2001 TOYOTA SEQUOIA ABS

IN±46
± INTRODUCTIONTERMS
46 Author: Date:
2005 SEQUOIA (RM1146U) IAC
Idle Air ControlIdle Speed Control (ISC)
IATIntake Air TemperatureIntake or Inlet Air Temperature
ICMIgnition Control Module±
IFIIndirect Fuel InjectionIndirect Injection (IDL)
IFSInertia Fuel±Shutoff±
ISCIdle Speed Control±
KSKnock SensorKnock Sensor
MAFMass AirflowAir Flow Meter
MAPManifold Absolute PressureManifold Pressure Intake Vacuum
MCMixture Control
Electric Bleed Air Control Valve (EBCV)
Mixture Control Valve (MCV)
Electric Air Control Valve (EACV)
MDPManifold Differential Pressure±
MFIMultiport Fuel InjectionElectronic Fuel Injection (EFI)
MILMalfunction Indicator LampCheck Engine Lamp
MSTManifold Surface Temperature±
MVZManifold Vacuum Zone±
NVRAMNon±Volatile Random Access Memory±
O2SOxygen SensorOxygen Sensor, O2 Sensor (O2S)
OBDOn±Board DiagnosticOn±Board Diagnostic System (OBD)
OCOxidation Catalytic ConverterOxidation Catalyst Convert (OC), CCo
OLOpen LoopOpen Loop
PAIRPulsed Secondary Air InjectionAir Suction (AS)
PCMPowertrain Control Module±
PNPPark/Neutral Position±
PROMProgrammable Read Only Memory±
PSPPower Steering Pressure±
PTOXPeriodic Trap OxidizerDiesel Particulate Filter (DPF)
Diesel Particulate Trap (DPT)
RAMRandom Access MemoryRandom Access Memory (RAM)
RMRelay Module±
ROMRead Only MemoryRead Only Memory (ROM)
RPMEngine SpeedEngine Speed
SCSuperchargerSupercharger
SCBSupercharger BypassE±ABV
SFISequential Multiport Fuel InjectionElectronic Fuel Injection (EFI), Sequential Injection
SPLSmoke Puff Limiter±
SRIService Reminder Indicator±
SRTSystem Readiness Test±
STScan Tool±
TBThrottle BodyThrottle Body
TBIThrottle Body Fuel InjectionSingle Point Injection
Central Fuel Injection (Ci)
TCTurbochargerTurbocharger
TCCTorque Converter ClutchTorque Converter
TCMTransmission Control ModuleTransmission ECU, ECT ECU

SS1KF±04
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS±39
181 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
TIRE PRESSURE MONITOR RECEIVER
Tire pressure monitor receiver set bolt7.57666 in.´lbf
TIRE PRESSURE MONITOR VALVE
Tire pressure monitor valve set nut4.04135 in.´lbf
FRONT AXLE
Hub nut11 01,15083
Tie rod end lock nut5556041
Steering knuckle x Brake caliper8082059
Steering knuckle x Dust cover1231,25090
Drive shaft lock nut1818513
Upper suspension arm x Upper ball joint2352,400173
Brake line clamp x Steering knuckle1051,10077
ABS speed sensor x Steering knuckle2828521
ABS speed sensor wire harness clamp x Steering knuckle8.08271 in.´lbf
ABS speed sensor wire harness clamp x Upper suspension arm8.08271 in.´lbf
FRONT DIFFERENTIAL
Drive pinion x companion flangeSee page SA±43
Differential front mounting cushion x Chassis frame1371,400101
Differential rear mounting cushion x Chassis frame8789064
Differential front mounting cushion x Differential1571,60011 6
Differential rear mounting cushion x Differential1081,10080
Ring gear x Differential case9798571
Differential carrier x Differential tube7880058
Differential carrier x Side bearing retainer6970051
Differential x Front propeller shaft7475054
A.D.D. clutch case x Differential7880058
A.D.D. clutch case x Differential tube7880058
A.D.D. actuator x A.D.D. clutch case2121015
Tube with wire harness assembly clamp x Differential carrier131309
Drain plug6566048
Filler plug3940029
FRONT SUSPENSION
Suspension support x Chassis frame6465047
Piston rod x Suspension support2525018
Lower suspension arm x Shock absorber1351,400100
Upper suspension arm x Chassis frame981,00072
Lower suspension arm x Chassis frame1301,32596
Lower suspension arm x Lower ball joint1591,62111 7
Power steering gear Left side nut
Center bolt
Right side bolt and nut130
165
1651,350
1,700
1,70096
122
122
Tie rod end x Lower ball joint9193067
No. 1, No. 2 spring bumper31 (23)315 (235)23 (17)
Lower suspension arm x Stabilizer bar link6970051

SS±40
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
182 Author: Date:
2005 SEQUOIA (RM1146U) Stabilizer bar x Stabilizer bar link
1919014
Stabilizer bar bracket x Chassis frame3737727
( ) For use with SST
Part tightenedN´mkgf´cmft´lbf
REAR AXLE
Hub nut11 01,12283
Backing plate x Brake caliper1051,07077
Parking brake cable x Backing plate8.08271 in.´lbf
Axle housing x Backing plate1221,24490
Brake line union nut15.515811
ABS speed sensor x Axle housing8.08271 in.´lbf
REAR DIFFERENTIAL
Differential x Propeller shaft7475056
Drive pinion x Companion flangeSee page SA±113
Companion flange x Stud bolt101027.4
Differential carrier x Axle housing7374054
Differential carrier x Bearing cap11 31,15083
Differential case x Ring gear1251,27092
Drain plug4950036
Filler plug4950036
REAR SUSPENSION
Shock absorber x Chassis frame5859143
Shock absorber x Axle housing8788764
REAR LATERAL CONTROL ROD
Lateral control rod x Chassis frame1401,428103
Lateral control rod x Axle housing1301,32696
REAR UPPER AND LOWER CONTROL ARM
Upper control arm x Chassis frame1401,428103
Upper control arm x Axle housing1401,428103
Upper control arm x Brake line bracket2828621
Lower control arm x Chassis frame1301,32696
Lower control arm x Axle housing1301,32696
Lower control arm x Parking brake cable bracket2626519
REAR STABILIZER BAR
Bracket x Axle housing3737727
Stabilizer bar link x Chassis frame6970451
Stabilizer bar x Stabilizer bar link6970451
HEIGHT CONTROL COMPRESSOR AND DRYER
Height control compressor x Bracket2930021
Height control filter x Height control compressor6.46557 in.´lbf
Bracket x Body2930021
HEIGHT CONTROL VALVE
Height control set bolt2930021

A23510
Vehicle Speed
(64 km/h and 113 km/h)Between
40 mph and 70 mph
Idling
Ignition Switch OFF
10 minutes
Time Warm up
(Note: Even when vehicle stops during driving pattern, test can be resumed)NOTICE:
This test will not be completed
if the vehicle is driven under
absolute constant speed
condition such as with cruise
control activated. (6)
(5) DI±28
± DIAGNOSTICSENGINE
222 Author: Date:
2005 SEQUOIA (RM1146U)
2. CATALYST MONITOR (ACTIVE AIR±FUEL RATIO CONTROL TYPE)
(a) Preconditions
The monitor will not run unless:

The MIL is OFF
(b) Drive Pattern
(1) Connect a hand±held tester or OBD II scan tool to the DLC3.
(2) Turn the ignition switch to ON.
(3) Turn the tester or scan tool ON.
(4) Clear DTCs (where set) (see page DI±43).
(5) Start the engine and warm it up.
(6) Drive the vehicle at between 40 mph and 70 mph (64 km/h and 113 km/h) for at least 10 minutes.
(c) Monitor Status
(1) Check the Readiness Monitor status displayed on the tester or scan tool.
(2) If the status does not switch to COMPL (complete), extend the driving time.

± DIAGNOSTICSENGINE
DI±49
243 Author: Date:
2005 SEQUOIA (RM1146U)PURGE DENSITY
Learning value of purge density/
Min.: ±50, Max.: 350Idling: ±40 to 0 %Service data
PURGE FLOWPurge flow:
Min.: 0 %, Max.: 102.4 %0 to 100 %: Idling'
EVAP PURGE VSVEVAP (Purge) VSV control duty:
Min.: 0 %, Max.: 100 %0 to 100 %: During idlingOrder signal from ECM
VAPOR PRESSVapor pressure:
Min.: ±4.125 kPa, Max.: 2.125 kPa0 kPa: Fuel tank cap removed
Pressure inside fuel tank moni-
tored by the vapor pressure sen-
sor
KNOCK CRRT VAL
Correction learning value of
knocking:
Min.: ±64 CA, Max.: 1,984 CA0 to 22 CA:
Driving, 44 mph (70 km/h)Service data
KNOCK FB VALFeedback value of knocking:
Min.: ±64 CA, Max.: 1,984 CA±22 to 0 CA
Driving, 44 mph (70 km/h)Service data
ACCEL POS #1
Absolute Accelerator Pedal Posi-
tion (APP) No. 1:
Min.: 0 %, Max.: 100 %10 to 22 %: accelerator pedal is
released
54 to 86 %: accelerator pedal is
fully depressed
'
ACCEL POS #2Absolute APP No. 2:
Min.: 0 %, Max.: 100 %
12 to 42 %: accelerator pedal is
released
66 to 98 %: The accelerator pedal
is fully depressed
'
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: accelerator pedal is
released.
2.6 to 4.5 V: or pedal is fully de-
pressed.
'
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 5 V
1.2 to 2.0 V: accelerator pedal is
released.
3.4 to 5.3 V: accelerator pedal is
fully depressed.
'
ACCEL IDL POS
Whether or not accelerator pedal
position sensor detecting idle:
ON or OFF
ON: Idling'
THRTL LEARN VAL
Throttle valve fully closed
(learned value):
0.4 to 0.8 V'
ACCEL SSR #1 AD
Accelerator fully closed value No.1
(AD):
Min.: 0, Max.: 4.98 V
'ETCS service data
ACCEL LRN VAL#1
Accelerator fully closed learning
value No.1:
Min.: 0, Max.: 124.512
'ETCS service data
ACCEL LRN VAL#2
Accelerator fully closed learning
value No.2:
Min.: 0, Max.: 124.512
'ETCS service data
FAIL #1
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'
FAIL #2
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'

DI±50
± DIAGNOSTICSENGINE
244 Author: Date:
2005 SEQUOIA (RM1146U)ST1
Starter signal:
ON or OFFON: Cranking'
SYSGUARD JUDGESystem guard:
ON or OFF'ETCS service data
OPN MALFUNCTIONOpen side malfunction:
ON or OFF'ETCS service data
THROTTLE POSAbsolute throttle position sensor:
Min.: 0 %, Max.: 100 %
10 to 24 %: Throttle fully closed

64 to 96 %: Throttle fully openRead the value with intrusive op-
eration (active test)
THROTTL IDL POS
Whether or not throttle position
sensor detecting idle:
ON or OFF
ON: Idling'
THRTL REQ POSThrottle requirement position:
Min.: 0 V, Max.: 5 V0.5 to 1.0 V: Idling'
THROTTLE POSThrottle sensor positioning:
Min.: 0 %, Max.: 100 %10 to 18 %: IdlingCalculated value based on VTA1
THROTTLE POS #2Throttle sensor positioning #2:
Min.: 0 %, Max.: 100 %'Calculated value based on VTA2
THROTTLE POS #1
Throttle position sensor No. 1
output voltage:
Min.: 0 V, Max.: 4.9 V
'ETCS freeze data
THROTTLE POS #2
Throttle position sensor No.2 out-
put voltage:
Min.: 0 V, Max.: 4.9 V
'ETCS freeze data
THROTTLE POS #1Throttle position No. 1:
Min.: 0 V, Max.: 5 V
0.5 to 1.2 V: Throttle fully closed

3.2 to 4.8 V: Throttle fully opened'
THROTTLE POS #2Throttle position No. 2:
Min.: 0 V, Max.: 5 V
2.0 to 2.9 V: Throttle fully closed

4.6 to 5.5 V: Throttle fully openRead the value with intrusive op-
eration (active test)
THRTL COMND VALThrottle position command value:
Min.: 0 V, Max.: 4.98 V0.5 to 4.8 VETCS service data
THROTTLE SSR #1
Throttle sensor opener position
No. 1:
Min.: 0 V, Max.: 4.98 V
0.6 to 0.9 VETCS service data
THROTTLE SSR #2
Throttle sensor opener position
No. 2:
Min.: 0 V, Max.: 4.98 V
2.2 to 2.6 VETCS service data
THRTL SSR #1 AD
Throttle sensor opener position
No.1 (AD):
Min.: 0 V, Max.: 4.98 V
0.6 to 0.9 VETCS service data
THROTTLE MOT
Whether or not throttle motor con-
trol permitted:
ON or OFF
ON: IdlingRead the value with the power
switch ON (Do not start engine)
THROTTLE MOTThrottle motor current:
Min.: 0 A, Max.: 80 A0 to 3.0 A: Idling'
THROTTLE MOTThrottle motor:
Min.: 0 %, Max.: 100 %0.5 to 40 %: Idling'
THROTTLE MOTThrottle motor current:
Min.: 0 A, Max.: 19.92 A0 to 3.0 A: Idling'
THROTL OPN DUTYThrottle motor opening duty ratio:
Min.: 0 %, Max.: 100 %0 to 40 %: During idlingWhen accelerator pedal de-
pressed, duty ratio increased
THROTL CLS DUTYThrottle motor closed duty ratio:
Min.: 0 %, Max.: 100 %0 to 40 %: During idlingWhen accelerator pedal released
quickly, duty ratio increased
THRTL MOT (OPN)Throttle motor duty ratio (open):
Min.: 0 %, Max.: 100 %'ETCS service data

± DIAGNOSTICSENGINE
DI±53
247 Author: Date:
2005 SEQUOIA (RM1146U)A/C SIG
A/C signal: ON or OFFON: A/C ON'
ELECT LOAD SIGElectrical load signal:
ON or OFFON: Headlights or defogger is
turned ON'
STOP LIGHT SWStop lamp switch:
ON or OFFON: brake pedal is depressed.'
+BM
Whether or not electric throttle
control system power inputted:
ON or OFF
ON: Idling'
+BM VOLTAGE+BM voltage:
Min.: 0, Max.: 19.9210 to 15 V: IdlingETCS service data
BATTERY VOLTAGEBattery voltage:
Min.: 0 V, Max.: 65.535 V9 to 14 V: Idling'
ACTUATOR POWERActuator power supply:
ON or OFFON: IdlingETCS service data
ATM PRESSUREAtmospheric pressure:
Min.: 0 kPa, Max.: 150 kPaEquivalent to atmospheric pres-
sure (absolute pressure)'
SECOND AIR VSVSecondary air injection system
statusON: Secondary air injection sys-
tem operation'
ACT VSVA/C cut status for Active Test:
ON or OFF'Active Test support data
EVAP (Purge) VSVVSV status for EVAP control:
ON or OFF'Active Test support data
FUEL PUMP / SPDFuel pump/speed status:
ON or OFF'Active Test support data
VVT CTRL B1VVT control status:
ON or OFF'Active Test support data
VVT CTRL B2VVT control status:
ON or OFF'Active Test support data
VACUUM PUMP
Key±off EVAP system pump sta-
tus:
ON or OFF
'Active Test support data
EVAP VENT VAL
Key±off EVAP system vent valve
status:
ON or OFF
'Active Test support data
TC/TE1TC and TE1 terminal of DLC3:
ON or OFF''
VVTL AIM ANGL #1VVT aim angle (bank 1):
Min.: 0 %, Max.: 100 %0 %: IdlingVVT duty signal value during intru-
sive operation
VVTL AIM ANGL #2VVT aim angle (bank 1):
Min.: 0 %, Max.: 100 %0 %: IdlingVVT duty signal value during intru-
sive operation
VVT CHNG ANGL #1VVT change angle:
Min.: 0FR, Max.: 60FR0 to 5 FR: IdlingDisplacement angle during intru-
sive operation
VVT CHNG ANGL #2VVT change angle:
Min.: 0FR, Max.: 60FR0 to 5 FR: IdlingDisplacement angle during intru-
sive operation
VVT OCV DUTY B1VVT OCV operation duty:
Min.: 0 %, Max.: 100 %0 %: IdlingRequested duty value for intrusive
operation
VVT OCV DUTY B2VVT OCV operation duty:
Min.: 0 %, Max.: 100 %0 %: IdlingRequested duty value for intrusive
operation
FC IDLFuel cut idle:
ON or OFFON: Fuel cut operation
FC IDL = ºONº when throttle valve
fully closed and engine speed over
2,800 rpm

A23661
Vehicle Speed
(64 km/h and 113 km/h)Between
40 mph and 70 mph
Idling
Ignition Switch OFF
10 minutes
Time Warm up
(Note: Even if vehicle stops during driving pattern, test can be resumed)NOTICE:
This test will not be completed
if the vehicle is driven under
absolutely constant speed
conditions such as with cruise
control activated. (h)
(g)
MISFIRE MON ..................... AVAILREADINESS TESTS
CAT EVAL ......................... INCMPL
HTD CAT EVAL ...................... N/A
EVAP EVAL ....................... INCMPL
2nd AIR EVAL .......................... N/A
A/C EVAL ................................ N/A
O2S EVAL ........................ INCMPL
O2S HTR EVAL .................. INCMPL
EGR EVAL ...............................N/A COMP MON ........................ AVAIL FUEL SYS MON ................... AVAIL
A76855
A23660
DI±154
± DIAGNOSTICSENGINE
348 Author: Date:
2005 SEQUOIA (RM1146U)
CONFIRMATION DRIVING PATTER
HINT:

This confirmation driving pattern is used in steps 5, 8 and 11 of the following diagnostic troubleshooting
procedure when using either a hand±held tester.

Performing this confirmation pattern will activate the Heated Oxygen (HO2) sensor monitor. (The cata-
lyst monitor is performed simultaneously.) This is very useful for verifying the completion of a repair.
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the tester or scan tool ON.
(d) Clear DTCs (where set) (see page DI±43).
(e) If using a hand±held tester, select the following menu
items: DIAGNOSIS / CARB OBD II / READINESS
TESTS.
(f) Check that O2S EVAL is INCMPL (incomplete).
(g) Start the engine and warm it up.
(h) Drive the vehicle at between 40 mph and 70 mph (64 km/h
and 113 km/h) for at least 10 minutes.
(i) Note the state of the Readiness Tests items. Those items
will change to COMPL (complete) as O2S EVAL monitor
operates.
(j) On the tester, select the following menu items: DIAGNO-
SIS / ENHANCED OBD II / DTC INFO / PENDING
CODES and check if any DTCs (any pending DTCs) are
set.
HINT:
If O2S EVAL does not change to COMPL, and any pending
DTCs fail to set, extend the driving time.