2001 Lexus ES300 Owner's Manuals (in English)

COMFORT ADJUSTMENT
2001. Sit the child on a booster seat. Run the lap and
shoulder belt through or around the booster seat and
child following the instructions provided by its
manufacturer and insert the tab into the buckle.
Make sure the shoulder belt is correctly across the
child's
shoulder and that the lap belt is positioned as low
as possible on child's hips. See ªSeat beltsº on page 136
for details.
CAUTION
 Always make sure the shoulder belt is positioned
across the center of child's shoulder. The b elt should
be kept away from child's neck, but not falling off
child's shoulder. Failure to do so could reduce the
amount of protection in an accident and cause
serious injuries in a collision.
 Both high±positioned lap belts and
loose±fitting belts could cause serious injuries
due to sliding under the lap belt during a
collision or other unintended result. Keep the
lap belt positioned as low on a child's hips as
possible.
 For child's safety, do not place the shoulder
belt under child's arm.
 After inserting the tab, make sure the tab and
buckle are l ocked and that the lap and shoulder
portions of the belt are not twisted.
 Do not insert coins, clips, etc. in the buckle as
this may prevent your child from properly
latching the tab and buckle.
 If the seat belt does not function normally,
immediately contact your Lexus dealer. Do not
use the seat until the seat belt is fixed. It cannot
protect your child from injury.

COMFORT ADJUSTMENT
201
16E117c
2. To remove the child restraint system, press the
buckle±release button and allow the belt to retract.Using a top strap
16E219
Follow the procedure below for a child restraint
system that requires the use of a top strap.

COMFORT ADJUSTMENT
202
16E248

Anchor bracket
Use the anchor bracket on the package tray behind the
rear seat to attach the top strap.
Anchor brackets are installed for each rear seating
position.

COMFORT ADJUSTMENT
203
16E211
Fix the child restraint system with the seat belt.
Latch the hook onto the anchor bracket and tighten
the top strap.
For instructions to install the child restraint system, see
ªChild restraint systemº on page 178.
CAUTION
Make sure the top strap is securely latched, and check
that the child restraint system is securely by pushing
and pulling it in different directions. Follow all the
installation instructions provided by its manufacturer.

COMFORT ADJUSTMENT
204
DRIVING POSITION MEMORYSYSTEM
The micro computer can memorize the positions of the
driver's seat and outside rear view mirrors. Two dif ferent
driving position profiles can be entered into the
computer's memory.
Recording a driving position in the computer's memory
can only be done when the ignition key is in the ªONº
position and the selector lever is in the ªPº position.
Setting a driving position
16E047

COMFORT ADJUSTMENT
205
1. Adjust the driver's seat and outside rear view
mirrors to the desired position.
2. While
pushing the ªSETº button, push button ª1º
or ª2º until the signal beeps.
The beep sound means that the positions are recorded
in the computer's memory. By repeating these two steps and pressing the
remaining button, the driving position for another driver
can be recorded.
To set a new memorized position, select the desired
position and perform step 2. The previous memory will
be erased and the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the
memorized position, then make the desired changes
and perform step 2 above.

COMFORT ADJUSTMENT
206
Activating a memorized position
16E048
When you push button ª1º or ª2º, the driving
position will be automatically adjusted to the
position recorded for that button.

COMFORT ADJUSTMENT
207
Conditions for memorized position activation

Ignition key ªONº and selector lever in ªPº position
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the
seat position will not change.
 Key not in ignition switch and within 30 seconds of
opening driver's door.
The memorized position can be activated.
If any driving position memory switch is pushed while
one of the memorized driving position profiles is being
activated, the operation will stop.
To activate the system, push the desired button (ª1º or
ª2º) again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle's battery is disconnected, the computer's
memory will be erased and the memorized positions will
have to be set again.