenoid not oper-
ated
±
SOL SLRGHeight control valve solenoid
(Gate solenoid valve) / ON or OFFON: Gate solenoid operated
OFF: Gate solenoid not operated±

F19446
W
41G±Y1
4A11
4AG±Y27
S25 STP
BatteryB ALT
85 W 1
1L STOP 2
1FS14
Stop Light Switch
Sub J/B No. 4Suspension Control
ECU
Instrument Panel J/BF10
Fusible Link Block
1L
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±767
961 Author: Date:
2005 SEQUOIA (RM1146U)
DTC C1782/82 Stop Light Switch Circuit (Test Diagnosis)
CIRCUIT DESCRIPTION
When the brake pedal is depressed, the stop light comes on and the signal is input to the STP terminal of
the suspension control ECU.
HINT:
This DTC is output only when the sensor signal check is done.
DTC No.DTC Detecting ConditionTrouble Area
C1782/82The signal from the stop light switch assy does not change.

Stop light switch assy

Stop light switch circuit

Suspension control ECU
WIRING DIAGRAM
DIDE7±01

F16805
Wire Harness View:
S25
STP
DI±768
± DIAGNOSTICSAIR SUSPENSION SYSTEM
962 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Inspect stop light.
CHECK:
Check that the stop light comes on when the brake pedal is depressed and goes off when the brake pedal
is released.
OK:
Stop light operates normally.
NG Go to step 3.
OK
2 Inspect suspension control ECU.
PREPARATION:
Disconnect the ECU connector.
CHECK:
Measure the voltage between terminal S25±27 (STP) of the
suspension control ECU and body ground when the stop light
switch is ON and OFF.
OK:
Switch conditionSpecified condition
Brake pedal depressed (ON)10 to 14 V
Brake pedal released (OFF)Below 1 V
NG Repair or replace harness connector.
OK
Replace suspension control ECU
(See page IN±35).

I21525
Free Pushed in
F16805
Wire Harness View:
S25
STP
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±769
963 Author: Date:
2005 SEQUOIA (RM1146U)
3 Inspect stop light switch assy.
PREPARATION:
Disconnect the stop light switch assy connector.
CHECK:
Check resistance between terminals 1 and 4 of the stop light
switch assy.
OK:
Switch conditionTester connectionSpecified condition
Switch pin free1 ± 4Below 1 W
Switch pin pushed in1 ± 410 kW or higher
NG Replace stop light switch assy.
OK
4 Inspect suspension control ECU.
PREPARATION:
Disconnect the ECU connector.
CHECK:
Measure the voltage between terminal S25±27 (STP) of the
suspension control ECU and body ground when the stop lamp
switch is ON and OFF.
OK:
Switch conditionSpecified condition
Brake pedal depressed (ON)10 to 14 V
Brake pedal released (OFF)Below 1 V
NG Repair or replace harness connector.
OK
Replace suspension control ECU
(See page IN±35).