2001 SUBARU LEGACY mirror controls

Instruments and controls3-31
–
CONTINUED –
The wind shield wip er d eic er op erates only when the
ig nition switc h is in
the “ON ” p osition.
Before turning on the wind shield wip er d eic er, remo ve any snow from the
wind shield . To turn on the wind shield wip er d eic er, p ush the switc h. The
ind ic ator lig ht loc ated on the switc h lig hts up whi le the wind shield wip er
d eic er is op erating .
The wind shield wip er d eic er will automatic ally shut off after ab out 15 min-
utes. If the wip er b lad es have b een d eic ed c omp lete ly b efore that time,
p ush the switc h to turn it off. It also turns off w hen the ig nition switc h is
turned to the “ACC ” or “LOCK ” p osition. If d eic ing is not c omp lete when
you restart your vehic le, you have to p ush the swit c h to turn the d eic er
on ag ain. Mirrors
Always c hec k that the insid e and outsid e mirrors ar e p rop erly ad justed
b efore you start d riving . Inside mirror
HB4003BB
The insid e mirror has a d ay and nig ht p osition. Pul l the tab at the b ottom
of the mirror toward you for the nig ht p osition. Pu sh it away for the d ay
p osition. The nig ht p osition red uc es g lare from hea d lig hts.

Instruments and controls3-33
–
CONTINUED –
n
Photosensors
HB6020BA
The mirror has a p hotosensor attac hed on b oth the f ront and b ac k
sid es. If the g lare from the head lig hts of vehic les b ehind you strikes
the mirror, these sensors d etec t it and make the re flec tion surfac e of
the mirror d immer to help p revent you from b eing b l ind ed . For this
reason, use c are not to c over the sensors with stic kers, or other simi-
lar items. Period ic ally wip e the sensors c lean usin g a p iec e of d ry soft
c otton c loth or an ap p lic ator. n Compass calibration
1. For op timum c alib ration, switc h off all nonessent ial elec tric al ac -
c essories (rear wind ow d efog g er, heater/air c ond iti oning system,
sp otlig ht, etc .) and ensure all d oors are shut.
2. Drive to an op en, level area away from larg e meta llic ob jec ts or
struc tures and make c ertain the ig nition switc h is in the “ON ” p osition.
3. Press and hold the left b utton for 3 sec ond s then release, and the
c omp ass will enter the c alib ration mod e. “CAL ” and d irec tion will b e
d isp layed .
4. Drive slowly in a c irc le until “CAL ” d isap p ears from the d isp lay
(ab out two or three c irc les).
5. The c omp ass is now c alib rated . Further c alib ratio n is not req uired .
The c omp ass will automatic ally c alib rate from this p oint forward .

Instruments and controls3-35
–
CONTINUED –

Adjusting mirrors
To ad just the mirrors b y hand , p ush where ind ic ated b y the arrows.
OM-H2737
Remote control mirror switch (if equipped)
The remote c ontrol mirrors op erate only when the ig nition switc h is in
the “ON ” or “ACC ” p osition.
HB4004BB
1. Press either end of the selec tion switc h, “L ” for the left, “R ” for the
rig ht.
2. Move the d irec tion c ontrol switc h in the d irec tio n you want to move
the mirror.
3. Return the selec tion switc h to the neutral p ositi on to p revent
unintentional op eration.
The mirrors c an also b e ad justed manually.