
INTERIOR TRIM COMPONENTS
76-3-22 REPAIRS
29.Noting fitted position remove fascia harness
assembly.Refit
1.Fit and secure fascia harness.
2.Fit striker plate, secure with screws and adjust
if necessary.
3.Fit passenger side glove box assembly.
4.Fit face level air vents.
5.Fit and secure cruise switch carrier assembly to
fascia.
+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Switch - engagement
(on/off) - from 04MY.
6.Fit glove box lids and secure hinge pins.
7.Connect mirror switch multiplug and fit switch
assembly to fascia.
8.Fit switches to fascia carrier and connect
multiplugs.
9.With assistance fit fascia to vehicle and secure
bolts to 10 Nm (7 lbf.ft).
10.Connect fascia harness multiplugs to main
harness.
11.Fit passenger airbag.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - from 04MY.
12.Fit 'A' post upper trim finishers.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
13.Fit hazard warning switch.
+ DRIVER CONTROLS, REPAIRS,
Switch - hazard warning - from 04MY.
14.Fit clock.
+ INSTRUMENTS, REPAIRS, Clock.
15.Open drivers side glove box.
16.Fit Radio/CD module.
+ IN CAR ENTERTAINMENT,
REPAIRS, Radio/CD - from 04MY.
17.Fit fuse box cover and close glove box lid.
18.Fit steering column lower cover and secure with
screws.
19.Fit wiper/indicator switch and tighten clamping
screw.
20.Connect multiplugs to wiper/indicator switch.
21.Fit rotary coupler.
+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.
22.Fit heater control to fascia and secure with
screws.
23.Fit instrument pack.
+ INSTRUMENTS, REPAIRS,
Instrument panel - from 04MY.
M76 4721

PANEL REPAIRS
77-2-16 WELDING PROCEDURES
General Welding Precautions
General
For ease of reference, the diagrams on the following pages show only the type of weld used in repair where it varies
from that used in production.
The replacement welds in the welding diagrams are denoted by the following symbols:
a = Single/Multiple thickness plug welds
b = MIG seam weld
When carrying out welding operations the following criteria must be observed:
lWhere resistance spot welds have been used in production, these must be reproduced with new spot welds in
replacement where possible. All such reproduction spot welds must be spaced 30 mm (1.181) apart;
lWhen spot welding, it is recommended that test coupons of the same metal gauges and materials are produced
to carry out peel tests to ensure that welding equipment being used can produce a satisfactory joint. Plug welds
must be used if a satisfactory spot weld cannot be produced;
lThe electrode arms on hand-held spot welding guns must not exceed 300 mm (11.811) in length;
lSingle-side spot welding is not acceptable;
lBrazing and gas welding are not acceptable EXCEPT where they have been specified in production;
lWhere 3 metal thicknesses or more are to be welded together it is imperative to use MIG plug welds to ensure
joint strength;
lMIG plug welds must be used in repair joints where there is no access for a resistance spot welder. To replace
each production spot weld, an 8 mm (0.314) approx hole must be drilled and/or punched, and a MIG plug weld
then made in its place. The number of plug welds must match exactly the number of spot welds which have been
removed;
lWhere holes are left in an existing panel after removal of the spot welds, a single MIG plug weld will be made in
each hole as appropriate.
Electronic Control Units
The electronic control units (ECU) fitted to vehicles make it advisable to follow suitable precautions prior to carrying
out welding repair operations. Harsh conditions of heat and vibration may be generated during these operations which
could cause damage to the units.
In particular, it is essential to follow the appropriate precautions when disconnecting or removing the airbag DCU.
Equipment
Prior to commencing any test procedure on the vehicle, ensure that the relevant test equipment is working correctly
and any harness or connectors are in good condition. This particularly applies to electronic control units.

HEATING AND VENTILATION
80-8REPAIRS
9. NOTE: Models with passenger airbag,
remove carrier.Remove bolt from duct of RH
outer face level vent and release duct from
heater.
10.Release duct of RH demister vent.
11.Release duct of LH demister vent.
12.Release air inlet connector hose.
13.Release harness from 2 clips on heater.
14.Remove 2 nuts and 1 bolt securing heater to
body and remove heater.
NOTE: Do not carry out further dismantling if
component is removed for access only.15.Disconnect 2 multiplugs from heater controls.
16.Release air blend control cable from lever and
abutment.
17.Release air distribution cable from lever and
abutment.
18.Remove heater controls.

HEATING AND VENTILATION
REPAIRS 80-9
Refit
1.Position heater controls to replacement heater.
2.Connect air distribution cable to lever and
abutment.
3.Connect air blend cable to lever and abutment.
4.Connect multiplugs to heater controls.
5.Fit heater and secure with nuts and bolt.
6.Position harness and connect to clips on
heater.
7.Fit air inlet connector hose.
8.Fit RH demister vent duct to heater.
9. Models with passenger airbag, fit carrier.Fit
RH outer face level vent duct to heater and
secure to body with bolt.
10.Fit LH demister vent duct to heater.
11.Fit LH outer face level vent duct to heater and
secure to body with bolt.
12. Models with A/C: Connect multiplug to
evaporator.
13.Connect multiplug to heater and secure
diagnostic socket.
14.Connect multiplugs to heater controls.
15.Fit console support bracket and secure with
bolts.
16.Fit relays to console support bracket.
17.Fit fascia.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
18.Connect heater hoses and secure with clips.
19.Refill cooling system.
+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
+ COOLING SYSTEM - K SERIES 1.8,
ADJUSTMENTS, Coolant - drain & refill.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.

SECURITY
86-4-2 REPAIRS
Switch/push - horn
$% 86.30.01
Remove
1.Remove airbag module from steering wheel.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
2.Release horn switch multiplugs and leads from
steering wheel base.
3.Disconnect multiplug from rotary coupler.
4.Using a broad round edged tool, carefully prise
horn switch from steering wheel.
5.Noting fitted position disconnect 2 Lucars and
remove horn switch.
Refit
1.Position horn switch and connect Lucars.
2.Carefully fit horn switch to steering wheel.
3.Connect multiplug to rotary coupler.
4.Secure leads and multiplug to base of steering
wheel.
5.Fit airbag to steering wheel.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
Horn
$% 86.30.10
Remove
1.Remove bolt securing horn to body.
2.Disconnect multiplug from horn and remove
horn.
NOTE: Do not carry out further dismantling if
component is removed for access only.
3.Remove nut securing bracket to horn and
remove bracket.
Refit
1.Fit bracket to horn and secure with nut.
2.Connect multiplug to horn.
3.Fit horn to body and secure with bolt.

HARNESSES
86-7-6 REPAIRS
53.Release fuse box, disconnect 11 multiplugs
and remove fuse box.
54.Disconnect multiplug from steering column
switch.
55.Release harness clip from steering column.
56.Disconnect multiplug from throttle position
sensor.
57.Disconnect multiplugs from brake light switch
and brake pedal position switch.58.Disconnect multiplug from airbag ECU.
59.Remove airbag ECU securing bolt and release
earth lead.
60.Remove nut from earth header and release
header from floor tunnel.

HARNESSES
86-7-10 REPAIRS
90.Remove 4 screws from rear bumper lamps,
release lamps and disconnect multiplugs.
91.Release harness clips and pull harness into
luggage compartment.
92.Release main harness retaining clips and pull
harness into vehicle interior.
93.Remove main harness.Refit
1.Lay main harness in vehicle.
2.Locate rear section and secure in retaining
clips.
3.Feed harness to rear bumper lamps, secure in
clips and grommets.
4.Connect multiplugs to rear bumper lamps, fit
rear lamps and secure with screws.
5.Fit LH rear earth header and secure with nut.
6.Connect multiplugs to LH tail lamp.
7.Position RH tail lamp and connect multiplugs.
8.Fit RH tail lamp and secure with Torx screws.
9.Fit RH rear earth header and secure with nut.
10.Connect multiplug to towing electrics.
11.Connect rear screen washer tube.
12.Connect tail door harness multiplugs.
13.Connect and fit rear window lift and wash/wipe
relays.
14.Position harness into luggage compartment.
15.Connect both rear ABS speed sensor
multiplugs and secure harness grommets.
16.Connect multiplug to fuel pump.
17.Fit fuel pump access cover and secure with
screws.
18.Fit luggage compartment carpet.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
19.Connect multiplugs at the base of 'B/C' Posts.
20.Fit all harness clips to interior of vehicle.
21.Fit multiplugs and earth header to LH lower 'A'
post.
22.Fit earth header to RH lower 'A' post.
23.Connect multiplug to window lift ECU.
24.Fit face level vent ducting.
25.Fit steering column to bracket and secure with
nuts.
26.Fit rear heater ducting and secure with nut.
27.Secure harness to rear heater ducting with
clips.
28.Position mounting bracket and secure relays.
29.Connect Lucar to handbrake switch.
30. Manual gearbox only: Connect multiplug to
gear lever hill descent switch.
31.Connect multiplug to accelerometer.
32. Automatic gearbox only: Connect multiplugs
to gear selector.
33.Connect heated oxygen sensor multiplug.
34.Fit earth header to floor tunnel and secure with
nut.
35.Fit earth lead to airbag ECU and secure with
bolt.
36.Connect multiplug to airbag ECU.
37.Connect multiplugs to brake light switch and
brake pedal position switch.
38.Connect multiplug to throttle position sensor.
39.Fit harness clip to steering column.
40.Connect multiplug to steering column switch.

DRIVER CONTROLS
REPAIRS 86-8-1
DRIV ER CONTROLS REPAIRS
Switch - remote control - audio system
$% 86.50.13
Remove
1.Remove drivers airbag.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
2.Release remote control switch leads and
disconnect multiplug.
3.Remove 2 screws securing remote control
switch and remove switch.
Refit
1.Fit remote control switch and secure with
screws.
2.Connect switch multiplug and fit leads in clip.
3.Fit drivers airbag.
+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
Switch - park distance control (PDC) -
from 04 MY
$% 86.54.02
Remove
1.Release 2 clips and remove fascia mounted
switch cover.
2.Remove 2 screws securing switch carrier to
fascia.
3.Release switch carrier from fascia and
disconnect PDC multiplug.
4.Remove switch assembly from carrier.
Refit
1.Fit PDC switch to carrier.
2.Connect multiplug to PDC switch.
3.Secure switch carrier to fascia with screws.
4.Fit and secure switch cover.