2001 DODGE RAM key battery

Items found requiring adjustment and/or repair
should be corrected before delivery of the vehicle.
NOTE: It is the dealer's responsibility to protect
new vehicles from damage and deterioration prior
to retail delivery both before and after new vehicle
preparation.
The information includes the following features:
Inspection points are cross-referenced to the New
Vehicle Preparation Form as follows:
²Titles indicate the general area being inspected
or the types of checks being made (i.e., underhood,
body-exterior, road test, etc.).
²Sub-Titles identify the types of items to be
inspected in that area (i.e., lines/hoses, wiring, etc.).
Procedures follow a logical order to prevent dupli-
cation and wasted effort.
Tips to help you do a better job are found as
NOTES.
RECEIVING
INSPECTION
The following procedures are recommended for
your own protection upon receipt of new vehicles.
When a new car is delivered by the carrier, it should
be inspected to ensure that it is in good condition
and to determine if there is any shortage or transpor-
tation damage.
EXTERIOR
Upon receipt of a new vehicle, check immediately
for:
²Under carriage damage
²Chipped or cracked windshield, broken windows,
and loose or missing moldings and name-plates
²Dents, scrapes, scratches, chips, dirt in paints or
other damage to the body exterior
²Damaged or missing side view mirror(s)
²Missing wheel nuts
²Broken or missing lenses
²Chafing, bruises, cuts, or scrapes on tire side-
walls or tread
²Missing underhood items
²Missing fuel filler cap
²Shipped loose items-license plate bracket, spare
tire, jack and tire wrench, radio antenna, floor mats,
wheel covers, cargo nets, fuses and other items²Ensure that IOD fuse is removed
²Check battery test indicator when easily visible,
or use voltmeter (battery must be at 12.4 volts or
greater). Charge to ensure green dot-visibility, per-
manent damage may occur if battery remains in a
discharged state for any length of time.
INTERIOR
Check interior items such as:
²Rearview mirror
²Accessory control knobs
²Smokers package items
²Keys
²Radio
²Special equipment items listed on shipper
²Owner's Manual and Consumer information Bro-
chures (normally stored in the glove box).
²Cuts, abrasions or stains on interior trim.
NOTE: Remember a careful look at new vehicles
when they are received may prevent problems when
preparing vehicles for delivery to your customers.
MAJOR INSPECTION POINTS
(1) Check operation of hood latch and safety catch-
adjust as required.
(2) Check all fluids for proper level and top off
with the proper fluid as required-engine oil, auto-
matic transmission fluid, brake master cylinder,
clutch master cylinder, power steering, windshield
washer, and cooling system. (Vehicle must be at nor-
mal operating temperature for some of these checks.)
(3) Check brake, clutch, fuel, and power steering
lines and hoses for leaks and clearance from moving
and hot objects-reroute to the proper location and
tighten as required.
(4) Check battery state of charge-recharge if neces-
sary, to ensure green dot is visible or instrument
panel voltmeter indicates 12.4 volts or greater.
(5) Check routing and connections of underhood
wiring, vacuum hoses, refrigerant lines and coolant
hoses for leaks, loose connections and clearance from
moving objects reroute and tighten connections as
required. Install IOD fuse on applicable vehicles.
NOTE: Reset radio, clock, compass, etc., after
installing, if vehicle is being delivered.
BR/BENEW VEHICLE PREPARATION 30 - 3
INTRODUCTION (Continued)

STANDARD PROCEDURE - PRE DELIVERY
STORAGE
(1) If possible, store vehicles indoors, in clean, dry
places. If vehicles must be stored outdoors:
²Try to avoid storage locations that are near any
obvious sources of industrial or environmental con-
tamination (e.g., trees, factories, steam or vapor
vents, railroad tracks, etc.)
²Maintain tight security to help prevent pilferage
and vandalism, and inspect each vehicle regularly to
check for such damage
²If the vehicle must be parked on an incline, park
it with the front end higher than the rear; this will
prevent ªhydrostatic lockº caused by fuel draining
into the engine
²Rinse the vehicle at least once a week. Snow
should be washed away more often, since it can trap
harmful contaminants. Dry all horizontal surfaces
(2) The IOD fuse should be removed in order to
prevent battery drain and possible damage.
(3) Check the vehicle's coolant and anti-freeze pro-
tection.
(4) Check the vehicle's battery at least once a
month for a proper charge (at least 12.4 volts).
Charge the battery if necessary. This will help pre-
vent freezing and deterioration.
(5) Check the vehicle's tires and inflate them to
their maximum recommended levels. Move the vehi-
cles periodically to avoid ªflatspottingº the tires.
(6) Do not engage the parking brake; keep it in the
OFF position.
(7) Keep all windows closed, all doors locked, and
all trim covers intact and in place.
(8) Do not use chalks, crayons or any marker con-
taining abrasives on painted, plated or glass sur-
faces.
(9) Always use seat covers when moving a vehicle.
PROGRAMMABLE
ELECTRONIC FEATURES
DESCRIPTION
The programming of electronic features applies to
specific DaimlerChrysler Corporation vehicles. Not
all vehicles are equipped with these electronic fea-
tures, and not all vehicles equipped with electronic
features have all the available features. Programma-
ble electronic features are subject to change and may
be added or deleted from specific vehicle models.
(1) The programmable electronic features that may
be provided on the vehicle are:
²Rolling Power Door Locks
²Horn Chirp (When Doors Locked With Remote
Keyless Entry)²Headlamp Flash (When Doors Locked or
Unlocked With Remote Keyless Entry)
²Low Fuel Chime
²Remote Keyless Entry Door Unlock Sequence
²Headlights On Automatically With Wipers
²Turn Signal Chime
²12V Power Outlet
²Remote Unlock
²Remote Linked To Memory
²Headlamp Delay
²Service Interval
²Easy Exit Seat
(2) Programming any of the above features is to be
performed prior to vehicle delivery to the customer,
depending on customer preference.
NOTE: For all vehicles except Caravan/Town and
Country, the programming must be performed using
the DRB IIITscan tool. On Caravan/Town and Coun-
try vehicles the features can be programmed using
the DRB IIITscan tool or by button pushing
sequences. The customer can perform program-
ming, if desired, by following the instructions out-
lined in the owner manual.
OPERATION
NOTE: The programmable features provided on
vehicles need to be explained to the customer at
the time of sale. The customer's preferences con-
cerning the features should be noted and pro-
grammed accordingly during predelivery.
NOTE: When using the DRB IIITscan tool to enable/
disable any programmable electronic features, go to
the main menu item #9 on the DRB IIITscan tool.
This is ªCustomer Preferencesº. You must choose
ªCustomer Preferencesº on the main menu to pro-
gram the desired features.
ROLLING POWER DOOR LOCKS
With this feature enabled, the vehicle's door lock-
ing mechanisms automatically lock when the vehicle
reaches approximately 24 Km/h (15 mph).
HORN CHIRP
NOTE: This feature can be enabled with or without
the headlamp flash feature.
The horn chirp function is a feature that can be
enabled or disabled on vehicles equipped with
30 - 20 NEW VEHICLE PREPARATIONBR/BE
PRE DELIVERY STORAGE (Continued)

INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-66
INJECTION SYSTEM - DESCRIPTION, AIR . 25-25
INJECTION SYSTEM - DESCRIPTION,
DIESEL FUEL........................14-87
INJECTION SYSTEM - OPERATION, AIR . . . 25-27
INJECTION SYSTEM - TORQUE, AIR......25-28
INJECTOR - DESCRIPTION, FUEL . . . 14-53,14-93
INJECTOR - INSTALLATION, FUEL . . 14-53,14-98
INJECTOR - OPERATION, FUEL.....14-53,14-94
INJECTOR - REMOVAL, FUEL......14-53,14-96
INJECTOR FIRING ORDER, DIESEL -
FUEL..............................14-58
INJECTOR TEST - DIAGNOSIS AND
TESTING, FUEL.................14-53,14-95
INLET BAFFLE - INSTALLATION, HVAC
HOUSING...........................24-37
INLET BAFFLE - REMOVAL, HVAC
HOUSING...........................24-36
INLET FILTER - INSTALLATION..........14-22
INLET FILTER - REMOVAL..............14-22
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-154
IN/OUT - ADJUSTMENT, FRONT DOOR....23-69
INPUT - DESCRIPTION, VEHICLE SPEED . . . 8P-1
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-3
INSIDE HANDLE ACTUATOR -
INSTALLATION...................23-71,23-80
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-71,
23-80
INSPECTION - DESCRIPTION, ROAD
TEST..............................30-15
INSPECTION - DIAGNOSIS AND
TESTING, WHEEL....................22-10
INSPECTION - INFORMATION LABELS -
STANDARD PROCEDURE...............30-22
INSPECTION, 3.9L/5.2L/5.9L ENGINES -
VISUAL............................14-28
INSPECTION, 8.0L ENGINE - VISUAL.....14-32
INSPECTION, A/C COMPRESSOR
CLUTCH............................24-16
INSPECTION, ACCUMULATOR . . . 21-192,21-363,
21-538,21-708
INSPECTION, AUTOMATIC
TRANSMISSION - 42RE...............21-165
INSPECTION, AUTOMATIC
TRANSMISSION - 44RE...............21-337
INSPECTION, AUTOMATIC
TRANSMISSION - 46RE...............21-510
INSPECTION, AUTOMATIC
TRANSMISSION - 47RE...............21-681
INSPECTION, BATTERY.................30-7
INSPECTION, BATTERY SYSTEM..........8F-5
INSPECTION, BODY SEALING...........30-10
INSPECTION, CAMSHAFT & BEARINGS
(IN BLOCK).........................9-272
INSPECTION, CATALYTIC CONVERTER -
3.9L/5.2L/5.9L........................11-5
INSPECTION, CATALYTIC CONVERTER -
5.9L HEAVY DUTY/8.0L.................11-7
INSPECTION, CHARGE AIR COOLER AND
PLUMBING.........................11-18
INSPECTION, COMPASS...............30-12
INSPECTION, CROSSHEADS............9-250
INSPECTION, CYLINDER HEAD....9-137,9-193,
9-23,9-250,9-80
INSPECTION, CYLINDER HEAD COVER(S) . 9-138,
9-194,9-24,9-253,9-81
INSPECTION, DISC BRAKE CALIPERS......5-12
INSPECTION, DOORS AND DOOR LOCKS . . 30-11
INSPECTION, DRUM...................5-33
INSPECTION, ENGINE BLOCK . 9-142,9-200,9-267,
9-28,9-86
INSPECTION, ENGINE PERFORMANCE....30-16
INSPECTION, EXHAUST MANIFOLD . 9-112,9-168,
9-225,9-304,9-55
INSPECTION, EXHAUST PIPE -
3.9L/5.2L/5.9L........................11-7
INSPECTION, EXHAUST PIPE - 5.9L
DIESEL
.............................11-9
INSPECTION, EXHAUST PIPE - 5.9L
HEAVY DUTY/8.0L
.....................11-9
INSPECTION, FIT AND FINISH
......30-10,30-12
INSPECTION, FLUID LEVELS
.............30-4
INSPECTION, FRONT CLUTCH
. . . 21-205,21-376,
21-550,21-721INSPECTION, FRONT SERVO....21-207,21-378,
21-553,21-723
INSPECTION, FUEL...................30-15
INSPECTION, GAUGES/WARNING LIGHTS . 30-19
INSPECTION, HEATER/AIR CONDITIONER . . 30-17
INSPECTION, HOOD LATCH/SAFETY
CATCH ..............................30-4
INSPECTION, HORN..................30-19
INSPECTION, INTAKE MANIFOLD . . . 9-110,9-166,
9-223,9-302,9-53
INSPECTION, INTAKE/EXHAUST VALVES
& SEATS ..............9-141,9-198,9-27,9-84
INSPECTION, KEYLESS ENTRY..........30-11
INSPECTION, LIGHTS AND SWITCHES....30-12
INSPECTION, LINES/HOSES.............30-6
INSPECTION, MANUAL - NV3500........21-15
INSPECTION, MEASURING TIMING
CHAIN STRETCH.......9-114,9-170,9-227,9-58
INSPECTION, MIRROR................30-19
INSPECTION, NEUTRAL SAFETY SWITCH . . 30-19
INSPECTION, OIL COOLER & LINES -
CLEANING..........................9-296
INSPECTION, OIL PAN . 9-106,9-162,9-219,9-297,
9-49
INSPECTION, OIL PRESSURE RELIEF
VALVE .............................9-297
INSPECTION, OIL PUMP....9-107,9-163,9-220,
9-299,9-50
INSPECTION, OIL PUMP . . 21-211,21-382,21-557,
21-728
INSPECTION, OTHER..................30-15
INSPECTION, OVERDRIVE UNIT . . 21-224,21-394,
21-569,21-741
INSPECTION, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON RETAINER....21-236,
21-406,21-580,21-752
INSPECTION, PARKING BRAKE..........30-17
INSPECTION, PISTON & CONNECTING
ROD ............9-154,9-209,9-285,9-41,9-98
INSPECTION, PLANETARY GEARTRAIN/
OUTPUT SHAFT . . . 21-241,21-411,21-587,21-760
INSPECTION, PUSHRODS..............9-250
INSPECTION, RADIATOR - 3.9L/5.2L/5.9L . . . 7-61
INSPECTION, RADIATOR - 5.9L DIESEL....7-65
INSPECTION, RADIATOR - 8.0L..........7-62
INSPECTION, RADIATOR FAN -
3.9L/5.2L/5.9L/8.0L....................7-43
INSPECTION, RADIATOR FAN - 5.9L
DIESEL.............................7-44
INSPECTION, RADIATOR PRESSURE CAP . . . 7-66
INSPECTION, RADIO..................30-17
INSPECTION, REAR CLUTCH....21-248,21-419,
21-593,21-765
INSPECTION, RECEIVING...............30-3
INSPECTION, ROCKER ARM / ADJUSTER
ASSY..............................9-262
INSPECTION, SEAT BELTS, SHOULDER
BELTS, RETRACTORS AND HEAD
RESTRAINTS........................30-12
INSPECTION, SEATS..................30-13
INSPECTION, SERVICE BRAKES.........30-17
INSPECTION, SHIFT/CLUTCH INTERLOCK
SYSTEM............................30-19
INSPECTION, SOLID LIFTERS/TAPPETS . . . 9-281
INSPECTION, SPEED CONTROL.........30-17
INSPECTION, SQUEAKS, RATTLES AND
WIND NOISE........................30-15
INSPECTION, STEERING AND HANDLING
. . 30-15
INSPECTION, TAILPIPE - 3.9L/5.2L/5.9L
. . . 11-11
INSPECTION, TAILPIPE - 5.9L DIESEL
....11-12
INSPECTION, TAILPIPE - 5.9L HEAVY
DUTY/8.0L
..........................11-12
INSPECTION, TIRE PRESSURES
..........30-8
INSPECTION, TRANSFER CASE -
NV231HD
..........................21-832
INSPECTION, TRANSFER CASE -
NV241HD
..........................21-902
INSPECTION, TRANSFER CASE -
NV241LD
..........................21-867
INSPECTION, TRANSMISSION
.....21-109,21-64
INSPECTION, TRANSMISSION/TRANSFER
CASE
..............................30-15
INSPECTION, TRIP COMPUTER/
MAINTENANCE REMINDER
.............30-17
INSPECTION, TURBOCHARGER
..........11-16
INSPECTION, TURN AND EMERGENCY
SIGNALS
...........................30-19INSPECTION, VALVE BODY......21-293,21-465,
21-637,21-809
INSPECTION, VIBRATION DAMPER.......9-289
INSPECTION, VISUAL..................30-8
INSPECTION, WATER PUMP -
3.9L/5.2L/5.9L........................7-69
INSPECTION, WATER PUMP - 5.9L
DIESEL.............................7-73
INSPECTION, WATER PUMP - 8.0L........7-72
INSPECTION, WHEEL CYLINDERS........5-31
INSPECTION, WINDOWS, DOORS AND
LOCKS.............................30-14
INSPECTION WINDSHIELD WIPERS/
WASHERS, ROAD TEST................30-18
INSPECTION, WIPER & WASHER
SYSTEM............................8R-6
INSPECTION, WIRING..................30-7
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-205
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-204
INSTRUMENT CLUSTER - ASSEMBLY.....8J-13
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-6
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-11
INSTRUMENT CLUSTER - INSTALLATION . . 8J-14
INSTRUMENT CLUSTER - OPERATION.....8J-3
INSTRUMENT CLUSTER - REMOVAL.....8J-10
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-10
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-9
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL SYSTEM -
DESCRIPTION......................23-104
INSTRUMENT PANEL SYSTEM -
INSTALLATION......................23-107
INSTRUMENT PANEL SYSTEM -
OPERATION........................23-105
INSTRUMENT PANEL SYSTEM -
REMOVAL.........................23-106
INSTRUMENT PANEL TOP COVER -
INSTALLATION......................23-115
INSTRUMENT PANEL TOP COVER -
REMOVAL.........................23-114
INTAKE AIR HEATER - DESCRIPTION....14-100
INTAKE AIR HEATER - INSTALLATION....14-101
INTAKE AIR HEATER - OPERATION......14-100
INTAKE AIR HEATER - REMOVAL.......14-100
INTAKE AIR HEATER RELAY -
DESCRIPTION......................14-101
INTAKE AIR HEATER RELAY -
INSTALLATION......................14-102
INTAKE AIR HEATER RELAY -
OPERATION........................14-102
INTAKE AIR HEATER RELAY - REMOVAL . 14-102
INTAKE MANIFOLD - CLEANING
....9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - DESCRIPTION
. 9-109,9-165,
9-222,9-52
INTAKE MANIFOLD - INSPECTION
. . 9-110,9-166,
9-223,9-302,9-53
INTAKE MANIFOLD - INSTALLATION
.....9-111,
9-166,9-223,9-302,9-53
INTAKE MANIFOLD - OPERATION
. . 9-109,9-165,
9-52
INTAKE MANIFOLD - REMOVAL
....9-110,9-166,
9-222,9-301,9-53
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING
. . . 9-110,9-165,9-222,
9-53
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.............9-140,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
.....9-138,9-195,9-25,9-253,9-81
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...........9-141,9-198,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION
.........9-141,9-260,9-28,9-85
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL
.............9-140,9-258,9-27,9-84
INTAKE/EXHAUST VALVES & SEATS -
STANDARD PROCEDURE-
VALVES,GUIDES AND SPRINGS
.........9-253
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page

INTAKE/EXHAUST VALVES & SEATS -
VALVE SERVICE......................9-195
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER AND TUBES - WITHOUT
RADIATOR...................7-80,7-83,7-86
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR...................7-79,7-83,7-85
INTERIOR - CAUTION................23-118
INTERLOCK SYSTEM - INSPECTION,
SHIFT/CLUTCH.......................30-19
INTERMEDIATE - INSTALLATION, AXLE
SHAFTS.............................3-28
INTERMEDIATE - REMOVAL, AXLE
SHAFTS.............................3-28
INTERMEDIATE AXLE - INSTALLATION.....3-61
INTERMEDIATE AXLE - REMOVAL.........3-60
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-6
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-3
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . 9-118,9-173,9-3
INTRODUCTION - DIAGNOSIS AND
TESTING-ENGINE DIAGNOSIS............9-61
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
IOD FUSE - DESCRIPTION...........8W-97-4
IOD FUSE - INSTALLATION...........8W-97-5
IOD FUSE - OPERATION.............8W-97-5
IOD FUSE - REMOVAL................8W-97-5
ISO FLARING - STANDARD PROCEDURE....5-8
ITEMS - INSTALLATION, SHIPPED LOOSE . 30-14
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL.........................2-12
JOINT - INSTALLATION, LOWER BALL.....2-25
JOINT - INSTALLATION, UPPER BALL.....2-25
JOINT MOLDING - INSTALLATION, ROOF . . 23-91
JOINT MOLDING - REMOVAL, ROOF......23-91
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL..................3-11
JOINTS - INSTALLATION, SINGLE
CARDAN UNIVERSAL..............3-34,3-66
JOINTS - REMOVAL, SINGLE CARDAN
UNIVERSAL......................3-33,3-65
JOUNCE BUMPER - DESCRIPTION.....2-28,2-9
JOUNCE BUMPER - OPERATION.......2-28,2-9
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD
BEARING AND CRANKSHAFT...........9-274
JUMP STARTING - STANDARD
PROCEDURE.........................0-27
JUNCTION BLOCK - DESCRIPTION.....8W-97-6
JUNCTION BLOCK - INSTALLATION....8W-97-7
JUNCTION BLOCK - OPERATION......8W-97-6
JUNCTION BLOCK - REMOVAL........8W-97-6
KEEPER - INSTALLATION, BACKLITE
LATCH ............................23-146
KEEPER - REMOVAL, BACKLITE LATCH . . 23-146
KEY LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH............19-10
KEY-IN IGNITION SWITCH -
DESCRIPTION........................19-9
KEYLESS ENTRY - INSPECTION.........30-11
KEYLESS ENTRY SYSTEM -
DESCRIPTION, REMOTE................8N-2
KEYLESS ENTRY SYSTEM - DIAGNOSIS
AND TESTING, POWER LOCK &
REMOTE............................8N-4
KEYLESS ENTRY SYSTEM - OPERATION,
REMOTE............................8N-3
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-7
KEYLESS ENTRY TRANSMITTER -
OPERATION, REMOTE..................8N-7
KNOB - INSTALLATION, TURNING LOOP
HEIGHT ADJUSTER
...................8O-30
KNOB - REMOVAL, TURNING LOOP
HEIGHT ADJUSTER
...................8O-30
KNUCKLE - DESCRIPTION
............2-20,2-9
KNUCKLE - INSTALLATION
..........2-10,2-20
KNUCKLE - OPERATION
............2-10,2-20KNUCKLE - REMOVAL..............2-10,2-20
LABEL - DESCRIPTION, VECI.........Intro.-10
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION....................Intro.-12
LABEL - OPERATION, VECI...........Intro.-10
LABELS - STANDARD PROCEDURE,
INSPECTION - INFORMATION...........30-22
LAMP - DESCRIPTION, READING........8L-36
LAMP - DESCRIPTION, TAIL............8L-29
LAMP - DIAGNOSIS AND TESTING, FOG . . . 8L-9
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, CLEARANCE......8L-6
LAMP - INSTALLATION, DOME..........8L-33
LAMP - INSTALLATION, FOG............8L-11
LAMP - INSTALLATION, LICENSE PLATE . . 8L-22
LAMP - INSTALLATION, MARKER........8L-23
LAMP - INSTALLATION, OUTBOARD
IDENTIFICATION.....................8L-29
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-29
LAMP - INSTALLATION, READING........8L-36
LAMP - INSTALLATION, TAIL...........8L-30
LAMP - INSTALLATION, UNDERHOOD....8L-32
LAMP - INSTALLATION, VANITY.........8L-37
LAMP - OPERATION, READING..........8L-36
LAMP - OPERATION, TAIL..............8L-29
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, CLEARANCE..........8L-6
LAMP - REMOVAL, DOME..............8L-33
LAMP - REMOVAL, FOG...............8L-11
LAMP - REMOVAL, LICENSE PLATE......8L-22
LAMP - REMOVAL, MARKER...........8L-22
LAMP - REMOVAL, OUTBOARD
IDENTIFICATION.....................8L-28
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-29
LAMP - REMOVAL, READING...........8L-36
LAMP - REMOVAL, TAIL...............8L-29
LAMP - REMOVAL, UNDERHOOD........8L-31
LAMP - REMOVAL, VANITY.............8L-37
LAMP AND SWITCH - INSTALLATION,
GLOVE BOX.........................8L-35
LAMP AND SWITCH - REMOVAL, GLOVE
BOX ...............................8L-35
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-24
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR.............8J-24
LAMP MODULE - DESCRIPTION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - INSTALLATION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - OPERATION, DAYTIME
RUNNING............................8L-9
LAMP MODULE - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP SWITCH - DESCRIPTION, BRAKE....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE......................8L-5
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-5
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP UNIT - ADJUSTMENTS, FOG.......8L-12
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, FOG.......8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-22
LAMP UNIT - INSTALLATION, PARK/
TURN SIGNAL.......................8L-29
LAMP UNIT - INSTALLATION, TAIL.......8L-30
LAMP UNIT - INSTALLATION,
UNDERHOOD........................8L-32
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, FOG...........8L-11
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-22
LAMP UNIT - REMOVAL, PARK/TURN
SIGNAL............................8L-29
LAMP UNIT - REMOVAL, TAIL...........8L-30
LAMP UNIT - REMOVAL, UNDERHOOD . . . 8L-32
LASH ADJUSTMENT AND VERIFICATION
- STANDARD PROCEDURE, VALVE
.......9-256
LATCH - ADJUSTMENT
...............23-100
LATCH - ADJUSTMENT, FRONT DOOR
....23-72
LATCH - INSTALLATION
....23-100,23-64,23-72
LATCH - INSTALLATION, SAFETY
.......23-102LATCH - LOWER - INSTALLATION........23-80
LATCH - LOWER - REMOVAL...........23-80
LATCH - REMOVAL........23-100,23-64,23-72
LATCH - REMOVAL, SAFETY...........23-102
LATCH - UPPER - INSTALLATION........23-81
LATCH - UPPER - REMOVAL............23-81
LATCH AND KEEPER - INSTALLATION,
BACKLITE.........................23-146
LATCH AND KEEPER - REMOVAL,
BACKLITE.........................23-146
LATCH HANDLE - INSTALLATION........23-65
LATCH HANDLE - REMOVAL............23-65
LATCH RELEASE CABLE - INSTALLATION . 23-101
LATCH RELEASE CABLE - REMOVAL....23-101
LATCH STRIKER - ADJUSTMENT.......23-102
LATCH STRIKER - INSTALLATION . 23-102,23-65,
23-73
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-113
LATCH STRIKER - LOWER -
INSTALLATION.......................23-82
LATCH STRIKER - LOWER - REMOVAL....23-82
LATCH STRIKER - REMOVAL.....23-102,23-65,
23-73
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-113
LATCH STRIKER - UPPER -
INSTALLATION.......................23-82
LATCH STRIKER - UPPER - REMOVAL....23-82
LATCH/SAFETY CATCH - INSPECTION,
HOOD..............................30-4
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID . . . 21-148,21-319,
21-491,21-662
LEAK DETECTION PUMP - DESCRIPTION . . 25-33
LEAK DETECTION PUMP - INSTALLATION . 25-34
LEAK DETECTION PUMP - REMOVAL.....25-34
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-2
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE....9-124,
9-179,9-67,9-9
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD.....9-110,9-165,9-222,9-53
LEAKAGE - DIAGNOSIS AND TESTING,
POWER STEERING GEAR..............19-14
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-31
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-5
LEAKS - DIAGNOSIS AND TESTING,
ENGINE OIL...........9-104,9-160,9-215,9-47
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-74
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-10
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-43
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURES,
REPAIRING..........................22-8
LEFT FRONT FENDER - INSTALLATION....23-93
LEFT FRONT FENDER - REMOVAL.......23-92
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-199,21-370,
21-545,21-715
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-14
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE.......8F-8
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-57
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-16
LEVEL CHECK - STANDARD
PROCEDURE, FLUID.....21-199,21-370,21-545,
21-715
LEVEL, OIL - STANDARD PROCEDURE-
ENGINE OIL
.........................9-295
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
..............14-7,14-73
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
..................14-9
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
................14-7,14-73
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-8
20 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER AND TUBES - WITHOUT
RADIATOR IN-TANK...........7-80,7-83,7-86
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR IN-TANK...........7-79,7-83,7-85
TRANSMISSION OVERTEMP INDICATOR
- DESCRIPTION......................8J-31
TRANSMISSION OVERTEMP INDICATOR
- OPERATION........................8J-31
TRANSMISSION, SPECIAL TOOLS -
NV5600 MANUAL...................21-127
TRANSMISSION, SPECIAL TOOLS - RE . . 21-534,
21-704
TRANSMISSION, SPECIFICATIONS......21-186,
21-532,21-702
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION . . . 21-262,21-433,21-606,21-779
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.....21-262,21-433,21-606,21-779
TRANSMISSION THROTTLE VALVE
CABLE - ADJUSTMENTS . 21-254,21-425,21-598,
21-771
TRANSMISSIONS, SPECIAL TOOLS - RE . 21-188,
21-359
TRANSMISSION/TRANSFER CASE -
INSPECTION........................30-15
TRANSMITTER - DESCRIPTION, REMOTE
KEYLESS ENTRY......................8N-7
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY......8N-7
TRANSMITTER - OPERATION, REMOTE
KEYLESS ENTRY......................8N-7
TRANSMITTER BATTERIES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE, RKE...........8N-8
TRAY - DESCRIPTION, BATTERY.........8F-24
TRAY - INSTALLATION, BATTERY........8F-25
TRAY - INSTALLATION, REAR FLOOR
STOWAGE.........................23-121
TRAY - OPERATION, BATTERY..........8F-25
TRAY - REMOVAL, BATTERY............8F-25
TRAY - REMOVAL, REAR FLOOR
STOWAGE.........................23-121
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-7
TRIM - INSTALLATION, A-PILLAR.......23-119
TRIM - INSTALLATION, B-PILLAR.......23-120
TRIM - INSTALLATION, C-PILLAR.......23-128
TRIM - INSTALLATION, DOOR SILL.....23-121
TRIM - INSTALLATION, GLOVE BOX
OPENING UPPER....................23-114
TRIM - INSTALLATION, REAR CLOSURE
PANEL............................23-121
TRIM - REMOVAL, A-PILLAR..........23-119
TRIM - REMOVAL, B-PILLAR..........23-120
TRIM - REMOVAL, C-PILLAR..........23-128
TRIM - REMOVAL, DOOR SILL.........23-121
TRIM - REMOVAL, GLOVE BOX OPENING
UPPER............................23-114
TRIM - REMOVAL, REAR CLOSURE
PANEL............................23-120
TRIM COVER - INSTALLATION, COWL . . . 23-120
TRIM COVER - REMOVAL, COWL.......23-119
TRIM PANEL - INSTALLATION......23-74,23-84
TRIM PANEL - INSTALLATION, QUARTER . 23-128
TRIM PANEL - REMOVAL.........23-74,23-84
TRIM PANEL - REMOVAL, QUARTER....23-127
TRIP COMPUTER/MAINTENANCE
REMINDER - INSPECTION..............30-17
TRIP DEFINITION - DESCRIPTION........25-18
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TRUCK MAINTENANCE SCHEDULE (8.0L
2500 & 3500 MODELS - CALIFORNIA
ONLY) - DESCRIPTION, MEDIUM DUTY....0-13
TUBE - DESCRIPTION, A/C ORIFICE
......24-53
TUBE - DIAGNOSIS AND TESTING, FIXED
ORIFICE
............................24-54
TUBE - OPERATION, A/C ORIFICE
........24-53
TUBE - REMOVAL, A/C ORIFICE
.........24-54
TUBES - WITH RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS
...................7-79,7-83,7-85TUBES - WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER....................7-80,7-83,7-86
TURBO DIESEL - DESCRIPTION,
MAINTENANCE SCHEDULES -
24-VALVE CUMMINS...................0-22
TURBOCHARGER - CLEANING..........11-16
TURBOCHARGER - DESCRIPTION........11-13
TURBOCHARGER - INSPECTION.........11-16
TURBOCHARGER - INSTALLATION.......11-16
TURBOCHARGER - OPERATION.........11-13
TURBOCHARGER - REMOVAL...........11-15
TURN AND EMERGENCY SIGNALS -
INSPECTION........................30-19
TURN SIGNAL & HAZARD WARNING
SYSTEM - DESCRIPTION...............8L-2
TURN SIGNAL & HAZARD WARNING
SYSTEM - DIAGNOSIS AND TESTING......8L-3
TURN SIGNAL & HAZARD WARNING
SYSTEM - OPERATION.................8L-2
TURN SIGNAL CANCEL CAM -
DESCRIPTION.......................8L-30
TURN SIGNAL CANCEL CAM -
OPERATION.........................8L-31
TURN SIGNAL INDICATORS -
DESCRIPTION.......................8J-32
TURN SIGNAL INDICATORS - DIAGNOSIS
AND TESTING.......................8J-32
TURN SIGNAL INDICATORS -
OPERATION.........................8J-32
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT..............8O-29
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT .........................8O-29
TURNING LOOP HEIGHT ADJUSTER
KNOB - INSTALLATION................8O-30
TURNING LOOP HEIGHT ADJUSTER
KNOB - REMOVAL....................8O-30
TWEETER SPEAKER - INSTALLATION,
A-PILLAR...........................8A-19
TWEETER SPEAKER - REMOVAL,
A-PILLAR...........................8A-19
UNDERHOOD LAMP - INSTALLATION.....8L-32
UNDERHOOD LAMP - REMOVAL.........8L-31
UNDERHOOD LAMP UNIT -
INSTALLATION.......................8L-32
UNDERHOOD LAMP UNIT - REMOVAL....8L-32
UNIT - ADJUSTMENTS, FOG LAMP.......8L-12
UNIT - ADJUSTMENTS, HEADLAMP......8L-21
UNIT - ASSEMBLY, OVERDRIVE . . 21-225,21-395,
21-569,21-742
UNIT - CLEANING, OVERDRIVE . . 21-224,21-394,
21-568,21-741
UNIT - DIAGNOSIS AND TESTING, FUEL
GAUGE SENDING......................14-8
UNIT - DISASSEMBLY, OVERDRIVE.....21-217,
21-387,21-562,21-734
UNIT - INSPECTION, OVERDRIVE......21-224,
21-394,21-569,21-741
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP.................8L-6
UNIT - INSTALLATION, FOG LAMP.......8L-12
UNIT - INSTALLATION, HEADLAMP.......8L-20
UNIT - INSTALLATION, LICENSE PLATE
LAMP..............................8L-22
UNIT - INSTALLATION, OVERDRIVE.....21-234,
21-404,21-577,21-750
UNIT - INSTALLATION, PARK/TURN
SIGNAL LAMP.......................8L-29
UNIT - INSTALLATION, TAIL LAMP.......8L-30
UNIT - INSTALLATION, UNDERHOOD
LAMP..............................8L-32
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP.................8L-6
UNIT - REMOVAL, FOG LAMP...........8L-11
UNIT - REMOVAL, HEADLAMP..........8L-20
UNIT - REMOVAL, LICENSE PLATE LAMP . . 8L-22
UNIT - REMOVAL, OVERDRIVE . . 21-216,21-387,
21-560,21-733
UNIT - REMOVAL, PARK/TURN SIGNAL
LAMP
..............................8L-29
UNIT - REMOVAL, TAIL LAMP
...........8L-30
UNIT - REMOVAL, UNDERHOOD LAMP
. . . 8L-32
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING
.................14-7,14-73
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING
......................14-9UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING.................14-7,14-73
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING......................14-8
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN......................3-11
UNIVERSAL JOINTS - INSTALLATION,
SINGLE CARDAN..................3-34,3-66
UNIVERSAL JOINTS - REMOVAL, SINGLE
CARDAN........................3-33,3-65
UP/DOWN - ADJUSTMENT, FRONT DOOR . 23-69
UPPER - INSTALLATION, LATCH.........23-81
UPPER - INSTALLATION, LATCH
STRIKER...........................23-82
UPPER - REMOVAL, LATCH............23-81
UPPER - REMOVAL, LATCH STRIKER.....23-82
UPPER BALL JOINT - DIAGNOSIS AND
TESTING............................2-12
UPPER BALL JOINT - INSTALLATION......2-25
UPPER CONTROL ARM - INSTALLATION . . . 2-13,
2-24
UPPER CONTROL ARM - REMOVAL . . . 2-13,2-23
UPPER CORNER SEAL - INSTALLATION,
FRONT DOOR......................23-154
UPPER CORNER SEAL - REMOVAL,
FRONT DOOR......................23-154
UPPER TRIM - INSTALLATION, GLOVE
BOX OPENING......................23-114
UPPER TRIM - REMOVAL, GLOVE BOX
OPENING..........................23-114
UPSHIFT INDICATOR - DESCRIPTION.....8J-33
UPSHIFT INDICATOR - OPERATION.......8J-33
USAGE - DESCRIPTION, FASTENER.....Intro.-6
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
V-10 - DESCRIPTION, 8.0L..............8I-1
V-10 - OPERATION, 8.0L................8I-1
V-10 ENGINE - IGNITION COIL
RESISTANCE, 8.0L.....................8I-3
V-10 ENGINE - SPARK PLUG CABLE
ORDER, 8.0L.........................8I-2
V-6 ENGINE - ENGINE FIRING ORDER,
3.9L................................8I-2
V-6/V-8 - DESCRIPTION.................8I-1
V-6/V-8 - OPERATION..................8I-1
V-6/V-8 ENGINES - DESCRIPTION........25-35
V-6/V-8 ENGINES - DIAGNOSIS AND
TESTING, PCV VALVE.................25-36
V-6/V-8 ENGINES - OPERATION.........25-35
V-8 ENGINES - ENGINE FIRING ORDER,
5.2L/5.9L............................8I-2
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-29
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-29
VACUUM MOTOR - ASSEMBLY, AXLE . . 3-33,3-65
VACUUM MOTOR - DESCRIPTION, AXLE . . . 3-29,
3-62
VACUUM MOTOR - DIAGNOSIS AND
TESTING........................3-31,3-63
VACUUM MOTOR - DISASSEMBLY, AXLE . . 3-33,
3-65
VACUUM MOTOR - INSTALLATION, AXLE . . 3-33,
3-65
VACUUM MOTOR - OPERATION, AXLE . 3-30,3-62
VACUUM MOTOR - REMOVAL, AXLE . . 3-33,3-65
VACUUM PUMP - 5.9L DIESEL -
DESCRIPTION........................7-34
VACUUM PUMP - 5.9L DIESEL -
INSTALLATION
........................7-37
VACUUM PUMP - 5.9L DIESEL -
OPERATION
..........................7-35
VACUUM PUMP - 5.9L DIESEL -
REMOVAL
...........................7-35
VACUUM PUMP OUTPUT - DIAGNOSIS
AND TESTING
........................7-35
VACUUM RESERVOIR - DESCRIPTION
....24-29
VACUUM RESERVOIR - DESCRIPTION
....8P-13
VACUUM RESERVOIR - INSTALLATION
....24-30
VACUUM RESERVOIR - INSTALLATION
. . . 8P-14
VACUUM RESERVOIR - OPERATION
......24-29
VACUUM RESERVOIR - REMOVAL
.......24-30
VACUUM RESERVOIR - REMOVAL
.......8P-13
VACUUM SCHEMATICS - DIAGNOSIS
AND TESTING
.......................25-37
VACUUM SUPPLY - DIAGNOSIS AND
TESTING
............................8P-2
BR/BEINDEX 37
Description Group-Page Description Group-Page Description Group-Page