2001 TOYOTA AVALON Power window

I12760
1
2
4
5
I12761
1
2
4
5
I12762
1
2
4
5
I12763
1
2
4
5
I12768
1
2
3
5
BE-78
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1682 Author
: Date
:
2001 AVALON (RM808U)
14. Driver 's Door (Window Up):
INSPECT JAM PROTECTION LIMIT SWITCH OPERA-
TION
(a) Connect the negative (-) lead from the ohmmeter to ter-
minal 5 and the positive (+) lead to terminal 4.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2.
(c) Check that the continuity exists when the window goes
up.
(d) Check that the no continuity exists when the window is in
the fully closed position.
If operation is not as specified, replace the motor.
NOTICE:
If connecting the wire harness wrongly, the sensor might
be damaged so caution is necessary.
15. Driver 's Door (Window Down):
INSPECT JAM PROTECTION LIMIT SWITCH OPERA-
TION
(a) Connect the negative (-) lead from the ohmmeter to ter-
minal 5 and the positive (+) lead to terminal 4.
(b) Connect the positive (+) lead from the battery to terminal
2 and the negative (-) lead to terminal 1.
(c) Check that the continuity exists when the window goes
down.
(d) Check that the no continuity exists when the window is in
the fully opened position.
If operation is not as specified, replace the motor.
NOTICE:
If connecting the wire harness wrongly, the sensor might
be damaged so caution is necessary.
16. Driver 's Door:
INSPECT JAM PROTECTION PULSE SWITCH OP-
ERATION
(a) Connect the positive (+) lead from the TOYOTA electrical
tester to terminal 3 and the negative (-) lead to terminal
5.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2.
(c) Check that pulse is generated during the motor running.

I12769
1 2
3
5
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE-79
1683 Author
: Date
:
2001 AVALON (RM808U)
(d) Reverse the polarity and check that pulse is generated.
If operation is not as specified, replace the motor.
NOTICE:
If connecting the wire harness wrongly, the sensor might
be damaged so caution is necessary.
17. INSPECT JAM PROTECTION FUNCTION
NOTICE:
Never, ever be caught any part of your body when check-
ing.
HINT:
In case of performing resetting of the limit switch, do checking
after repeating up and down of the glass with automatic opera-
tion.
(a) Confirmation of AUTO up operation:
Confirm that the window will be fully close with AUTO up
operation.
(b) Checking of the operation of the jam protection function:
(1) Move up the window with AUTO up operation and
check that the window will go down when it touches
the handle of the hammer stetted.
(2) Confirm that the window will then stop going down
about 200 mm.
HINT:
In case of removing the glass, glass guide, regulator and etc.
be sure to perform checking of the jam protection function.
If the jam protection is not function properly, adjust power win-
dow motor reset switch and pulse switch.

BE0IH-03
I12534
Driver Side Junction Block

FL P/W, FR P/W, RL P/W, RR P/W Fuse

Power Main Relay

Body ECU
Front Power Window MotorIgnition SwitchPower Window Switch
(Passenger Door ECU)
Rear Power Window Motor
Power Window Master Switch
(Driver Door ECU)
Rear Power Window Switch
BE-72
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1676 Author
: Date
:
2001 AVALON (RM808U)
LOCATION

BE02C-1 1
The window moves down during the up operation.1
With ignition switch ON, when performing the auto-up operation,
if the factor which increases the sliding resistance of window
glass near the inverse position is recognized.
Disassemble the door and replace or repair the
component.
Reset the limit switch.
If power window regulator and motor operate smoothly.
Ye s
No
Check or repair door glass run and window guide
frame.
Replace the driver door control ECU with the normal one
removed from another seat. Sliding resistance check:
Power window motor reset:
Check operation power window control is normal.
Remove power window regulator assembly.
When raising the assembled window glass by hand if the glass slides
smoothly without being caught.
Ye s Sliding resistance check:
Unit check:
Install power window regulator and reset the limit switch.
Power window motor reset: *1
Check operation power window control is normal.
Power window motor faulty.
Ye s
No
Normal.
(After checking the operation repeatedly, perform the
function check.)
No
Driver door control ECU faulty.Ye s
No
HINT: When difference of descending time comparing
to the opposite window is recognized, there seems to
be an error on sliding components (door glass run
and window regulator.)
BE-70
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
1674 Author
: Date
:
2001 AVALON (RM808U)
POWER WINDOW CONTROL SYSTEM
TROUBLESHOOTING

2The DOWN function does not work though some other objects are caught in the power window glass.
Is the system in the jam protection function operating
condition?

The AUTO UP operation works with the ignition
switch ON. (One-touch operation)Normal (Perform function check)
Normal
(After performing operation check repeatedly,
conduct the function check.) Is the power window outside the jam protection func-
tion operating area?
< Out of the operating area >
Area around the fully closed position
Reset the limit switch.
*2
Does the power window operate normally?
Master switch defective.No
Ye s
Ye s
No No Ye s
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE-71
1675 Author
: Date
:
2001 AVALON (RM808U)

BE-6
- BODY ELECTRICALTROUBLESHOOTING
1610 Author
: Date
:
2001 AVALON (RM808U) Shift indicator lights do not light up.
1. Bulb
2. Park/Neutral Position Switch
3. Meter Circuit Plate
4. Wire Harness-
DI-199
BE-43
-
Only one shift indicator does not light up.1. Bulb
2. Meter Circuit Plate-
BE-43
Malfunction indicator light does not light up.
1. Bulb
2. ECM
3. Meter Circuit Plate
4. Wire Harness-
DI-1
BE-43
-
SLIP indicator light does not light up.
1. Bulb
2. ABS & TRAC ECU
3. Meter Circuit Plate
4. Wire Harness-
DI-250
BE-43
-
TRAC OFF indicator light does not light up.
1. Bulb
2. ABS & TRAC ECU
3. Meter Circuit Plate
4. Wire Harness-
DI-250
BE-43
-
Security indicator light does not light up.
1. LED
2. Theft Deterrent ECU
3. Meter Circuit Plate
4. Wire Harness-
DI-517
BE-43
-
Indicator lights do not light up. (Except Turn, Hi-beam and
security)1. GAUGE Fuse
2. Wire Harness-
-
DEFOGGER SYSTEM:
SymptomSuspect AreaSee page
All defogger systems do not operate.
1. SEAT HEATER Fuse
2. DEF Fuse
3. Defogger Relay
4. Defogger Switch
5. Wire Harness-
-
BE-67
DI-1
-
Rear window defogger does not operate.
1. Defogger Wire
2. Choke Coil
3. Wire HarnessBE-67
-
-
Mirror defogger does not operate.
1. MIR/HTR Fuse
2. Mirror Defogger
3. Wire Harness-
BE-67
-
POWER WINDOW CONTROL SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.
POWER DOOR LOCK CONTROL SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before checking the body control system.

BO2OO-01
H12112
Rear Lower FrameDoor Lock Striker23 (230, 17)
Front Door Weatherstrip
Door Glass Run
Outside Rear View
Mirror
Door Glass
Lower Frame
Bracket Garnish
7.8 (80, 69 in.´lbf)25 (260, 19)
5.4 (55, 48 in.´lbf)
Outside Handle
Key Cylinder
5.4 (55, 48 in.´lbf)
Door
Hinge
7.8 (80, 69 in.´lbf)
Door Check
25 (260, 19)
Door Speaker BoardFront Lower
Frame
25 (260, 19)
Door Hinge
Front Door Outside Lower Moulding
Door Lock Protector
Service Hole Cover
5.4 (55, 48 in.´lbf)

Precoated part
Door LockInside Handle
4.9 (50, 43 in.´lbf)
Inside Handle
Bezel
Cover
Door TrimUpper Armrest
Base Panel
Power Window Switch
Front Door Armrest
Courtesy Light
Front Door
Belt Moulding Front Door
Inner Weatherstrip
x10
5.4 (55, 48 in.´lbf)
Window Regulator
Guide Assembly
5.4 (55, 48 in.´lbf)
x8
x4
Window Regulator Motor
No. 2 Service Hole Cover
Front Door Trim Pocket : Specified torqueN´m (kgf´cm, ft´lbf)
BO-8
- BODYFRONT DOOR
1793 Author
: Date
:
2001 AVALON (RM808U)
FRONT DOOR
COMPONENTS

BO2OP-01
H04751
H12102
H12103
H12137
x10
x8
- BODYFRONT DOOR
BO-9
1794 Author
: Date
:
2001 AVALON (RM808U)
DISASSEMBLY
1. REMOVE INSIDE HANDLE BEZEL
(a) Using a screwdriver, remove the cover.
HINT:
Tape the screwdriver tip before use.
(b) Remove the screw.
(c) Using a screwdriver, remove the inside handle bezel as
shown in the illustration.
HINT:
Tape the screwdriver tip before use.
2. REMOVE COURTESY LIGHT
3. REMOVE UPPER ARMREST BASE PANEL WITH
POWER WINDOW SWITCH
(a) Using a screwdriver, remove the upper armrest base pan-
el with power window switch.
HINT:
Tape the screwdriver tip before use.
(b) Disconnect the connector.
(c) Remove the 3 screws and power window switch from the
upper armrest base panel.
4. REMOVE DOOR TRIM
(a) Using a screwdriver, remove the 2 caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 6 screws and clip.
(c) Pull the trim upward to remove it.
(d) Using a screwdriver, remove the front door inner weather-
strip from the front door trim.
(e) Remove the 10 screws and front door armrest from the
front door trim.
(f) Remove the 8 screws and front door trim pocket from the
front door trim.