2001 TOYOTA AVALON ignition

BE0HT-04
I12523
Ignition Switch

Key Unlock Warning Switch
Driver Side Junction Block

ECU ACC Fuse

ECU I/G No.2 Fuse

IG1 Relay

BODY ECU
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE-15
1619 Author
: Date
:
2001 AVALON (RM808U)
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
LOCATION

BE212-01
BE-88
- BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
1692 Author
: Date
:
ADJUSTMENT
ENABLING/DISABLING AUTO DOOR LOCK FUNCTION
(a) To disable auto door lock:
(1) Enter the vehicle and shut all doors.
(2) Insert the key into the ignition cylinder and turn it to
the ON position (not ACC).
(3) Open the driver's door and keep it open.
(4) Turn the key to the LOCK position and remove it
from the ignition cylinder.
(5) Insert the key into the ignition cylinder and remove
it. Repeat this operation three more times. (End this
step with the key out of the ignition cylinder.)
(6) Push the ºUNLOCKº button on the driver's door
master switch 5 times within 10 seconds. Wait at
least 10 seconds and shut the driver's door.
(7) Verify auto lock operation has been disabled by
starting the engine, putting the vehicle into a gear
and releasing the brake pedal.
(b) To enable auto door lock:
Follow the same sequence as above, except step 6. In step 6,
push the ºLOCKº button on the driver's door master switch 5
times within 10 seconds. Wait at least 10 seconds and shut the
driver 's door.

BE0IJ-03
I12855
Driver Side Junction Block

Door No.1 Fuse

Body ECUIgnition Switch
Front Door Lock Assembly

Door Lock Motor

Door Unlock Detection Motor

Door Key Lock and Unlock Switch
Rear Door Lock Assembly

Door Lock Motor

Door Unlock Detection Switch
Power Window Master Switch

Door Lock Control Switch

Driver Door ECU
- BODY ELECTRICALPOWER DOOR LOCK CONTROL SYSTEM
BE-81
1685 Author
: Date
:
2001 AVALON (RM808U)
POWER DOOR LOCK CONTROL SYSTEM
LOCATION

N21376
Wire Harness Side
123 4 56 78910
h-10-1-c
N13659
6
5
I13295
1
2
I13296
1
2
- BODY ELECTRICALPOWER MIRROR CONTROL SYSTEM
BE-1 15
1719 Author
: Date
:
2001 AVALON (RM808U)
5. INSPECT MIRROR SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side.
Tester connectionConditionSpecified condition
8 - GroundConstantContinuity
4 - GroundIgnition switch position LOCKNo voltage
4 - GroundIgnition switch position ACC or ONBattery voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
6. INSPECT MIRROR SWITCH INDICATOR LIGHT OP-
ERATION
Connect the positive (+) lead from the battery to terminal 5 and
the negative (-) lead to terminal 6, and check that the indicator
light does not light up, replace the switch.
7. w/o Mirror defogger and driving position memory:
INSPECT MIRROR MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2, and check that
the mirror turns to the left side.
(b) Reverse the polarity, and check that the mirror turns to the
right side.

BE1DG-01
I13484
Ignition Switch
Driver Side Junction Block

PWR - OUTLET Fuse (No.1,2)
Power Outlet Main Switch
Power Point Relay
Power Outlet Socket
Power Outlet Main SwitchPower Point Relay
Driver Side Junction Block

PWR - OUTLET Fuse (No.1,2)
Ignition Switch
Power Outlet Socket
Floor shift vehicle:
Column shift vehicle:
- BODY ELECTRICALPOWER OUTLET
BE-13
1617 Author
: Date
:
2001 AVALON (RM808U)
POWER OUTLET
LOCATION

BE0HG-33
BE-80
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1684 Author
: Date
:
ADJUSTMENT
HOW TO RESET POWER WINDOW MOTOR (LIMIT SWITCH)
NOTICE:
If the jam protection function is not functioning properly, perform the following procedures.
HINT:
It is necessary to reset the power window motor (in initial position for the limit switch) when separating the
window regulator from the power window motor or operating the window regulator with the door glass not
installed.
(a) Remove the power window motor.
HINT:
Place matchmarks on the power window motor and window regulator gear.
(b) Connect the power window motor and power window switch to the wire harness of the vehicle.
(c) Turn the ignition switch ON.
(d) Press the power window UP switch until the motor completes 6 to 10 rotations (4 seconds of rotation
or more).
(e) Assemble the power window motor and regulator.
HINT:

Install the motor when the regulator arm is below the middle point.

Align the matchmarks on the power window motor and window regulator gear when installing the pow-
er window motor.
(f) Assemble the power window regulator and door glass.
HINT:
Never rotate the motor downward until the completion of the window glass installation.
(g) Connect the power window switch to the wire harness and turn the ignition switch ON.
(h) Repeat UP and DOWN operation several times manually.
(i) Check AUTO UP " AUTO DOWN automatic operation is normal.
NOTICE:

The jam protection function does not operate immediately after performing reset.

If the jam protection function is triggered and the window lowers after the window has been fully
closed by AUTO UP operation (step i), reset the power window motor again.
(j) Check the power window function.

I12857
1
14
BE1DW-01
I12858
25
I14262
1 2
3 4 5 6
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE-73
1677 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
1. Using an ammeter:
INSPECT ONE TOUCH POWER WINDOW SYSTEM/
CURRENT OF CIRCUIT
(a) Disconnect the connector from the master switch.
(b) Connect the positive (+) lead from the ammeter to termi-
nal 1 on the wire harness side connector and the negative
(-) lead to negative (-) terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal
14 on the wire harness side connector.
(d) As the window goes down, check that the current flow is
approximately 7 A.
(e) Check that the current increases up to approximately
14.5 A or more when the window stops going down.
HINT:
The PTC opens some 4 - 90 seconds after the window stops
going down, so that check must be made before the PTC oper-
ates.
If the operation is as specified, replace the driver door ECU.
2. Using an ammeter with a current-measuring probe:
INSPECT ONE TOUCH POWER WINDOW SYSTEM/
CURRENT OF CIRCUIT
(a) Remove the driver door ECU with connectors connected.
(b) Attach a current-measuring probe to terminal 25 of the
wire harness.
(c) Turn the ignition switch ON and set the power window
switch in the down position.
(d) As the window goes down, check that the current flow is
approximately 7 A.
(e) Check that the current increases up to approximately
14.5 A or more when the window stops going down.
HINT:
The PTC opens some 4 - 90 seconds after the window stops
going down, so that check must be made before the PTC oper-
ates.
If operation is as specified, replace the driver door ECU.
3. INSPECT REAR POWER WINDOW SWITCH CONTI-
NUITY
Switch positionTester connectionSpecified condition
UP5 - 4, 2 - 6Continuity
OFF4 - 6, 2 - 6No continuity
DOWN2 - 5, 4 - 6Continuity
If continuity is not as specified, replace the switch.

BE0IH-03
I12534
Driver Side Junction Block

FL P/W, FR P/W, RL P/W, RR P/W Fuse

Power Main Relay

Body ECU
Front Power Window MotorIgnition SwitchPower Window Switch
(Passenger Door ECU)
Rear Power Window Motor
Power Window Master Switch
(Driver Door ECU)
Rear Power Window Switch
BE-72
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1676 Author
: Date
:
2001 AVALON (RM808U)
LOCATION