2001 TOYOTA SEQUOIA engine

+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Case 1
Case 2
Case 3
Case 4
Output voltage of A/F sensor
(sensor 1: front sensor)
Injection volume
Output voltage
Output voltage of heated oxygen
sensor (sensor 2: rear sensor)Mainly suspected
trouble area
OK
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
Sensor 1: front sensor
(sensor 1, heater, sensor 1
circuit)
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NGExtremely rich or lean actual
air±fuel ratio
(Injector, fuel pressure, gas
leakage in exhaust system,
etc.) OK
OK
OK
Almost
no reaction
'
Sensor 2: rear sensor
(sensor 2, heater, sensor 2
circuit)
Almost
no reactionAlmost
no reactionAlmost
no reaction
DI±156
± DIAGNOSTICSENGINE
350 Author: Date:
2005 SEQUOIA (RM1146U)
The following A/F CONTROL procedure enables the technician to check and graph the voltage output of
the heated oxygen sensors.
For displaying the graph indication, first enter ºACTIVE TEST / A/F CONTROL / USER DATA,º then select
ºA/F B1,2S1and O2S B1,2S2º by pressing ºYESº button, and push ºENTERº button before pressing ºF4º
button.
HINT:

If different DTCs that are related to different system are output simultaneously while terminal E2 is used
as a ground terminal, terminal E2 may be open.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. when
a malfunction occurred.

± DIAGNOSTICSENGINE
DI±157
351 Author: Date:
2005 SEQUOIA (RM1146U)
1 Read output DTC.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
P0138, P0158A
P0137, P0157B
P0136, P0156C
HINT:
If any other codes besides P0136, P0137, P0138, P0156, P0157 and/or P0158 are output, perform the trou-
bleshooting for those DTCs first.
B Go to step 14.
C Go to step 7.
A
2 Check output voltage of heated oxygen sensor.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) After warming up the engine, run the engine at 2,500 rpm for 3 minutes.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / O2S B1S2 or B2S2.
(d) Allow the engine to idle.
CHECK:
Read the Heated Oxygen (HO2) sensor output voltage while idling.
RESULT:
HO2 Sensor Output VoltagesProceed To
More than 1.2 VA
Less than 1.0 VB
B Go to step 5.
A

B17416HT1BECM Connector
E7OX1B E8
HT2B
OX2B
A21341
+B
OX E1HT
H2
H4
Components Side:
Bank 1 Sensor 2, Bank 2 Sensor 2
DI±158
± DIAGNOSTICSENGINE
352 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check for short in harness and connector between terminal OX1B and HT1B,
OX2B and HT2B of ECM.
PREPARATION:
(a) Turn the ignition switch to OFF and wait for 5 minutes.
(b) Disconnect the E7 and E8 ECM connector.
CHECK:
(a) Check the resistance.
OK:
Standard:
Tester ConnectionsSpecified Conditions
HT1B (E8±1) ± OX1B (E8±18)10 kW or higher
HT2B (E7±5) ± OX2B (E5±33)10 kW or higher
OK Replace ECM (See page SF±80
NG
4 Check resistance of heated oxygen sensor heater.
PREPARATION:
Disconnect the heated oxygen sensor connector.
CHECK:
Measure resistance between terminals of the heated oxygen
sensor.
OK:
Standard:
Tester ConnectionSpecified Condition
HT (1) ± +B (2)11 to 16 W at 20°C (68°F)
+B (2) ± OX (3)10 kW or higher
NG Replace heated oxygen sensor.
OK
Repair or replace harness or connector.
5 Perform confirmation driving pattern.
NEXT

± DIAGNOSTICSENGINE
DI±159
353 Author: Date:
2005 SEQUOIA (RM1146U)
6 Check whether DTC output recurs (DTC P0138, P0158)
CHECK:
(a) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
(b) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P0138 or P0158A
No outputB
B Check for intermittent problems
(See page DI±11).
A
Replace heated oxygen sensor.
7 Check output voltage of heated oxygen sensor.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Start the engine.
(d) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / O2S B1S2.
(e) After warming up the engine, run the engine at an engine speed of 2,500 rpm for 3 minutes.
CHECK:
(a) Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.
HINT:
Quickly accelerate the engine to 4,000 rpm 3 times using the accelerator pedal.
Standard: Fluctuates between 0.4 V or less and 0.5 V or more.
NG Go to step 14.
OK
8 Perform confirmation driving pattern.
NEXT

DI±160
± DIAGNOSTICSENGINE
354 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check whether DTC output recurs (DTC P0136, P0156)
CHECK:
(a) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / PENDING CODES.
(b) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P0136 or P0156A
No outputB
B Check for intermittent problems
(See page DI±11).
A
10 Replace heated oxygen sensor.
NEXT
11 Perform confirmation driving pattern.
NEXT
12 Check whether DTC output recurs (DTC P0136, P0156)
CHECK:
(a) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / PENDING CODES.
(b) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P0136 or P0156A
No outputB
B Repair completed.
A

B17391
+12 %
Normal Malfunction±12 %
0 V 3.3 V
1 VA/F Sensor Output
HO2 Sensor OutputInjection Volume
Malfunction
± DIAGNOSTICSENGINE
DI±161
355 Author: Date:
2005 SEQUOIA (RM1146U)
13 Perform active test (injection volume).
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and turn the tester ON.
(c) Warm up the engine.
(d) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / INJ VOL.
CHECK:
(a) Change the fuel injection volume using the tester, monitoring the voltage output of Air±Fuel Ratio (A/F)
and HO2 sensors displayed on the tester.
HINT:

Change the fuel injection volume within the range of ±12 % and +12 %. The injection volume can be
changed in 1 % graduations within the range.

The A/F sensor is displayed as AFS B1S1 (AFS B2S1), and the HO2 sensor is displayed as O2S B1S2
(O2S B2S2), on hand±held testers.
RESULT:
Tester Display (Sensor)Voltage VariationsProceed To
AFS B1S1 (AFS B2S1) (A/F)Alternates between more and less than 3.3 VOK
AFS B1S1 (AFS B2S1) (A/F)Remains at more than 3.3 VNG
AFS B1S1 (AFS B2S1) (A/F)Remains at less than 3.3 VNG
HINT:
A normal HO2 sensor voltage (O2S B1S2 (O2S B2S2)) reacts in accordance with increases and decreases
in fuel injection volumes. When the A/F sensor voltage remains at either less or more than 3.3 V despite the
HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.
NG Replace air±fuel ratio (A/F) sensor.
OK

A21341
+B
OX E1HT
H2
H4
Components Side:
Bank 1 Sensor 2, Bank 2 Sensor 2
DI±162
± DIAGNOSTICSENGINE
356 Author: Date:
2005 SEQUOIA (RM1146U)
check and repair extremely rich or lean actu-
arial air fuel ratio (injector, fuel pressure, gas
leakages from exhaust system, etc.)
14 Check for exhaust gas leakage.
CHECK:
Check for exhaust gas leakage from the exhaust manifold and pipe.
OK:
No exhaust gas leakage.
NG Repair or replace exhaust gas leakage point.
OK
15 Inspect heated oxygen sensor.
PREPARATION:
Disconnect the HO2 sensor connector.
CHECK:
Measure the resistance between the terminals of the HO2 sen-
sor connector.
OK:
Standard:
Tester ConnectionsSpecified Conditions
HT (2) ± +B (1)11 to 16 W at 20C (68F)
HT (2) ± E (3)10 kW or higher
NG Replace heated oxygen sensor.
OK

A19288
EFI Relay
± DIAGNOSTICSENGINE
DI±163
357 Author: Date:
2005 SEQUOIA (RM1146U)
16 Check EFI relay.
PREPARATION:
Remove the EFI relay from the engine room J/B.
CHECK:
Inspect the EFI relay.
OK:
Standard:
Terminal No.ConditionSpecified Condition
3 ± 5Always10 KW or higher
3 ± 5Apply B+ between
terminals 1 and 2Below 1 W
NG Replace EFI relay.
OK