2001 SUBARU LEGACY Owners Manual

Climate control4-3
–
CONTINUED –

Air flow section
HB5006CA
HB5006BA
HB5006EA
HB5006DA
HB5006FA

4-4
Manual heating and air conditioning system
Control panel
HB5004BC
1. Temp erature c ontrol d ial
2. Fan sp eed c ontrol d ial
3. Air flow c ontrol d ial
4. Air c ond itioner b utton (if eq uip p ed )
5. Air inlet selec tion b utton
6. Rear wind ow d efog g er b utton (Refer to “Rear wind ow d efog g er ” in
c hap ter 3.) n Temperature control dial
This d ial reg ulates the temp erature of air flow fro m the air outlets over
a rang e from the b lue area (c ool) to red area (warm ).
n Fan speed control dial
The fan op erates only when the ig nition switc h is t urned to the “ON ”
p osition. The fan sp eed c ontrol d ial is used to sel ec t four fan sp eed s.
n Air flow control dial
This d ial has the following five p ositions:
: Air flows throug h the instrument p anel outlets.
: Air flows throug h the instrument p anel outlets and the foot
outlets.

Climate control4-5
–
CONTINUED –
: Air flows throug h the foot outlets and some throug
h the wind -
shield d efroster outlets.
: Air flows throug h the wind shield d efroster outlets and foot
outlets.
: Air flows throug h the wind shield d efroster outlets .
n Air conditioner button (if equipped)
HB5010BB
The air c ond itioner op erates only when the eng ine i s running .
Push the air c ond itioner b utton while the fan is in op eration to turn on
the air c ond itioner. The ind ic ator lig ht will c ome on.
Push it ag ain to turn off the air c ond itioner. n Air inlet selection button
WARNING
Continued operation in the ON position may fog up the windows.
Switch to the OFF position as soon as the outside dusty condi-tion clears.

4-6
HB5008BB
ON position: Interior air is rec irc ulated insid e the vehic le. P ush the air
inlet selec tion b utton to the ON p osition. The ind i c ator lig ht will c ome
on. OFF position: Outsid e air is d rawn into the p asseng er c omp artmen t.
Push the air inlet selec tion b utton ag ain to the OF F p osition. The ind i-
c ator lig ht will g o off.
Heater operation Defrosting or defogging the windshield
HB5011AA
To d irec t warm air to the wind shield and front d oor wind ows:
1. Set the air inlet selec tion b utton to the “OFF ” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Turn the temp erature c ontrol d ial all the way to the rig ht.

Climate control4-7
–
CONTINUED –
4. Set the fan sp eed c ontrol d ial to the hig hest sp e
ed .
NOTE
Warm air also comes out from the right and left air outlets. To
stop warm air flow from these outlets, turn the correspondingthumb-wheel to the “
” position.
Heating and defrosting
HB5012AA
To d irec t warm air toward the floor and the wind shi eld :
1. Set the air inlet selec tion b utton to the “OFF ” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Set the temp erature c ontrol d ial to the most c omf ortab le level.
4. Set the fan sp eed c ontrol d ial to the d esired sp e ed .
NOTE
Warm air also comes out from the right and left air outlets. To
stop warm air flow from these outlets, turn the correspondingthumb-wheel to the “
” position.

4-8
Heating
HB5013AA
To d irec t warm air toward the floor:
1. Set the air inlet selec tion b utton to the “OFF ” p osition
2 Set the air flow c ontrol d ial to the “
” p osition.
3. Set the temp erature c ontrol d ial to the most c omf ortab le level.
4. Set the fan sp eed c ontrol d ial to the d esired sp e ed .
NOTE
Warm air also comes out from the right and left air outlets. To
stop warm air flow from these outlets, turn the correspondingthumb-wheel to the “
” position.
Bi-level heating
HB5014AA
This setting allows you to d irec t air of d ifferent temp eratures from the

Climate control4-9
–
CONTINUED –
instrument p anel and foot outlets. The air from the
foot outlets is
slig htly warmer than from the instrument p anel outl ets.
1. Set the air inlet selec tion b utton to the “OFF ” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Set the temp erature c ontrol d ial to the d esired t emp erature level.
4. Set the fan sp eed c ontrol d ial to the d esired sp e ed .
Setting the temp erature c ontrol d ial fully turned t o the red area or b lue
area d ec reases the temp erature d ifferenc e b etween t he air from the
instrument p anel outlets and the air from the foot outlets.
Ventilation
WARNING
Continued operaton in the “ON” position may fog up the win-
dows. Switch to the “OFF” position as soon as the outside dusty
condition clears.
HB5015AA
To forc e outsid e air throug h the instrument p anel o utlets:
1. Set the air inlet selec tion b utton to the “OFF ” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Set the temp erature c ontrol d ial all the way left .
4. Set the fan sp eed c ontrol d ial to the d esired sp e ed .
When d riving on a d usty road , set the air inlet c on trol lever to the “ON ”
p osition.

4-10
Air conditioner operation Cooling or dehumidifying
HB5016BB
For c ooling and d ehumid ific ation of the p asseng er c omp artment, air
flows throug h the instrument p anel outlets:
1. Set the air inlet selec tion b utton to the “OFF ” p osition.
2. Set the air flow c ontrol d ial to the “
” p osition.
3. Set the air c ond itioner b utton to the “ON ” p osition.
4. Set the temp erature c ontrol d ial to the b lue area .
5. Set the fan sp eed c ontrol d ial at the hig hest sp e ed .
Defrosting or defogging
HB5011BB
To d irec t warm air to the wind shield and front d oor wind ows:
1. Set the air inlet selec tion b utton to the “OFF ” p osition.