2001 TOYOTA PRIUS wheel

2001 PRIUS (EWD414U)
G ELECTRICAL WIRING ROUTING
Position of Parts in Instrument Panel
A 7 A/C Amplifier
A 8 A/C Amplifier
A 9 A/C Amplifier
A 10 A/C Room Temp. Sensor
A 11 A/C Solar Sensor
A 12 A/C Thermistor
A 13 Accel Position Sensor
A 14 Air Inlet Control Servo Motor
A 15 Air Mix Control Servo Motor
A 16 Air Vent Mode Control Servo Motor
A 17 Airbag Sensor Assembly
A 18 Airbag Sensor Assembly
A 19 Airbag Sensor Assembly
A 20 Airbag Squib (Front Passenger Airbag Assembly)
A 21 Airbag Squib (Steering Wheel Pad)
A 22 Ashtray Illumination
B 5 Back±Up Light Relay
B 6 Blower Motor
B 7 Blower Motor Linear Controller
B 8 Body ECU
B 9 Body ECU
B 10 Brake ECU
B 11 Brake ECU
B 12 Brake ECU
B 13 Brake ECU
B 14 Brake Warning BuzzerC 7 Center Cluster SW
C 8 Cigarette Lighter
C 9 Cigarette Lighter Illumination
C 10 Combination Meter
C 11 Combination Meter
C 12 Combination SW
C 13 Combination SW
C 14 Combination SW
D 2 Data Link Connector 3
D 3 Daytime Running Light Relay
D 4 Diode (Door Courtesy)
D 5 Diode (Daytime Running Light)
E 3 EMPS ECU
E 4 EMPS ECU
E 5 EMPS ECU
E 6 EMPS ECU
E 7 Engine Control Module
E 8 Engine Control Module
E 9 Engine Control Module
E 10 Engine Control Module

2001 PRIUS (EWD414U)
TOYOTA HYBRID SYSTEM
FEATURES OF TOYOTA HYBRID SYSTEM
This system controls the following modes in order to achieve the most efficient operations to match the driving conditions.
(1) Supply of electrical power from the HV battery to motor generator no.2 provides force to drive the wheels.
(2) While the tires are driven by the engine via the planetary gears, motor generator no.1 is driven via the planetary gears to
supply electricity to motor generator no.2 to drive the wheels.
(3) When the vehicle is decelerating, kinetic energy from the wheels is recovered and converted into electrical energy and
used to recharge the HV battery by means of motor generator no.2.
The hybrid vehicle control ECU switches between these modes (1, 2, 1+2, or 3) according to the driving conditions.
However, when the state of charge of the HV battery is low, the HV battery is charged by the engine by turning motor
generator no.1.
CRUISE CONTROL OPERATION
Cruise control is the speed control device, which sets the desired speed by just operating the switch on the control panel
without pressing the accelerator pedal. This device is used when you would like to drive the vehicle at the fixed speed.
1. SET CONTROL
If you operate the SET/COAST switch when driving (The available range of set speed: between about 40 and 200 km/h) with
the main switch is ON (When power indicator comes on), the device memorizes vehicle's speed when switch is off and
controls the fixed speed.
2. SET SPEED CONTROL
This device compares the vehicle's running speed and the memorized speed, and controls the driving power of the motor
and the engine by calculating the cruise control requirements so that both speed become equivalent.
3. COAST CONTROL
If the SET/COAST switch is continued to be ON during the running with the cruise control, the device recognizes the cruise
control requirement is at 0 and decelerates the vehicle's speed. Then the device memorizes the speed when the switch is off
in order to control the fixed speed.
In each time you operate SET/COAST switch momentarily (For about 0.5 second), the memorized speed is decreased in
about 1.5 km/h. However, in case of the tap±down operation with more than 5±km/h gap between the memorized speed and
vehicle's running speed, the device memorizes the vehicle's speed when the switch is off and controls the fixed speed.
4. ACCEL CONTROL
If the RESUME/ACCEL switch is continued to be ON during the running with the cruise control, the device recognizes the
cruise control is on the acceleration side and accelerates the vehicle's speed. Then the running speed when the switch is off
is memorized to control the fixed speed.
In each time you operate RESUME/ACCEL switch momentarily (For about 0.5 second), the memorized speed is increased
in about 1.5 km/h. However, if there is more than 5±km/h gap between the memorized speed and vehicle's running speed,
this operation does not change the memorized speed. (Tap±up operation is not available.)
5. RESUME CONTROL
If the running speed is faster than the low speed limit after the cruise control is canceled manually, the fixed speed is
controlled by the OFF±ON operation of RESUME/ACCEL switch, so that the vehicle's speed returns to the memorized
speed at the time the cruise control is released.
SYSTEM OUTLINE

2001 PRIUS (EWD414U)
EMPS
In this system, the controller determines the direction and the amount of the assistant force based on the signals from the
vehicle speed sensor and the torque sensor that is built in the gear box. The controller then assists the operation of the
steering wheel by controlling the DC motor installed in the steering gear box.
E5 (C), E6 (D) EMPS ECU
(D) 5±GROUND : Approx. 12 volts with the ignition SW at ON position
(C) 2±GROUND : Always continuity
: PARTS LOCATION
CodeSee PageCodeSee PageCodeSee Page
B1136E5C36J18A37
C1036E6D36J19B37
D134J14A37J2237
D236J15B37J2637
E3A36J1637S135
E4B36J1737
: RELAY BLOCKS
CodeSee PageRelay Blocks (Relay Block Location)
324Engine Room R/B No.3 (Engine Compartment Right)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CodeSee PageJunction Block and Wire Harness (Connector Location)
2A30Instrument Panel Wire and Instrument Panel J/B (Cowl Side Panel LH)2B30Instrument Panel Wire and Instrument Panel J/B (Cowl Side Panel LH)
2G31Engine Room Main Wire and Instrument Panel J/B (Cowl Side Panel LH)
2I31Cowl Wire and Instrument Panel J/B (Cowl Side Panel LH)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CodeSee PageJoining Wire Harness and Wire Harness (Connector Location)
IA242Engine Room Main Wire and Cowl Wire (Cowl Side Panel LH)
ID142Instrument Panel Wire and Cowl Wire (Left Kick Panel)
IM144Engine Room Main Wire and Cowl Wire (Right Kick Panel)
IO144Engine Wire and Cowl Wire (Right Kick Panel)
IP144Instrument Panel Wire and Cowl Wire (Right Kick Panel)
: GROUND POINTS
CodeSee PageGround Points Location
IG42Cowl Side Panel RH
IH42Right Kick Panel
: SPLICE POINTS
CodeSee PageWire Harness with Splice PointsCodeSee PageWire Harness with Splice Points
I744Engine Wire
SYSTEM OUTLINE
SERVICE HINTS

2001 PRIUS (EWD414U)
SRS
NOTICE: When inspecting or repairing the SRS, perform the operation in accordance with the following precautionary
instructions and the procedure and precautions in the Repair Manual for the applicable model year.

Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of information
when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting the battery.

Work must be started after 90 seconds from when the ignition switch is turned to the ºLOCKº position and the
negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source so that if work is started within 90 seconds from
disconnecting the negative (±) terminal cable of the battery, the SRS may be deployed.)

When the negative (±) terminal cable is disconnected from the battery, the memory of the clock and audio system will be
canceled. So before starting work, make a record of the contents memorized in the audio memory system. When work is
finished, reset the audio systems as they were before and adjust the clock. To avoid erasing the memory in each
memory system, never use a back±up power supply from outside the vehicle.

Before repairs, remove the airbag sensor if shocks are likely to be applied to the sensor during repairs.

Do not expose the steering wheel pad, front passenger airbag assembly, side airbag assembly, seat belt pretensioner,
airbag sensor assembly or side airbag sensor directly to hot air or flames.

Even in cases of a minor collision where the SRS does not deploy, the steering wheel pad, front passenger airbag
assembly, side airbag assembly, seat belt pretensioner, airbag sensor assembly and side airbag sensor assembly
should be inspected.

Never use SRS parts from another vehicle. When replacing parts, replace them with new parts.

Never disassemble and repair the steering wheel pad, front passenger airbag assembly, side airbag assembly, seat belt
pretensioner, airbag sensor assembly or side airbag sensor assembly in order to reuse it.

If the steering wheel pad, front passenger airbag assembly, side airbag assembly, seat belt pretensioner, airbag sensor
assembly or side airbag sensor assembly has been dropped, or if there are cracks, dents or other defects in the case,
bracket or connector, replace them with new ones.

Use a volt/ohmmeter with high impedance (10 kW/V minimum) for troubleshooting the system's electrical circuits.

Information labels are attached to the periphery of the SRS components. Follow the instructions on the notices.

After work on the SRS is completed, perform the SRS warning light check.

If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the Repair
Manual.

2001 PRIUS (EWD414U)
SRS
C 1
D 11B 215A
AM2 1J 976AM2 AM1ACC
IG1
IG2
ST2
1 2 2 1 2 1 12
SPIRAL
CABLE B 14 B13 B10 B11 A6A5C2C1 10A
SRS ACC FROM POWER SOURCE SYSTEM (
SEE PAGE 50)
2E 4
2B 5
2E 2
B 5B6B23 A7A10 A12 A9C12 C9C7C104 3 2 1 4 3 2 1 3
SIDE AIRBAG
SQUIB RH S 7
SIDE AIRBAG
SQUIB LH S 6
AIRBAG SQUIB
(
FRONT PASSENGER
AIRBAG ASSEMBLY) A20
AIRBAG SQUIB
(
STEERING
WHEEL PAD) A21 IGNITION SW I15
SIDE AIRBAG SENSOR RH S 5
SIDE AIRBAG SENSOR LH S 4
HYBRID VEHICLE
CONTROL ECU H13
FUSIBLE
LINK
BLOCK
NO. 1D F1 2 , F13CAIRBAG SENSOR ASSEMBLYB A17 , A18AC, A19 ABFS
B±G B W±R W±R
B±W B±O
GR
L
P±L
L±W
LG±B
GR ±L
P
L±Y
LG
GR Y±B
Y
Y±R
Y±G
Y±R
Y±G
Y±G
Y±R
BATTERYD+ D± P+ P± SFL+ SFR±SFL± SFR+ IG2 ACC GSW2 VUPL SSL+ SSL± ESL VUPR SSR+ SSR± ESR
GR
2C 2
2G 1
120A MAIN
1
FUSIBLE
LINK BLOCK
NO. 2 F18
1 212 A 2A1C5C6
P15
PRETENSIONER
RH PRETENSIONER
LH P14
Y±B
Y
Y±B
Y
PL+ PL± PR+ PR±
P±L
(
*1)
(
*1)
(
*1)
(
*1)
(
*1)
(
*1)
(
*1)
(
*1) (
*1) (
*1) (
*1) (
*1)

2001 PRIUS (EWD414U)
SRS
The SRS is a driver and front passenger protection device which has a supplemental role to the seat belts.
When the ignition SW is turned to ACC or ON, current from the SRS ACC fuse flows to TERMINAL (B) 6 of the airbag sensor
assembly. Only when the ignition SW is on does the current flow TERMINAL (B) 5 of the airbag sensor assembly.
If an accident occurs while driving, when the frontal impact exceeds a set level, current flows to TERMINALS (B) 14, (B) 10,
(A) 2 and (C) 5 of the airbag sensor assembly to TERMINAL 1 of the airbag squibs and the pretensioners to TERMINAL 2 to
TERMINALS (B) 13, (B) 11, (A) 1 and (C) 6 of the airbag sensor assembly to TERMINAL (B) 27, (B) 28 or BODY GROUND
to GROUND, so that current flows to the front airbag squibs and the pretensioners and causes them to operate.
When the side impact also exceeds a set level, current from the ignition SW (IG2) or SRS ACC fuse flows to TERMINALS
(A) 5, (C) 2, (A) 2 and (C) 5 of the airbag sensor assembly to TERMINAL 1 of the side airbag squibs and the pretensioners to
TERMINAL 2 to TERMINALS (A) 6, (C) 1, (A) 1 and (C) 6 of the airbag sensor assembly to TERMINAL (B) 27, (B) 28 or
BODY GROUND to GROUND, causing side airbag squibs and the pretensioners to operate.
The airbag stored inside the steering wheel pad is instantaneously expanded to soften the shock to the driver.
The airbag stored inside the passenger's instrument panel is instantaneously expanded to soften the shock to the front
passenger.
Side airbags are instantaneously expanded to soften the shock of side to the driver and front passenger (w/ side airbags).
The pretensioners make sure of the seat belt restrainability.
: PARTS LOCATION
CodeSee PageCodeSee PageCodeSee Page
A17A36F134J25B37
A18B36F234J2637
A19C36F12C34J27A37
A2036F13D34J28B37
A2136F1838J2937
B936H1337P1439
B2038I1537P1539
B2138J1137S439
C10A36J22A37S539
C11B36J23B37S639
D236J24A37S739
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CodeSee PageJunction Block and Wire Harness (Connector Location)
1B27Engine Room Main Wire and Engine Room J/B (Engine Compartment Left)1J27Engine Room Main Wire and Engine Room J/B (Engine Compartment Left)
2A
2B
2C30Instrument Panel Wire and Instrument Panel J/B (Cowl Side Panel LH)
2D
()
2E
2G31Engine Room Main Wire and Instrument Panel J/B (Cowl Side Panel LH)
2K31Cowl Wire and Instrument Panel J/B (Cowl Side Panel LH)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CodeSee PageJoining Wire Harness and Wire Harness (Connector Location)
IJ144Floor No.3 Wire and Instrument Panel Wire (Under the Instrument Panel Center)
IL144Instrument Panel Wire and Engine Room Main Wire (Right Kick Panel)
: GROUND POINTS
CodeSee PageGround Points Location
ID42Cowl Side Panel LH
IH42Right Kick Panel
SYSTEM OUTLINE

2001 PRIUS (EWD414U)
1. INPUT SIGNALS
(1) Speed sensor signal
The speed of the wheels is detected and input to TERMINALS FL+, FR+, RL+ and RR+ of the brake ECU.
(2) Stop light SW signal
A signal is input to TERMINAL STP of the brake ECU when the brake pedal is depressed.
2. ABS SYSTEM OPERATION
During sudden braking the brake ECU has signals input from each sensor, which controls the current to the solenoid inside
the actuator and lets the hydraulic pressure acting on each wheel cylinder escape to the reservoir. The pump inside the
actuator is also operating at this time and it returns the brake fluid from the reservoir to the master cylinder, thus preventing
locking of the vehicle wheels.
If the brake ECU judges that the hydraulic pressure acting on the wheel cylinder is insufficient, the current on the solenoid is
controlled and the hydraulic pressure is increased. Holding of the hydraulic pressure is also controlled by the brake ECU, by
the same method as above. Pressure reduction, holding and increase are repeated to maintain vehicle stability and to
improve steerability during sudden braking.
A4, A5 ABS SPEED SENSOR FRONT LH, RH
2±1 :1.4±1.8 kW (20°C, 68°F)
A23, A24 ABS SPEED SENSOR REAR LH, RH
2±1 :1.04±1.3 kW (20°C, 68°F)
B10 (A), B11 (B), B12 (C), B13 (D) BRAKE ECU
(B) 6, (C) 1±GROUND : Approx. 12 volts with the ignition SW at ON position
(D) 22±GROUND : Always approx. 12 volts
(A) 6, (A)31±GROUND : Always continuity
: PARTS LOCATION
CodeSee PageCodeSee PageCodeSee Page
A434C10A36J1037
A534C11B36J1137
A736D236J1237
A2338E636J14A37
A2438E1036J15B37
B1A34F12C34J1637
B2B34F13D34J1737
B3C34F1838J18A37
B434G137J19B37
B8A36H5A34J2237
B10A36H6B34J2637
B11B36H1538P237
B12C36I1537S337
B13D36J137
B1436J737
: RELAY BLOCKS
CodeSee PageRelay Blocks (Relay Block Location)
223Engine Room R/B No.2 (Right Side of Reserve Tank)
324Engine Room R/B No.3 (Engine Compartment Right)
SYSTEM OUTLINE
SERVICE HINTS

L PART NUMBER OF CONNECTORS
Code Part Name Part NumberCodePart Name Part Number
Note : Not all of the above part numbers of the connector are established for the supply.
2001 PRIUS (EWD414U) A 1
A/C Condenser Fan Motor90980±11237
A 2A/C Magnetic Clutch and Lock Sensor90980±10942
A 3A/C Triple Pressure SW (A/C Dual and
Single Pressure SW)90980±10943
A 4ABS Speed Sensor Front LH90980±11003A 5ABS Speed Sensor Front RH90980±11003
A 6Ambient Temp. Sensor90980±11070
A 7A/C Amplifier90980±11911
A 8A/C Amplifier90980±11913
A 9A/C Amplifier90980±11927
A10A/C Room Temp. Sensor
A11A/C Solar Sensor90980±11919
A12A/C Thermistor
A13Accel Position Sensor90980±11144
A14Air Inlet Control Servo Motor90980±11921
A15Air Mix Control Servo Motor90980±11909A16Air Vent Mode Control Servo Motor90980±11909
A17Airbag Sensor Assembly90980±11869
A18Airbag Sensor Assembly90980±11872
A19Airbag Sensor Assembly90980±11867
A20Airbag Squib (Front Passenger Airbag
Assembly)90980±11884
A21Airbag Squib (Steering Wheel Pad)90980±10850
A22Ashtray Illumination90980±12111
A23ABS Speed Sensor Rear LH90980±11060A24ABS Speed Sensor Rear RH90980±11060
B 1Brake Actuator90980±11087
B 2Brake Actuator90980±11161
B 3Brake Actuator90980±11698
B 4Brake Fluid Level Warning SW90980±11207
B 5Back±Up Light Relay82660±20340
B 6Blower Motor90980±10214
B 7Blower Motor Linear Controller90980±11676
B 8Body ECU90980±11971
B 9Body ECU90980±11973
B10Brake ECU90980±11935
B11Brake ECU90980±11476
B12Brake ECU90980±11637
B13Brake ECU90980±11638
B14Brake Warning Buzzer90980±10906
B15Battery Blower Motor82824±47130
B16Battery Blower Motor Controller90980±11676
B17Battery ECU90980±11392
B18Battery ECU90980±11424
B19Battery Fan Relay82660±20340
B20Buckle SW and Tension Reducer LH
B21Buckle SW RH and Seat Belt Warning
Occupant Detection Sensor90980±11471
C 1Camshaft Position Sensor90980±10947
C 2Camshaft Timing Oil Control Valve90980±11162
C 3Circuit Breaker Sensor90980±11898
C 4Converter90980±10942
C 5Converter90980±11963
C 6Crankshaft Position Sensor90980±12028
C 7Center Cluster SW90980±10801
C 8Cigarette Lighter90980±10760
C 9Cigarette Lighter Illumination90980±11148
C10Combination Meter90980±11927
C11Combination Meter90980±11923
C12Combination SW90980±11594
C13Combination SW90980±11672
C14Combination SW90980±11616
D 1DC Motor90980±10838
D 2Data Link Connector 390980±11665
D 3Daytime Running Light Relay90980±12034
D 4Diode (Door Courtesy)90980±11251
D 5Diode (Daytime Running Light)90980±10962
D 6Door Courtesy SW Front LH
D 7Door Courtesy SW Front RH90980±10871D 8Door Courtesy SW Rear LH90980±10871
D 9Door Courtesy SW Rear RH
D10Door Lock Control SW Front RH90980±10797
D11Door Lock Motor and Door Unlock
Detection SW Rear LH
90980±11150
D12Door Lock Motor and Door Unlock
Detection SW Rear RH90980±11 150
D13Door Lock Motor, Door Key Lock and
Unlock SW and Door Unlock Detection SW
Front LH
90980±11858
D14Door Lock Motor, Door Key Lock and
Unlock SW and Door Unlock Detection SW
Front RH90980±11 858
E 1Engine Coolant Temp. Sensor90980±10737
E 2Engine Hood Courtesy SW90980±11189
E 3EMPS ECU90980±12012
E 4EMPS ECU90980±11579
E 5EMPS ECU90980±12120
E 6EMPS ECU90980±11923
E 7Engine Control Module90980±11421
E 8Engine Control Module90980±11476
E 9Engine Control Module90980±11637