2001 INFINITI QX4 engine

Diagnostic ProcedureNBAT0226
1 CHECK INPUT SIGNAL
With CONSULT-II
1. Start engine.
2. Select ªTCM INPUT SIGNALSº in ªDATA MONITORº mode for ªA/Tº with CONSULT-II.
3. Read out the value of ªTURBINE REVº. Check the value changes according to engine speed.
SAT740J
Without CONSULT-II
1. Start engine.
2. Check voltage between TCM terminal 38 and ground. (Measure in AC range.)
SAT140K
OK or NG
OK©GO TO 3.
NG©GO TO 2.
2 DETECT MALFUNCTIONING ITEM
Check harness for short or open between TCM and turbine revolution sensor.
OK or NG
OK©GO TO 3.
NG©Repair or replace damaged parts.
3 CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-203.
OK or NG
OK©INSPECTION END
NG©GO TO 4.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC TURBINE REVOLUTION SENSOR
Diagnostic Procedure
AT-205

DescriptionNBAT0228The ECM and TCM provide mutual communication in relation to
engine output control signal (ignition timing retard signal) during
rapid standing starts/acceleration. With this consistent real-time
control, the shifting feel is substantially improved.
TCM TERMINALS AND REFERENCE VALUENBAT0228S01Remarks: Specification data are reference values.
Terminal
No.Wire color Item ConditionJudgement
standard
(Approx.)
33 G/R LAN
ÐÐ
*: This terminal is connected to the ECM.
ON BOARD DIAGNOSIS LOGICNBAT0228S02
Diagnostic trouble code Malfunction is detected when ... Check item (Possible cause)
: A/T COMM LINE
The ECM-A/T communication line is
open or shorted.IHarness or connector
: 12th judgement flicker
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC A/T COMMUNICATION LINE
Description
AT-207

SAT014K
SAT971J
SAT682I
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION
PROCEDURE
NBAT0228S03After the repair, perform the following procedure to confirm the
malfunction is eliminated.
With CONSULT-II
1) Turn ignition switch ªONº.
2) Select ªDATA MONITORº mode for ªA/Tº with CONSULT-II.
3) Wait at least 6 seconds or start engine and wait for at least 6
seconds.
No Tools
1) Turn ignition switch ªONº.
2) Wait at least 6 seconds or start engine and wait for at least 6
seconds.
3) Perform self-diagnosis.
Refer to TCM SELF-DIAGNOSTIC PROCEDURE (No Tools),
AT-46.
DTC A/T COMMUNICATION LINE
Description (Cont'd)
AT-208

Diagnostic ProcedureNBAT0230
1 CHECK CIRCUIT BETWEEN TCM AND ECM
1. Turn ignition switch to OFF position.
2. Check continuity between TCM terminal 33 and ECM terminal 114.
SAT640JA
OK or NG
OK©GO TO 2.
NG©Repair or replace harness and connector between TCM and ECM.
2 CHECK DTC WITH ECM STEP 1
Perform self-diagnosis for engine control. Refer to EC-74, ªDESCRIPTIONº.
OK or NG
OK©GO TO 4.
NG©GO TO 3.
3 CHECK DTC WITH ECM STEP 2
Check ECM. Refer to EC-440 and EC-603, ªSystem Descriptionº and ªComponent Descriptionº.
OK or NG
OK©GO TO 4.
NG©Repair or replace damaged parts.
4 CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-208.
OK or NG
OK©INSPECTION END
NG©GO TO 5.
5 CHECK TCM INSPECTION
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK©INSPECTION END
NG©Repair or replace damaged parts.
DTC A/T COMMUNICATION LINE
Diagnostic Procedure
AT-210

SAT574J
DescriptionNBAT0207The TCM consists of a microcomputer and connectors for signal
input and output and for power supply. The unit controls the A/T.
ON BOARD DIAGNOSIS LOGICNBAT0207S01
Diagnostic trouble code Malfunction is detected when ... Check item (Possible cause)
: CONTROL UNIT (RAM)
: CONTROL UNIT (ROM)TCM memory (RAM) or (ROM) is mal-
functioning.TCM
SAT014K
SAT971J
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION
PROCEDURE
NBAT0207S02NOTE:
If ªDIAGNOSTIC TROUBLE CODE CONFIRMATION PROCE-
DUREº has been previously conducted, always turn ignition
switch ªOFFº and wait at least 5 seconds before conducting
the next test.
With CONSULT-II
1) Turn ignition switch ªONº and select ªDATA MONITORº mode
for A/T with CONSULT-II.
2) Start engine.
3) Run engine for at least 2 seconds at idle speed.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC CONTROL UNIT (RAM), CONTROL UNIT (ROM)
Description
AT-211

SAT574J
DescriptionNBAT0215The TCM consists of a microcomputer and connectors for signal
input and output and for power supply. The unit controls the A/T.
ON BOARD DIAGNOSIS LOGICNBAT0215S01
Diagnostic trouble code Malfunction is detected when ... Check item (Possible cause)
: CONT UNIT (EEP ROM)TCM memory (EEP ROM) is malfunc-
tioning.TCM
SAT014K
SAT971J
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION
PROCEDURE
NBAT0215S02NOTE:
If ªDIAGNOSTIC TROUBLE CODE CONFIRMATION PROCE-
DUREº has been previously conducted, always turn ignition
switch ªOFFº and wait at least 5 seconds before conducting
the next test.
With CONSULT-II
1) Turn ignition switch ªONº and select ªDATA MONITORº mode
for A/T with CONSULT-II.
2) Start engine.
3) Run engine for at least 2 seconds at idle speed.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC CONTROL UNIT (EEP ROM)
Description
AT-213

1. O/D OFF Indicator Lamp Does Not Come OnNBAT0073SYMPTOM:
O/D OFF indicator lamp does not come on for about 2 seconds
when turning ignition switch to ªONº.
1 CHECK TCM POWER SOURCE STEP 1
1. Turn ignition switch to ON position.
(Do not start engine.)
2. Check voltage between TCM terminals 10, 19, 28 and ground.
SAT611J
OK or NG
OK©GO TO 2.
NG©GO TO 3.
2 CHECK TCM POWER SOURCE STEP 2
1. Turn ignition switch to OFF position.
2. Check voltage between TCM terminal 28 and ground.
SAT612JC
OK or NG
OK©GO TO 4.
NG©GO TO 3.
3 DETECT MALFUNCTIONING ITEM
Check the following items:
IHarness for short or open between ignition switch and TCM terminals 10, 19 and 28 (Main harness)
IIgnition switch and 10A or 7.5A fuse [No. 18 or 24, located in the fuse block (J/B)]
Refer to EL-9, ªSchematicº.
OK or NG
OK©GO TO 4.
NG©Repair or replace damaged parts.
TROUBLE DIAGNOSES FOR SYMPTOMS
1. O/D OFF Indicator Lamp Does Not Come On
AT-218

2. Engine Cannot Be Started In ªPº and ªNº
Position
=NBAT0074SYMPTOM:
Engine cannot be started with selector lever in ªPº or ªNº
position.
Engine cannot be started with selector lever in ªPºEngine can
be started with selector lever in ªDº, ª2º, ª1º or ªRº position.
1 CHECK PNP SWITCH CIRCUIT
With CONSULT-II
Does ªTCM INPUT SIGNALSº in Data Monitor show damage to PNP switch circuit?
Without CONSULT-II
Does self-diagnosis show damage to PNP switch circuit?
SAT367J
YesorNo
Ye s©Check PNP switch circuit. Refer to ªDTC P0705º, AT-99.
No©GO TO 2.
2 CHECK PNP SWITCH INSPECTION
Check for short or open of PNP switch 2-pin connector. Refer to ªComponents Inspectionº, AT-103.
SAT838BB
OK or NG
OK©GO TO 3.
NG©Repair or replace PNP switch.
3 CHECK STARTING SYSTEM
Check starting system. Refer to SC-10, ªSystem Descriptionº.
OK or NG
OK©INSPECTION END
NG©Repair or replace damaged parts.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSES FOR SYMPTOMS
2. Engine Cannot Be Started In ªPº and ªNº Position
AT-221