2001 NISSAN X-TRAIL Nats system

EC-46
[QR25(WITH EURO-OBD)]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
*1: 1st trip DTC No. is the same as DTC No.P0500 0500
VEH SPEED SEN/CIRC*
7——×EC-250
P0550 0550 PW ST P SEN/CIRC — —×EC-255
P0605 0605 ECM — —×EC-260
P0650 0650 MIL/CIRC — —×EC-263
P0705 0705 PNP SW/CIRC — —×AT- 11 0
P0710 0710 ATF TEMP SEN/CIRC — —×AT- 11 6
P0720 0720
VEH SPD SEN/CIR AT*7——×AT-122
P0731 0731 A/T 1ST GR FNCTN — —×AT-131
P0732 0732 A/T 2ND GR FNCTN — —×AT-137
P0733 0733 A/T 3RD GR FNCTN — —×AT-143
P0734 0734 A/T 4TH GR FNCTN — —×AT-149
P0740 0740 TCC SOLENOID/CIRC — —×AT-158
P0745 0745 L/PRESS SOL/CIRC — —×AT-163
P0750 0750 SFT SOL A/CIRC — — —AT- 1 7 0
P0755 0755 SFT SOL B/CIRC — — —AT- 1 7 5
P1065 1065 ECM BACK UP/CIRC — —×EC-267
P 1111 1111 I N T / V T I M V / C I R - B 1 — —×EC-271
P1121 1121 ETC ACTR — —×EC-276
P1122 1122 ETC FUNCTION/CIRC — —×EC-278
P1124 1124 ETC MOT PWR — — —EC-285
P1126 1126 ETC MOT PWR — — —EC-285
P1128 1128 ETC MOT — — —EC-290
P1143 1143 HO2S1 (B1) — —
×*4EC-295
P1144 1144 HO2S1 (B1) — —
×*4EC-301
P1146 1146 HO2S2 (B1) — —
×*4EC-307
P1147 1147 HO2S2 (B1) — —
×*4EC-315
P1217 1217 ENG OVER TEMP — — —EC-323
P1225 1225 CTP LEARNING — —×EC-337
P1226 1226 CTP LEARNING — —×EC-339
P1229 1229 SENSOR POWER/CIRC — — —EC-341
P1610 - P1615 1610 - 1615 NATS MALFUNCTION — —×EC-58
P1705 1705 TP SEN/CIRC A/T — — —AT- 1 8 0
P1706 1706 P-N POS SW/CIRCUIT — —×EC-345
P1760 1760 O/R CLTCH SOL/CIRC — —×AT-185
P1805 1805 BRAKE SW/CIRCUIT — —×EC-349
P2122 2122 APP SEN 1/CIRC — — —EC-355
P2123 2123 APP SEN 1/CIRC — — —EC-355
P2127 2127 APP SEN 2/CIRC — — —EC-361
P2128 2128 APP SEN 2/CIRC — — —EC-361
P2135 2135 TP SENSOR — — —EC-367
P2138 2138 APP SENSOR — — —EC-373
DTC*1
Items
(CONSULT-II screen terms)SRT codeTest value/
Te s t l i m i t
(GST only)1st trip
DTC*1Reference page
CONSULT-II
GST*
2ECM*3

EC-58
[QR25(WITH EURO-OBD)]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
5. System readiness test (SRT) codes
6. Test values
7. Others
Actual work procedures are explained using a DTC as an example. Be careful so that not only the DTC, but all
of the data listed above, are cleared from the ECM memory during work procedures.
NATS (Nissan Anti-theft System)EBS00M0P
●If the security indicator lights up with the ignition switch in
the “ON” position or “NATS MALFUNCTION” is displayed
on “SELF-DIAG RESULTS” screen, perform self-diagnostic
results mode with CONSULT-II using NATS program card.
Refer to BL-80, "
NATS (NISSAN ANTI-THEFT SYSTEM)" .
●Confirm no self-diagnostic results of NATS is displayed
before touching “ERASE” in “SELF-DIAG RESULTS” mode
with CONSULT-II.
●When replacing ECM, initialization of NATS system and reg-
istration of all NATS ignition key IDs must be carried out
with CONSULT-II using NATS program card.
Therefore, be sure to receive all keys from vehicle owner.
Regarding the procedures of NATS initialization and NATS ignition key ID registration, refer to
CONSULT-II operation manual, NATS.
Malfunction Indicator (MI)EBS00M0Q
DESCRIPTION
The MI is located on the instrument panel.
1. The MI will light up when the ignition switch is turned ON without
the engine running. This is a bulb check.
●If the MI does not light up, refer to DI-43, "WARNING LAMPS" ,
or see EC-263
.
2. When the engine is started, the MI should go off.
If the MI remains on, the on board diagnostic system has
detected an engine system malfunction.
ON BOARD DIAGNOSTIC SYSTEM FUNCTION
The on board diagnostic system has the following four functions.
SEF515Y
SAT652J
Diagnostic Test
ModeKEY and ENG.
Sta tusFunction Explanation of Function
Mode I Ignition switch in
“ON” position
Engine stoppedBULB CHECK This function checks the MI bulb for damage (blown, open
circuit, etc.).
If the MI does not come on, check MI circuit.
Engine running MALFUNCTION
WARNINGThis is a usual driving condition. When a malfunction is
detected twice in two consecutive driving cycles (two trip
detection logic), the MI will light up to inform the driver that
a malfunction has been detected.
The following malfunctions will light up or blink the MI in
the 1st trip.
●“Misfire (Possible three way catalyst damage)”
●“One trip detection diagnoses”

TROUBLE DIAGNOSIS
EC-75
[QR25(WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
6.PERFORM IDLE AIR VOLUME LEARNING
Refer to EC-39, "
Idle Air Volume Learning" .
Is Idle Air Volume Learning carried out successfully?
Ye s o r N o
Ye s > > G O T O 7 .
No >> 1. Follow the Instruction of “Idle Air Volume Learning”.
2. GO TO 4.
7.CHECK TARGET IDLE SPEED AGAIN
With CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Read idle speed in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.
OK or NG
OK >> GO TO 10.
NG >> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the Following.
●Check camshaft position sensor (PHASE) and circuit. Refer to EC-233 .
●Check crankshaft position sensor (POS) and circuit. Refer to EC-227 .
OK or NG
OK >> GO TO 9.
NG >> 1. Repair or replace.
2. GO TO 4.
9.CHECK ECM FUNCTION
1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is the rarely the case.)
2. Perform initialization of NATS system and registration of NATS ignition key IDs. Refer to EC-58, "
NATS
(Nissan Anti-theft System)" .
>> GO TO 4.
10.CHECK IGNITION TIMING
1. Run engine at idle.
2. Check ignition timing with a timing light.
OK or NG
OK >>INSPECTION END
NG >> GO TO 11.M/T: 700 ± 50 rpm
A/T: 700 ± 50 rpm (in “P” or “N” position)
M/T: 700 ± 50 rpm
A/T: 700 ± 50 rpm (in “P” or “N” position)
M/T: 15 ± 5° BTDC
A/T: 15 ± 5° BTDC (in “P” or “N” position)

TROUBLE DIAGNOSIS
EC-77
[QR25(WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
16.CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Refer to EM-37, "
TIMING CHAIN" .
OK or NG
OK >> GO TO 17.
NG >> 1. Repair the timing chain installation.
2. GO TO 4.
17.DETECT MALFUNCTIONING PART
Check the following.
●Check camshaft position sensor (PHASE) and circuit. Refer to EC-233 .
●Check crankshaft position sensor (POS) and circuit. Refer to EC-227 .
OK or NG
OK >> GO TO 18.
NG >> 1. Repair or replace.
2. GO TO 4.
18.CHECK ECM FUNCTION
1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is the rarely the case.)
2. Perform initialization of NATS system and registration of NATS ignition key IDs. Refer to EC-58, "
NATS
(Nissan Anti-theft System)" .
>> GO TO 4.
Symptom Matrix ChartEBS00M0W
SYSTEM — BASIC ENGINE CONTROL SYSTEM
SYMPTOM
Reference
page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA
Fuel Fuel pump circuit 11232 22 3 2EC-405
Fuel pressure regulator system334444444 4EC-42
Injector circuit 11232 22 2EC-388
Evaporative emission system334444444 4EC-425

EC-80
[QR25(WITH EURO-OBD)]
TROUBLE DIAGNOSIS
1 - 6: The numbers refer to the order of inspection.Va l v e
mecha-
nismTiming chain
55555 55 5EM-37
CamshaftEM-46
Intake valve
3EM-59
Exhaust valve
Exhaust Exhaust manifold/Tube/Muffler/
Gasket
55555 55 5EM-24
,EX-
2Three way catalyst
Lubrica-
tionOil pan/Oil strainer/Oil pump/Oil
filter/Oil gallery/Oil cooler
55555 55 52EM-26
,LU-
9 , LU-10 ,
LU-13
Oil level (Low)/Filthy oilLU-7
Cooling Radiator/Hose/Radiator filler cap
55555 55 25CO-11
Thermostat 5CO-20
Water pumpCO-18
Water galleryCO-7
Cooling fan 5CO-11
Coolant level (low)/Contaminated
coolantCO-9
NATS (Nissan Anti-theft System) 1 1EC-58 or
BL-80
SYMPTOM
Reference
page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA

EC-262
[QR25(WITH EURO-OBD)]
DTC P0605 ECM
2. REPLACE ECM
1. Replace ECM.
2. Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to EC-58, "
NATS
(Nissan Anti-theft System)" .
3. Perform EC-39, "
Accelerator Pedal Released Position Learning" .
4. Perform EC-39, "
Throttle Valve Closed Position Learning" .
5. Perform EC-39, "
Idle Air Volume Learning" .
>>INSPECTION END

EC-270
[QR25(WITH EURO-OBD)]
DTC P1065 ECM POWER SUPPLY
5. REPLACE ECM
1. Replace ECM.
2. Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to EC-58, "
NATS
(Nissan Anti-theft System)" .
3. Perform EC-39, "
Throttle Valve Closed Position Learning" .
4. Perform EC-39, "
Idle Air Volume Learning" .
>>INSPECTION END

EC-432
[QR25(WITHOUT EURO-OBD)]
INDEX FOR DTC
[QR25(WITHOUT EURO-OBD)]INDEX FOR DTCPFP:00024
Alphabetical IndexEBS00NC2
Check if the vehicle is a model with Euro-OBD (E-OBD) system or not by the “Type approval number” on the
identification plate. Refer to GI-43, "
IDENTIFICATION PLATE" .
NOTE:
If DTC U1000 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000. Refer to
EC-513
.
×: Applicable –: Not applicable
Items
(CONSULT-II screen terms)DTC*
1
TripMI lighting
upReference page
CONSULT-II
ECM*2
APP SENSOR P2138 2138 2×EC-651
APP SEN 1/CIRC P2122 2122 1×EC-631
APP SEN 1/CIRC P2123 2123 1×EC-631
APP SEN 2/CIRC P2127 2127 1×EC-637
APP SEN 2/CIRC P2128 2128 1×EC-637
BRAKE SW/CIRCUIT P1805 1805 2 –EC-625
CAN COMM CIRCUIT*5U1000
1000*41×EC-513
CKP SEN/CIRCUIT P0335 0335 2×EC-551
CMP SEN/CIRCUIT P0340 0340 2×EC-557
CTP LEARNING P1225 1225 2 —EC-617
CTP LEARNING P1226 1226 2 —EC-619
ECM P0605 0605 1 or 2× or –EC-573
ECM BACK UP/CIRC P1065 1065 2×EC-580
ECT SEN/CIRCUIT P0117 0117 1×EC-523
ECT SEN/CIRCUIT P0118 0118 1×EC-523
ENG OVER TEMP P1217 1217 1×EC-603
ETC ACTR P1121 1121 1 or 2×EC-584
ETC FUNCTION/CIRC P1122 1122 1×EC-586
ETC MOT P1128 1128 1×EC-598
ETC MOT PWR P1124 1124 1×EC-593
ETC MOT PWR P1126 1126 1×EC-593
HO2S1 (B1) P0134 0134 2×EC-534
HO2S2 (B1) P0138 0138 2×EC-185
HO2S2 (B1) P0139 0139 2×EC-192
MAF SEN/CIRCUIT P0102 0102 1×EC-516
MAF SEN/CIRCUIT P0103 0103 1×EC-516
MIL/CIRC P0650 0650 1 or 2× or –EC-576
NATS MALFUNCTION P1610 - P1615 1610 - 1615 2 –EC-58
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.No DTC
Flashing*3–
Flashing*3EC-59
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000––—
PW ST P SEN/CIRC P0550 0550 2 –EC-568
SENSOR POWER/CIRC P1229 1229 1×EC-621
TP SEN 2/CIRC P0122 0122 1×EC-528