2001 TOYOTA SEQUOIA DLC3 Ts

DI±638
± DIAGNOSTICSAUTOMATIC TRANSMISSION
832 Author: Date:
2005 SEQUOIA (RM1146U) Engine speed ± Turbine speed (NE ± NT)
(After transition from 4th to 5th gear)
±Less than 150 rpm
Vehicle speed
(After transition from 4th to 5th gear)±Less than 100 km/h (62.2 mph)
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Both of the following conditions are met: Condition (A), and Condition (B), (C) or (D)
Condition (A)
Turbine speed/Output speed3.30 to 7.50
Condition (B)
Turbine speed/Output speed1.28 to 1.53
Condition (C)
Turbine speed ± Output speed x 4th gear ratio
(NT ± NO x 4th gear ratio)1,000 rpm or more
Condition (D)
Turbine speed ± Output speed x 5th gear ratio
(NT ± NO x 5th gear ratio)1,000 rpm or more
INSPECTION PROCEDURE
1 Check other DTCs output (in addition to DTC P0781).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP0781º is outputA
ºP0781º and other DTCsB
HINT:
If any other codes besides ºP0781º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±639
833 Author: Date:
2005 SEQUOIA (RM1146U)
2 Perform active test
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
HINT:
While driving, the shift position can be forcibly changed with the hand±held tester.
Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you
to confirm the problem (See page DI±567).
Standard:
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]

Press º"º button: Shift up

Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
HINT:

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

The 4th to 5th up±shiftings must be performed with the accelerator pedal released.

The 5th to 4th down±shiftings must be performed with the accelerator pedal released.

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the hand±
held tester.
OK:
Gear position changes in accordance with the tester command.
NG Repair or replace valve body

(See page AT±10).
OK

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±659
853 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
LINE PRESS UP *
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]

Vehicle Stopped.

IDL: ON
[HINT]
OFF: Line pressure up (When the active test of ºControl the Line Pres-
sure Upº is performed, the ECM commands the SLT solenoid to turn
off).
ON: No action (normal operation)
±
*: ºLINE PRESS UPº in the ACTIVE TEST is performed to check the line pressure changes by connecting
the SST to the automatic transaxle, which is used in the HYDRAULIC TEST (See page DI±540) as well.
HINT:

The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

Normally, the line pressure detected in the ACTIVE TEST is approximately half of the value detected
in the HYDRAULIC TEST's stall test.

DI±660
± DIAGNOSTICSAUTOMATIC TRANSMISSION
854 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P2714).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP2714º is outputA
ºP2714º and other DTCsB
HINT:
If any other codes besides ºP2714º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±669
863 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
AT FLUID TEMP 2
ATF Temp. Sensor Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature when cold soak
HINT:
When DTC P2742 is output and hand±held tester output is 150C (302F) or more, there is a short circuit.
When DTC P2743 is output and hand±held tester output is ±40C (±40F), there is an open circuit.
Measure the resistance between terminal THO2 (OT2) and body ground.
Temperature DisplayedMalfunction
±40°C (±40°F)Open circuit
150°C (302°F) or moreShort circuit

G23400G23400D14177
Accelerator Pedal
Opening Angle
Lock±up OFF
Lock±up ON
"time Engine Speed
Accelerator Pedal
Fully Released DI±676
± DIAGNOSTICSAUTOMATIC TRANSMISSION
870 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
LOCK UP
[Test Details]
Control the shift solenoid SLU to set the automatic transmission to the
lock±up condition.
[Vehicle Condition]

Throttle valve opening angle: Less than 35 %

Vehicle Speed: 60 km/h (37 mph) or more
Possible to check the SLU opera-
tion.
HINT:

This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.

This test can be conducted in the 5th gear.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
HINT:

When changing the accelerator pedal opening angle while driving, if the engine speed does not
change, lock±up is on.

Slowly release, but not fully, the accelerator pedal in order to decelerate. (Fully releasing the pedal will
close the throttle valve and lock±up may be turned off automatically.)

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±677
871 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P2757).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP2757º is outputA
ºP2757º and other DTCsB
HINT:
If any other codes besides ºP2757º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A

DIDCF±01
F19439
Crankshaft
Position SensorEngine Room R/B No. 3
Engine Room J/B
Instrument
Panel J/B

STOP Fuse

IGN1 Fuse

ECU±IG Fuse
Stop Light
Switch
Combination Meter
Height Control Switch Body ECU
ECM Engine Room R/B No. 2
Suspension Control ECU
Translate ECU
4LO Switch
2WD/4HI Switch
Height Control Mode Select SwitchIgnition Switch
Height Control Indicator
Fusible Link Block

AIR SUS Fuse

AM2 Fuse

Height Control Manual IndicatorCenter Diff. Lock Switch
DLC3
Vehicle Speed Sensor
Vehicle Speed Sensor

AIR SUS Relay

AIR SUS No. 2 Fuse DI±696
± DIAGNOSTICSAIR SUSPENSION SYSTEM
890 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION