2001 Lexus ES300 Owner's Manuals (in English)

INTERIOR EQUIPMENT
88
GARAGE DOOR OPENER
The garage door opener (HomeLinkUniversal
Transceiver) is manufactured under license from
HomeLink
 and can be programmed to operate
garage doors, gates, entry doors, door locks, home
lighting systems, and security systems, etc.
(a) Programming the HomeLink
14E065
 1Indicator light 2 Buttons
The HomeLink in your vehicle has 3 buttons and
you can store one program for each button.
To ensure correct programming into the HomeLink
,
install a new battery in the hand±held transmitter prior to
programming.

INTERIOR EQUIPMENT
89
The battery side of the hand±held transmitter must be
pointed away from the HomeLink
 during the
programming process.
For Canadian users, follow the procedure in
ªProgramming an entrance gate/Programming all
devices in the Canadian marketº.
1. Decide which of 3 HomeLink
 buttons you want to
program.
2. Place your hand±held garage transmitter 25 to 75
mm (1 to 3 in.) away from the surface of the HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Simultaneously press and hold the hand±held garage
transmitter button along with the selected HomeLink

button.
4. When the indicator light on the HomeLink
 changes
from a slow to a rapid flash after 20 seconds, you can
release both buttons.
5. Test the operation of the HomeLink
 by pressing the
newly programmed button. If programming a garage
door opener, check to see if the garage door opens and
closes. If the garage door does not operate, identify if your
garage transmitter is of the ªRolling Codeº type. Press
and hold the programmed HomeLink
 button. The
garage door has the rolling code feature if the indicator
light (on the HomeLink
) flashes rapidly and then
remains lit after 2 seconds. If your garage transmitter is
the ªRolling Codeº type, proceed to the heading
ªProgramming a rolling code systemº.
6. Repeat steps 2 through 5 for each remaining
HomeLink
 button to program another device.
Programming a rolling code system
If your device is ªRolling Codeº equipped, it is
necessary to follow steps 1 through 4 under the
heading ªProgramming the HomeLink
º before
proceeding with the steps listed below.
1. Locate the ªtrainingº button on the ceiling mounted
garage door opener motor. The exact location and color
of the button may vary by brand of garage door opener.
Refer to the owner's guide supplied by the garage door
opener manufacturer for the location of this ªtrainingº
button.
2. Press the ªtrainingº button on the ceiling mounted
garage door opener motor.
Following this step, you have 30 seconds in which to
initiate step 3 below.

INTERIOR EQUIPMENT
903. Press and release the vehicle's programmed
HomeLink
 button twice. The garage door may open.
If the door does open, the programming process is
complete. If the door does not open, press and release
the button a third time. This third press and release will
complete the programming process by opening the
garage door.
The ceiling mounted garage door opener motor should
now recognize the HomeLink
 unit and be able activate
the garage door up/down.
4. Repeat steps 1 through 3 for each remaining
HomeLink
 button to program another rolling code
system.
Programming an entrance gate /
Programming all devices in the Canadian
market
1. Decide which of the 3 HomeLink buttons you want
to program.
2. Place your hand±held gate/device transmitter 25 to
75 mm (1 to 3 in.) away from the surface of the
HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Press and hold the selected HomeLink
 button.
4. Continuously press and release (cycle) the
hand±held gate/device transmitter button every two seconds until step 5 is complete.
5. When the indicator light on the HomeLink
 changes
from a slow to a rapid flash after 20 seconds, you can
release both buttons.

INTERIOR EQUIPMENT
91
6. Test the operation of the HomeLink
 by pressing the
newly programmed button. Check to see if the
gate/device operates correctly.
7. Repeat steps 1 through 6 for each remaining
HomeLink
 button to program another device.
Programming other devices
To program other devices such as home security
systems, home door locks or lighting, contact your
authorized Lexus dealer for assistance.
Reprogramming a button
Individual HomeLink buttons cannot be erased,
however, to reprogram a single button, follow the
procedure ªProgramming the HomeLink
º.
(b) Operating the HomeLink
To operate the HomeLink, press the appropriate
HomeLink button to activate the programmed device.
The HomeLink indicator light should come on. The
HomeLink continues to send the signal for up to 20
seconds as long as the button is pressed.
(c) Erasing the entire HomeLink
memory (all three programs)
To erase all previously programmed codes at one time,
press and hold down the 2 outside buttons for 20
seconds until the indicator light flashes.
If you sell your vehicle, be sure to erase the programs
stored in the HomeLink
 memory.

INTERIOR EQUIPMENT
92
CAUTION
When programming the HomeLink Universal
Transceiver, you may be operating a garage door or
other device. Make sure people and objects are out
of the way of the garage door or other device to
prevent potential harm or damage.
 Do not use this HomeLink
 Universal Transceiver
with any garage door opener that lacks the safety
stop and reverse feature as required by federal safety
standards. (This includes any garage door opener
model manufactured before April 1, 1982.) A garage
door opener, which cannot detect an object,
signaling the door to stop and reverse, does not meet
current federal safety standards. Using a garage
door opener without these features increases risk of
serious injury or death.

INTERIOR EQUIPMENT
93
FCC ID: CB2V94800
CANADA: 1763 102 264
This device complies with FCC Rules Part 15.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference that may be received,
including interference that may cause undesired
operation. WARNING: This transmitter has
been tested and complies with FCC and
DOC/MDC rules. Changes or modifications
not expressly approved by the party
responsible for compliance could void the
user's authority to operate the device.
CUP HOLDER
14E010
Front cup holder
To use the front cup holder, push the top of the cup
holder portion of the console box.

INTERIOR EQUIPMENT
94
14E011±2
Rear cup holder
To use the rear cup holder, pull the cup holder
portion of the console box.
The cup holder is designed for holding cups or
drink±cans securely.
CAUTION
Do not place anything else other than cups or
drink±cans on the cup holder, as such items may be
thrown about in the compartment and possibly injure
people in the vehicle during sudden braking or in an
accident.
 To reduce the chance of injury in case of an accident
or sudden stop while driving, keep the cup holder
closed when not in use.

INTERIOR EQUIPMENT
95
OVERHEAD CONSOLE BOX
14E051
To use the box, open it as shown above.
CAUTION
To reduce the chance of injury in case of an accident
or a sudden stop, always keep the overhead console
box closed while driving.
 As this box is designed for holding eyeglasses, do
not place any object heavier than approximately 60 g
(0.13 lb.) in it. Heavier objects may cause the box to
open and contents to fly out resulting in injuries.