2001 TOYOTA SEQUOIA set clock

A23316
Hold
SST
A23317
Turn
SST
A23318
SST
Tension
Turn
A23319
SST
Turn
± ENGINE MECHANICALTIMING BELT
EM±25
2604 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:
Set the SST so that the claw comes in contact with the camshaft
timing pulley bolt, and tighten the lock nut of the SST.
12. INSTALL RH CAMSHAFT TIMING PULLEY
(a) Align the camshaft timing tube knock pin with the knock
pin groove of the timing pulley.
(b) Temporarily install the 4 bolts of the camshaft timing
pulley.
(c) Hold the camshaft timing pulley with SST, and tighten the
pulley bolt.
SST 09960±10010 (09962±01000, 09963±01000)
Torque: 8.1 N´m (83 kgf´cm, 72 in.´lbf)
13. CONNECT TIMING BELT TO LH CAMSHAFT TIMING
PULLEY
(a) Remove any oil or water on the timing pulley, and keep it
clean.
NOTICE:
Only wipe the pulleys; do not use any cleansing agent.
(b) Using SST, turn the timing pulley. Align the installation
mark on the timing belt with the timing mark of the timing
pulley, and hang the timing belt on the timing pulley.
SST 09960±10010 (09962±01000, 09963±01000)
(c) Using SST, turn the LH camshaft timing pulley counter-
clockwise until there is tension between the crankshaft
timing pulley and LH camshaft timing pulley.
SST 09960±10010 (09962±01000, 09963±01000)
14. CONNECT TIMING BELT TO RH CAMSHAFT TIMING
PULLEY
(a) Remove any oil or water on the camshaft timing pulley
and water pump pulley, and keep them clean.
NOTICE:
Only wipe the pulleys; do not use any cleansing agent.
(b) Using SST, turn the timing pulley. Align the installation
mark on the timing belt with the timing mark of the timing
pulley, and hang the timing belt on the timing pulley.
SST 09960±10010 (09962±01000, 09963±01000)

P20636
1.27 mm
Hexagon Wrench
A04454
1.27 mm
Hexagon Wrench
A23307Turn
A23308
A23306
SST
EM±26
± ENGINE MECHANICALTIMING BELT
2605 Author: Date:
2005 SEQUOIA (RM1146U)
15. SET TIMING BELT TENSIONER
(a) Using a press, slowly press in the push rod using 981 ±
9,807 N (100 ± 1,000 kgf, 220 ± 2,205 lbf) of pressure.
(b) Align the holes of the push rod and housing, and pass a
1.27 mm hexagon wrench through the holes to keep the
setting position of the push rod.
(c) Remove the belt tensioner from the press.
(d) Install the dust boot to the belt tensioner.
16. INSTALL TIMING BELT TENSIONER
(a) Temporarily install the belt tensioner with the 2 bolts.
(b) Alternately tighten the 2 bolts.
Torque: 26 N´m (270 kgf´cm, 19 ft´lbf)
(c) Using pliers, remove the 1.27 mm hexagon wrench from
the belt tensioner.
17. CHECK VALVE TIMING
(a) Temporarily install the crankshaft pulley bolt.
(b) Slowly turn the crankshaft pulley 2 revolutions from the
TDC to TDC.
NOTICE:
Always turn the crankshaft pulley clockwise.
(c) Check that each pulley aligns with the timing marks as
shown in the illustration.
If the timing marks do not align, remove the timing belt and rein-
stall it.
18. TIGHTEN CRANKSHAFT PULLEY BOLT
Using SST, install the pulley bolt.
SST 09213±70011 (90119±08216), 09330±00021
Torque: 245 N´m (2,500 kgf´cm, 181 ft´lbf)

A23342
10 mm Hexagon
Wrench
A14399
Timing Mark
Crankshaft
Pulley Bolt
Turn
Idler Pulley Bolt
A23354
B02636
Seal Packing EM±64
± ENGINE MECHANICALCYLINDER HEAD
2643 Author: Date:
2005 SEQUOIA (RM1146U)
(e) Align the camshaft knock pin with the knock pin groove of
the timing tube, and push the timing tube by hand until you
it touches the bottom.
(f) Using a 10 mm hexagon wrench, install the bolt.
Torque: 78 N´m (790 kgf´cm, 58 ft´lbf)
(g) Install the seal washer and screw plug.
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
8. INSTALL CAMSHAFTS
NOTICE:
Since the thrust clearance of the camshaft is small, the
camshaft must be kept level while it is being installed. If the
camshaft is not kept level, the portion of the cylinder head
receiving the shaft thrust may crack or be damaged, caus-
ing the camshaft to seize or break. To avoid this, the follow-
ing steps should be carried out.
(a) Set the crankshaft pulley position.
Turn the pulley clockwise or counterclockwise, and align
the timing mark of the crankshaft pulley with the centers
of the crankshaft pulley bolt and idler pulley bolt.
NOTICE:
Having the crankshaft pulley at the wrong angle can cause
the piston head and valve head to come into contact with
each other when you install the camshaft, causing dam-
age. So always set the crankshaft pulley at the correct
angle.
(b) Install the LH camshafts.
(1) Apply MP grease to the thrust portion of the intake
and exhaust camshafts.
(2) Align the timing marks (2±dot mark) of the camshaft
drive and driven main gears, and place the intake
and exhaust camshafts.
(3) Apply seal packing to the camshaft housing plug.

Remove the old packing material (FIPG).

Apply seal packing to the housing plug.
Seal packing: Part No. 08826±00080 or equivalent

AT5436
SST
AT13H±01
AT5437
Hold
Turn
Free
Lock
Q04237
AT±30
± AUTOMATIC TRANSMISSION (A750E, A750F)TORQUE CONVERTER CLUTCH AND DRIVE PLATE
2938 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE CONVERTER CLUTCH
AND DRIVE PLATE
INSPECTION
1. INSPECT ONE±WAY CLUTCH
(a) Install SST so that it fits in the notch of the converter hub
and outer race of the one±way clutch.
SST 09350±30020 (09351±32020)
(b) Press on the serrations of the stator with a finger and ro-
tate it.
(c) Check if it rotates smoothly when turned clockwise and
locks when turned counterclockwise.
If necessary, clean the converter clutch and retest the one±way
clutch.
Replace the converter clutch if the clutch still fails the test.
2. MEASURE DRIVE PLATE RUNOUT AND INSPECT
RING GEAR
(a) Set up a dial indicator and measure the drive plate runout.
Maximum runout: 0.20 mm (0.0079 in.)
(b) Check for damage to the ring gear.
If runout is not within the specification or if the ring gear is dam-
aged, replace the drive plate. If installing a new drive plate, note
the orientation of the spacers and tighten the bolts (See page
EM±83 or EM±95).

BE2MO±01
I08152
N14863
3 12
53
15
2
I1535121
I1535221
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE±69
3473 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT REAR DOOR POWER WINDOW SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
UP2 ± 3, 4 ± 5Continuity
OFF2 ± 3 ± 5Continuity
DOWN2 ± 4, 3 ± 5Continuity
If continuity is not as specified, replace the switch.
2. INSPECT POWER WINDOW SWITCH CIRCUIT
(Driver 's Door: See page DI±1788)
(Passenger 's Door: See page DI±1826)
(Rear Door: See page DI±1747)
(Back Door: See page DI±1747)
3. INSPECT POWER MAIN RELAY CONTINUITY
ConditionTester connectionSpecified condition
Always1 ± 2Continuity
Always3 ± 5No continuity
Apply B+ between
terminals 1 and 2.3 ± 5Continuity
If continuity is not as specified, replace the relay.
4. Driver 's Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the power window mo-
tor.
NOTICE:
Since the jam protection may not work properly, be sure to
conduct procedures described in ºHOW TO RESET POW-
ER MOTOR (RESET AND PULSE SWITCH)º after this in-
spection.

I05476
2
1
I054772
1
I153572
1
I153582
1
I15353
2
1
BE±70
± BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
3474 Author: Date:
2005 SEQUOIA (RM1146U)
5. Passenger 's Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the power window mo-
tor.
NOTICE:
Since the jam protection may not work properly, be sure to
conduct procedures described in ºHOW TO RESET POW-
ER MOTOR (RESET AND PULSE SWITCH)º after this in-
spection.
6. Rear Right Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminals 2, and check that
the motor turns clockwise.
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the power window mo-
tor.
7. Rear Left Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2, and check that
the motor turns clockwise.

05_SEQUOIA_U (L/O 0408)
39
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
1. To open the fuel filler door, pull the
lever.
When refueling, turn off the engine.
CAUTION

Do not smoke, cause sparks or al-
low open flames when refueling.
The fumes are flammable.

When opening the cap, do not re-
move the cap quickly. In hot weath-
er, fuel under pressure could cause
injury by spraying out of the filler
neck if the cap is suddenly re-
moved.
2. To remove the fuel tank cap, turn
the cap counterclockwise by 90 de-
grees (to the pressure point 1), and
then turn it an additional 30 degrees
(to point 2). Pause slightly before
removing it.
It is not unusual to hear a slight swoosh
when the cap is opened.3. The removed cap can be stored on
the back side of the fuel filler door.
Position the cap so that the hooks point
to the left and right, and set it in the
receptacle on the back side of the door.

05_SEQUOIA_U (L/O 0408)
215
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Compact disc player
Use this button to skip up or down to a
different track.
Push ª
º or ªº side of the ªSEEK/
TRACKº button until the number of the
track you want to listen to appears on the
display. If you want to return to the begin-
ning of the current track, quickly push the
down side of the button one time.
Vehicles with rear seat entertainment sys-
temÐ
While the DVD player is in operation, the
chapter or track can be changed by push-
ing the ª
º or ªº side of the ªSEEK/
TRACKº button.
ST (Stereo reception) display
Your radio automatically changes to stereo
reception when a stereo broadcast is re-
ceived. ªSTº appears on the display. If the
signal becomes weak, the radio reduces
the amount of channel separation to prev-
ent the weak signal from creating noise.
If the signal becomes extremely weak, the
radio switches from stereo to mono recep-
tion.
TA P E
Push the ªTAPEº button to play a cassette
tape.TEXT
This button is used to change the display
for the compact disc that contains text
data.
To change the display, quickly push and
release the ªTEXTº button while the com-
pact disc is playing. The display changes
in the order from the elapsed time to disc
title to track title, then back to the
elapsed time.
If this button is pushed while a compact
disc that does not contain text data is
playing, ªNO TITLEº will appear on the
display.
If the entire disc or track title does not
appear on the display, push and hold the
button until you hear a beep. The rest of
the title will appear.
TUNE (Tuning)
Turn the ªTUNEº knob clockwise to step
up the frequency. Turn the knob counter-
clockwise to step down the frequency.