2001 TOYOTA PRIUS battery

THS (TOYOTA HYBRID SYSTEM)
M-UU,
VU, WU
M-SDOWN
G-UU,
VU, WU
CONT 3
SENSORS ACTUATORS
INVERTER (for MG1)
INVERTER (for MG2)
G-SDOWN
DATA LINK CONNECTOR 3 SIL, TC
IGCT RELAYAUXILIARY
BATTERY MRELBATT
BATTERY ECU
ABS ECU
VEHICLE SPEED SIGNAL
(for Hybrid Transaxle)
ACCELERATOR PEDAL
POSITION SENSOR
SHIFT POSITION SENSOR
CRUISE CONTROL SWITCH
AIRBAG SENSOR ASSEMBLY
CIRCUIT BREAKER SENSOR
INTERLOCK SWITCH
(for Inverter Cover and Service Plug)
STOP LIGHT SWITCH
A / C ECU
CONVERTER NODD
MG2
M-REF,
SIN, COS
MG1
G-REF,
SIN, COS
ECM
COMBINATION METER

Vehicle Speed Signal SPD
INVERTER
(for MG1)
INVERTER
(for MG2)
CONT 2
SYSTEM MAIN RELAY NO.1
SYSTEM MAIN RELAY NO.2
SYSTEM MAIN RELAY NO.3
G-MOTT
M-MOTT
CONT 1
HV ECU
HTD, DTH
HTB, BTH
VPA1, 2
SFT, P, R,
N, D, B
CCS
ABFCS
ACS
ILK
STP EGON
HTE, ETH
ACON
G-INVT
G-IU, IV, IW
M-SINV, FINV
M-INVT
M-IU, IV, IW
GO
SPDO
ESTP
IB
G-SINV, FINV
MG1
MG2
28
2. Construction
The configuration of the THS control system in the Prius is shown in the following chart.

THS (TOYOTA HYBRID SYSTEM)
HV ECUG-SDOWNInverter
(for MG1)
MG1
MG2
M-UU, VU, WUSwitching Signal
Switching Signal
G-SIN, COS
M-SIN, COS
Inverter
(for MG2) G-UU, VU, WU
M-SDOWN
G-REF
M-REF
30
5. Inverter Control (for MG1, MG2)
The HV ECU transmits a signal to the power transistor in the inverter (G-UU, VU, WU, M-UU, VU, WU)
for switching the U, V, W phase of the stator coil of MG1 and MG2, based on the rotor position information
sent from MG1, 2 (G-SIN, COS, M-SIN, COS) and the SOC of the HV battery sent from the battery ECU.
When shutting down the current to MG1, 2, a signal is sent to the inverter from the HV ECU (G-SDOWN,
M-SDOWN).
Clutchless System
A clutchless system has been adopted to keep the front wheels and MG2 linked mechanically via gears and
a chain. To disengage the drive force in the neutral position, the N position signal from the shift position
sensor turns OFF all the power transistors in the inverter (which connects the MG1 and the MG2) in order
to shut down the operation of the MG1 and the MG2, thus rendering the drive force at the wheels to zero.
In this state, even if the engine is running, the MG1 merely freewheels in the no-load state.
Therefore, if the vehicle is allowed to operate continuously in the N position in a stationary state such as
in heavy traffic, the SOC (state of charge) of the HV battery will continue to drop lower and lower.
6. Battery ECU
The SOC, temperature and the voltage of HV battery are detected by the battery ECU, and this information
is sent to HV ECU.

THS (TOYOTA HYBRID SYSTEM)
182TH33
31
± REFERENCE ±
The MG1 and the MG2 are generally shut down when the shift lever is in the N position.
However, the shut-down function is canceled under the following exceptions:

During driving, if the brake pedal is depressed and a wheel locks up, the ABS is activated. After this, low
torque is requested from the MG2 to provide supplemental power in order to restart the rotation of the wheel.
Even if the shift lever is in the N position at this time, the shut-down function is canceled to allow the wheel
to rotate. After the wheel rotation has been restarted, the system resumes its shut-down function.

When the vehicle is driven in the D or B position and the brake pedal is depressed, the regenerative brake
operates. At this time, as the driver moves the shift lever to the N position, the brake hydraulic pressure in-
creases while the request torque of the regenerative brake decreases gradually so as not to create a sluggish
brake feel. After this, the system effects its shut-down function.
When any of the conditions described below is pres-
ent, the message prompt as shown appears in the
multi information display, accompanied by the illu-
mination of the master warning light and the continu-
ous sounding of the buzzer.

The ªREADYº light is illuminated, the shift lever
is in the N position, and the HV battery is dis-
charged.

The ªREADYº light is illuminated, the shift lever
is in the N position, and the driver's door is open.

The ªREADYº light is illuminated, the parking brake is engaged, the shift lever is in the B or D position, and
the driver's door is open.

THS (TOYOTA HYBRID SYSTEM)
182TH22
1. READY Light
2. Output Control
Warning Light 3. Master Warning Light
4. Malfunction Indicator light 5. Discharge Warning Light
6. EMPS Malfunction
Warning Light7. HV Battery Warning Light
8. Hybrid System
Malfunction Warning
Light 32
INDICATOR AND WARNING LIGHT
The warning lights of the Prius are different from those on conventional vehicles. Inspection and repair
should be performed while referring to the troubleshooting section in the 2001 Prius repair manual
(RM778U).

Center Meter 
Multi Information Display 
1. READY lightTurns on when the ignition switch is turned to START to indicate that the ve-
hicle is ready to drive.
2. Output control
warning lightTurns on when the remaining HV battery charge becomes insufficient at R
range or when there is an abnormal temperature rise in the HV battery due
to continuous driving under heavy loads. It may also light when the HV bat-
tery temperature is low (after starting at low temperatures). The hybrid sys-
tem output is limited while this light is on.
Travel at reduced speeds (avoid sudden acceleration) while the light is lit.
3. Master warning
lightTurns on with buzzer sounding by linked operation with warning lights ª6º
to ª8º on the multi center display.
4. Malfunction
indicator lightTurns on when there is a malfunction in the engine control system.
5. Discharge warning
lightTurns on when there is a malfunction in the 12 V charging system (converter
assembly).
If it turns on together with the master warning light and hybrid system
warning light, check the diagnostic code.
6. EMPS malfunction
warning lightTurns on when there is a malfunction in the EMPS control system.
7. HV battery warning
lightTurns on when the HV battery is discharged to the lower limit.
8. Hybrid system
warning lightTurns on when a malfunction in MG1, 2, inverter, HV battery or HV ECU
is detected.

THS (TOYOTA HYBRID SYSTEM)
182CH05
Stator
Rotor
Speed Sensor (Resolver)
MG1
182CH04
Stator
Rotor
Speed Sensor (Resolver)
MG2
182TH07
N.m
350
300
250
200
150
100
50
0
01000 30002000 50004000 60000 20 40
30
10 kW
Torque
Engine Speed (rpm)Output
Torque
Output
33
MG1 AND MG2 (MOTOR GENERATOR NO.1 AND NO.2)
DESCRIPTION
Both the MG1 and the MG2 are compact, lightweight, and highly efficient alternating current permanent
magnet synchronous type.
Serving as the source of supplemental motive force that provides power assistance to the engine as needed,
the electric motor helps the vehicle achieve excellent dynamic performance, including smooth start-offs
and acceleration. When the regenerative brake is activated, MG2 converts the vehicle's kinetic energy into
electrical energy, which is then stored in the HV battery.
MG1 recharges the HV battery and supplies electrical power to drive MG2. In addition, by regulating the
amount of electrical power generated (thus varying the generator's rpm), MG1 effectively controls the
continuously variable transmission function of the transaxle. MG1 also serves as the starter to start the
engine.

MG2 Specifications 
TypePermanent Magnet
Motor (1CM)
Rated voltage [V]273.6
Maximum output [kW] (rpm)33 / (1040
5600)
Maximum torque [N.m (kgf.m) (rpm)350 / (0
400)
Amperage at maximum torque [A]351
Cooling systemWater-cooled

Performance Curve 

THS (TOYOTA HYBRID SYSTEM)
182TH29
Rotational
Magnetic FieldU PhaseStator Coil
Rotor
Repulsion
W Phase V Phase
: From inverter
: Connected internally in the motor
Attruction
182TH09
Magnetized Side
Coil A
Coil B
Coil C Speed Sensor
(Resolver)Output Side
182TH10
Inverter Power Cable HV Battery
Junction
BlockPortion routed through
the center floorAuxiliary
Battery
Under-
the-Floor
Reinforcement
12 V
Power Cable
Voltage 
Power Cable
Voltage

34
1. Permanent Magnet Motor
When a three-phase alternating current is passed
through the three-phase windings of the stator
coil, a rotational magnetic field is created in the
electric motor. By controlling this rotating mag-
netic field according to the rotor's rotational posi-
tion and speed, the permanent magnets that are
provided in the rotor become attracted by the ro-
tating magnetic field, thus generating torque.
The generated torque is for all practical purposes
proportionate to the amount of current, and the
rotational speed is controlled by the frequency of
the alternating current.
Furthermore, a high level of torque, all the way to
high speeds, can be generated efficiently by prop-
erly controlling the rotating magnetic field and the
angles of the rotor magnets.
2. Speed Sensor (Resolver)
This is an extremely reliable and compact sensor
that precisely detects the magnetic pole position,
which is indispensable for ensuring the efficient
control of MG1 and MG2.
The sensor's stator contains 3 coils as illustrated, and
output coils B and C are electrically staggered 90 de-
grees. Because the rotor is oval, the distance of the
gap between the stator and the rotor varies with the
rotation of the rotor. Thus, by passing an alternating
current through coil A, output that corresponds to the
sensor rotor's position is generated by coils B and C.
The absolute position can then be detected from the
difference between these outputs.
In addition, the amount of positional variance
within a predetermined time is calculated by the
HV ECU, thus enabling this sensor to be used as
an rpm sensor.
3. Power Cable
The power cable is a high-voltage, high-amperage
cable that connects the HV battery with the inverter,
and the inverter with MG1 and MG2. Starting from
the connector at the left front of the HV battery lo-
cated in the luggage compartment, the power cable
is routed under the rear seat, through the floor panel,
along the under-the-floor reinforcement, and con-
nects to the inverter in the engine compartment. A
shielded cable is used for the power cable in order to
reduce electromagnetic interference.
The 12 V  wiring of the auxiliary battery also
follows the same route.
For identification purposes, the high-voltage wir-
ing harness and connectors are color-coded
orange to distinguish them from those of the ordi-
nary low-voltage wiring.

THS (TOYOTA HYBRID SYSTEM)
182TH26
Inverter
Converter
182TH15
Inverter
HV
Battery
Ignition Signal
Ground
Voltage
Detection
Circuit
Voltage
Detection
Circuit
Bridge Circuit for MG2
Amperage
Sensor
Signal Processor /
Protective Function Processor
Bridge Circuit for MG1
Amperage
Sensor
MG2
HV ECU
MG1
182TH27
Reservoir Tank
Radiator
Water Pump35
INVERTER
1. General
The inverter is an electric power converter that
converts the direct current of the Hybrid vehicle's
high-voltage battery (DC 273.6 V) and the alter-
nating current of the MG1 and MG2.
Consisting of 2 three-phase bridge circuits for
MG1 and MG2, respectively, and each containing
6 power transistors, the inverter converts direct
current and three-phase alternating current. The ac-
tivation of the power transistors is controlled by the
HV ECU. In addition, the inverter transmits in-
formation that is needed for current control, such as
the output amperage or voltage, to the HV ECU.
Together with MG1 and MG2, the inverter is
cooled by the dedicated radiator of the coolant
system that is separate from that of the engine.
2. System Diagram
3. Cooling System
A cooling system via water pump for the inverter
and MG1, 2 has been added.
The HV ECU controls the water pump with cool-
ant temperature.
It is separated with the engine cooling system.

THS (TOYOTA HYBRID SYSTEM)
182TH26
Inverter
Converter
182TH17
F. L
MAINF.L DCDC12 V

Output
Auxiliary
Battery S34B20
Shielded 12 VInverter
SDC273.6 V
DC / DC Converter
Input Filter
20 V
Converter Control Circuit
HV ECU A / C ECUIG
IDH NODD 36
CONVERTER
1. General
The power source for auxiliary equipment of the
vehicle such as the lights, audio system, and the air
conditioner cooling fan, as well as the ECUs, is
based on a 12 V system. Because the THS genera-
tor outputs at 273.6 V, the converter is used to
transform the voltage from DC273.6 V to DC 12
V in order to recharge the auxiliary battery. The
converter is installed on the underside of the in-
verter.
2. Operation

The DC273.6 V input is initially converted into alternating current by the transistor bridge circuit and
transformed into a low voltage by the transformer. After this, the current is rectified, smoothed (into direct
current) and converted into DC12 V.

The voltage at the positive terminal of the auxiliary battery is monitored by the converter and is maintained
at a constant level. Consequently, the voltage of the auxiliary battery is unrelated to the engine rpm (even
if the engine is stopped) and to the auxiliary equipment (output current of converter).